After delivering new household appliances to the kitchen, the question often arises of how to properly perform the first startup so as not to damage the compressor. In the case of products Beko the procedure is standard, but has its own nuances, especially if the unit was transported in a horizontal position. Ignoring the rules of primary activation can lead to failure of the cooling system already in the first hours of operation.
Modern models are equipped with electronic control, which requires correct adjustment after applying voltage. Even if you just moved refrigerator round the kitchen, it takes time for the refrigerant to stabilize. In this article, we will analyze all the stages of switching on, from checking the electrical network to setting temperature conditions through the control panel.
Preparing the refrigerator for the first start
Before looking for the power button, you need to make sure that the device is ready for use. If Beko refrigerator you just brought it from the store, you need to let it settle. This time is necessary for the oil that got into the system tubes during transportation to flow back into the Beko refrigerator compressor. The settling time depends on the ambient temperature and the method of transportation. In winter, this process may take longer as oils tend to thicken in the cold. Do not rush to connect so as not to create excess pressure in the system..
The settling time depends on the ambient temperature and the method of transportation. In winter, this process may take longer as oils tend to thicken in the cold. Do not rush to connect so as not to create excess pressure in the system.
⚠️ Attention: If the device was transported lying down, the minimum waiting time before turning on should be at least 8-10 hours, even if the instructions allow shorter periods for vertical transportation.
It is also important to conduct a visual inspection of the rear wall. Make sure the capacitor (black grille) is not dented and the power cord has not been damaged by rodents or movers. Any mechanical damage can cause a short circuit when current is supplied.
Checking the electrical network and connecting
Safety of operation begins with proper organization power supply. Power of a modern refrigerator is small, but the starting currents of the compressor can be significant. Therefore, it is strictly not recommended to use various tees, extension cords or old sockets with poor contact.
The ideal option is a separate grounded socket located in close proximity to the equipment. If you are forced to use a surge protector, make sure that it is rated for the appropriate current load and has overload protection.
The plug should be inserted tightly until it stops. If you hear a cracking sound or see sparking, stop the operation immediately and call an electrician. Unstable voltage in the network can damage electronic module controls, the repair of which will be expensive.
- 🔌 Make sure that the voltage in the network corresponds to 220–230 Volts.
- 🔌 Check for grounding in the socket with using the indicator.
- 🔌 Do not connect the refrigerator to the same outlet with powerful appliances (washing machine, microwave).
The location of the control panel and the power button
The control interface for different models Beko may differ. In budget series with mechanical controls, there may not be a separate “Power” button at all - the device starts working immediately after connecting to the network. The adjustment is carried out by turning the thermostat inside the chamber.
In models with a system No Frost and an electronic display, startup often requires activation via the touch panel. The power button can be hidden or combined with the power indicator. On some displays, you need to hold the button for several seconds to unlock the control panel.
Where to look for the button if it is not on the door?
In some models, the power button is located inside the refrigerator compartment, next to the ceiling light, or hidden behind the decorative panel in the upper part.
Pay attention to the indication. If after connection the indicator lights up, but the compressor is silent, the protection may have tripped or the energy saving function has been selected. In this case, manual activation via the menu is required.
Step-by-step instructions: how to start a refrigerator
The process of activating equipment Beko is logical and similar for most modern models. The main thing is to follow the sequence of actions so that the self-diagnosis system passes all stages successfully.
First, make sure that the doors are tightly closed. If the door sensor is active, the refrigerator may not start the compressor, thinking that it is in the process of loading food or defrosting. Then press the power button on the control panel.
⚠️ Attention: On models with a display, after turning on, you may need to reset the settings to factory settings if the previous owner or tester at the factory changed the settings. This is usually done by long pressing the key combination.
After issuing the start command, you should hear a characteristic click of the relay and the hum of the motor. If silence persists for more than 5–10 minutes and the indicators are on, there may be a failure in the electronics or the starter protection mechanism is faulty.
☑️ Algorithm for first switching on
Setting temperature modes
Immediately after switching on, do not load the refrigerator with food. Let it run idle for at least 2-3 hours to gain the necessary temperature. Factory settings are usually optimal, but they can be adjusted to suit your needs.
For the refrigerator compartment, the recommended value is the range from +3 to +5 degrees Celsius. In the freezer, the standard is -18 degrees. If you set the mode Super Freeze (super freezing), the temperature will drop lower, but this mode is not intended for constant operation.
| Operating mode | Temperature (HC) | Temperature (MK) | Recommendation |
|---|---|---|---|
| Eco / Standard | +4°C | -18°C | Daily use |
| Maximum cooling | +2°C | -20°C | Loading a large volume of products |
| Vacation | +14°C | Works | Long time away from home |
| Super freezing | Does not change | -24°C | Fast freezing (automatically turns off) |
Do not install minimum values are unnecessary. This will lead to increased energy consumption and accelerated wear of the compressor. Adjust the cooling power depending on the load of the chambers and the temperature in the room.
What to do if the refrigerator does not turn on
Lack of response to turning on is a common problem that does not always indicates a breakdown. Often the reason lies in banal things that the user can check on their own.
First of all, check for voltage in the outlet by connecting another device, for example, a hair dryer or lamp. If the outlet is OK, inspect the power cord and plug. Sometimes the problem lies in the thermostat, which could be “stuck” in the “off” position.
If the refrigerator hums but does not cool, or turns on for a couple of seconds and turns off with a click, this may indicate a problem with the compressor start relay or a freon leak. In such cases, independent repair is dangerous.
- 🛠 Check whether the control panel is locked (Child Lock function).
- 🛠 Make sure the door fits tightly and the magnetic sensor is working properly.
- 🛠 Try unplugging the device for 15 minutes to reboot controller.
⚠️ Attention: If you hear a burning smell or see smoke, immediately disconnect the refrigerator from the power supply and do not try to turn it on again until the technician arrives.
Frequently asked questions (FAQ)
How long should a Beko refrigerator run before loading food?
It is recommended to let the device run empty for 2-4 hours. This will stabilize the temperature in all corners of the chambers and ensure that the system is working properly before you place supplies there.
Why does the alarm indicator light up after switching on?
The alarm indicator (often a red triangle or flashing symbol) lights up when the temperature inside the chambers is higher than normal. When you turn it on for the first time, this is normal because the refrigerator has not yet cooled down. After a few hours of operation, it should go out.
Is it possible to turn on the Beko refrigerator immediately after defrosting?
Yes, if you carried out a scheduled defrost and just wiped off the water, there is no need to wait. You can turn on the device immediately after you have made sure that the internal surfaces are dry and have closed the doors.
What does a flashing display mean when you try to turn it on?
Flashing of the display may indicate that the buttons are blocked or an error in the system. Try unlocking the panel (usually by holding down the lock button for 3 seconds). If the blinking continues, refer to the error codes in the instructions.