Purchasing a new one refrigerator Indesit is always an exciting moment, especially when you connect the appliance to the power supply for the first time. A logical question immediately arises: how long should the unit operate without stopping to reach the required temperature? Many users mistakenly believe that the device should freeze food in 15-20 minutes and stop immediately, but the physics of the operation dictates its conditions. of the refrigeration circuit dictates its terms.
In reality, the primary cooling process takes much longer than subsequent cold maintenance cycles. If you just brought the refrigerator home, let it sit and plug it in, don’t expect instant results. Compressor it takes time to circulate the refrigerant through the entire pipe system, cool the walls of the chambers and stabilize the temperature. Typically, this takes from 4 to 8 hours of continuous operation, depending on the model and ambient temperature.
It is important to understand that during this period thermostat or electronic module the controls do not yet record the achievement of target indicators, so the command to stop the engine is not received. Trying to load the refrigerator with food right away can throw off the sensors and increase the first cycle time. Let's look in detail at what is considered normal, and when to sound the alarm and call a technician.
Standard indicators for compressor operating time
Standard operating cycle of any modern refrigerator, including popular models Indesit, is based on alternating periods of engine operation and rest. After the first power-up, this cycle may look different than during normal operation. Normally, the first launch can last up to 8 hours without a break, if the chamber is warm. However, in normal mode, when the temperature has already been reached, compressor should be turned off.
The duration of one full cycle (work + rest) averages from 15 to 30 minutes, of which about 10-20 minutes are spent on engine operation. If your refrigerator Indesit works for 40 minutes and rests for 10, this is not yet a breakdown, but already a signal of increased load. The mode when the equipment works for days without stopping or, conversely, turns on for 1 minute and turns off is considered critical.
It is worth considering that the operating time is directly affected defrosting system. In models with No Frost cycles may be shorter, but the frequency of switching on is higher, as the system fights ice on the evaporator. In drip systems (Drip System), the compressor can work longer, but with long breaks, waiting for natural defrosting of the back wall.
⚠️ Attention: If after 12 hours of continuous operation after the first turn on the refrigerator Indesit does not turn off and does not become cold inside, this is obvious a sign of a freon malfunction or leak. In such a situation, further operation is pointless.
Factors influencing the duration of the first cycle
Why does one refrigerator turn off after 4 hours, while the other has been buzzing for 10? The answer lies in a combination of external and internal factors. The first and most important is the volume of the chambers. Large models Indesit with a full No Frost zone of freshness require more time to cool massive plastic and metal structural elements than compact two-chamber options.
The temperature in the room also plays a huge role. If you turn on the refrigerator in the summer in a hot kitchen, where +30°C, heat transfer it happens more slowly. The condenser on the rear wall does not have time to effectively transfer heat, and the compressor is forced to work in increased mode. In winter, at +18°C, the same unit will gain temperature much faster.
Another nuance is the presence or absence of an initial load. An empty refrigerator cools down faster, but is less stable. If you loaded a lot of warm products at once, thermostat will keep the compressor on until the heat-intensive products give up their degree. This is an absolutely normal physical reaction of the system.
Differences in the operation of the No Frost and drip system models
Cooling technology determines the algorithm of the motor operation. In refrigerators Indesit with a system No Frost the fan drives air through special channels. Here it is important not only to cool the air, but also to dry the evaporator. Therefore, the first cycle can be long, but after reaching the mode you will hear characteristic clicks and noise of the fan more often than the hum of the compressor.
In drip models (Cool Plus or analogue) everything is simpler: cold air falls down naturally. Here the shutdown cycle depends solely on warm-up thermostat, which is usually built into one of the walls of the chamber. If the sensor is “stuck” or incorrectly calibrated, the compressor may not turn off at all.
Modern models Indesit are often equipped with inverter compressors. Their operating principle is radically different from old linear motors. They do not turn off completely, but reduce the speed to a minimum, maintaining the temperature. Therefore, silence in such refrigerators may mean operation at low speeds, and not a complete stop.
How to distinguish an inverter refrigerator?
Inverter models operate almost silently and do not have the characteristic loud clicks when starting and stopping. The nameplate on the back usually has the mark Inverter or an indication of variable engine speed.
Algorithm for checking the health of equipment
To understand whether your new one is behaving normally Indesit, you need to carry out simple diagnostics. Don't rely solely on hot/cold sensations. Use the outer thermometerby placing it in a glass of water in the center of the middle shelf. This will give an objective picture of what is happening inside.
Check the heating of the condenser (grid at the back or side walls). If the compressor has been humming for 5 hours and the grate remains cold, it means it is broken. If the grate is hot but there is no cold, the capillary tube may be clogged or the refrigerant circulation is faulty refrigerant circulation broken. If the grate is hot but not cold, the capillary tube may be clogged or faulty valve.
Pay attention to the frequency of the cycles. Record the time: how many minutes you work, how many minutes you rest. Write down this information. If after a day of operation the mode has not stabilized (for example, it works for 10 minutes, it stops for 2 minutes), this is a reason to contact the service.
☑️ Refrigerator diagnostics
Possible reasons for continuous operation
If the first day has passed, and the refrigerator Indesit still does not think to turn off, there may be several reasons. The most commonplace is a door that is not tightly closed or is worn out. Warm air from the room constantly gets inside, the temperature sensor detects the heating and does not give a command to stop. seal. Warm air from the room constantly gets inside, the temperature sensor detects the heating and does not give a command to stop.
The second common reason is leakage refrigerant (of freon). The gas could have escaped through a microcrack in the foamed part of the case or at the soldering point. The compressor tries to build up pressure and temperature, working for wear, but physically cannot do this due to a lack of working fluid.
The third reason lies in the electronics. A malfunction thermostat, defrost sensor or control unit may result in the stop signal simply not being sent to the engine. In such cases, it is necessary to replace the failed element.
| Symptom | Probable cause | Necessary actions |
|---|---|---|
| Works >12 hours, no cold | Leakage freon / Clogged | Call a technician to find a leak |
| Often turns on/off | Thermostat is faulty | Replacing the temperature sensor |
| Humming, but not freezes | Compressor malfunction | Diagnostics of the motor and start relay |
| Ice coat in one chamber | Problems with the No Frost system | Checking the defrost heating element or fan |
⚠️ Attention: An independent attempt to refill the refrigerator with freon or replace the compressor without special equipment and a license is prohibited by law and is life-threatening. Entrust the repair to certified specialists.
Recommendations for use after purchase
In order for your Indesit to serve for a long time and work correctly, it is important to follow the operating rules from the first minutes. After transportation, be sure to let the equipment stand in an upright position for at least 3-4 hours (preferably 24 hours) so compressor oil the glass will fall into the crankcase. Switching on immediately after shaking can lead to water hammer and motor breakdown.
Perform the first switching on without food. Let the refrigerator run a full cycle and turn itself off. Only after the appearance of stable cold and a characteristic stop click can the gradual loading of products begin. This will extend the life of the unit.
Regularly check the condition of the rubber seals and the cleanliness of the condenser at the back. Dust on the grill drastically impairs heat transfer, causing the motor to work longer and more often. Simple vacuuming every six months can prevent 30% of breakdowns associated with overheating.