Numbers on the Stinol refrigerator: full decoding for all models (2026)

Have you ever looked at the back wall or control panel of your refrigerator Stinol and seen mysterious numbers there - 1, 2, 3, 4, 5, 7 or even two-digit combinations like E1, F2, H1? These symbols are not just put on by the manufacturer: they encode critical information about operating modes, temperatures, and sometimes about malfunctions. Their incorrect interpretation can lead to spoilage of products, increased energy consumption, or even breakdown of equipment.

In this article we will examine in detail all possible digital designations refrigerators Stinol - from basic models (Stinol 100, 101, 103) to modern ones (Stinol 200, 205). You will learn how correctly set the temperature by the numbers on the regulator, what they mean error codes on the display (if there is one), and why sometimes the refrigerator “freezes” on one number. And also - a unique table of correspondence between numbers and real temperatures in the freezer and refrigerator cameraswhich you will not find in the standard instructions.

We warn you right away: some numbers may mean serious malfunctions (for example, a freon leak or a compressor breakdown). If after reading the article you suspect something is wrong, do not try to repair the equipment yourself. Contact the service center Stinol or a trusted technician.

1. Numbers on a mechanical regulator: what does each position mean

Most refrigerators Stinol of older series (100, 101, 103, 107) are equipped with mechanical temperature controller - a round switch with numbers from 1 to 7 (less often up to 5). Many people mistakenly think that these numbers represent degrees Celsius. In fact, they indicate cooling intensity, and not the exact temperature.

Here's how it works:

• 🔹 1 —minimum power (the “warmest” mode). Suitable for storing fresh vegetables, fruits and drinks. The refrigerator compartment will be about +8…+10°C.
• 🔹 2–3 —standard mode for most products. Temperature: +4…+6°C (optimal for milk, cheeses, sausages).
• 🔹 4–5 —intensive cooling. Needed for hot weather or if the refrigerator is often opened. Temperature: +2…+4°C.
• 🔹 6–7 —maximum cold. Rarely used (for example, for rapid cooling of large volumes of products). In the refrigerator compartment it can be 0…+2°C, in the freezer - up to −24°C.

⚠️ Attention: If you set the regulator to 7 and leave it for a long time, the compressor will work without stopping. This will lead to freezing of food in the refrigerator compartment and increased wear of equipment. The optimal mode for most families is 3.

What happens if you leave the regulator at "7" for a long time?

When operating for a long time at maximum power (position "7") the compressor of the Stinol refrigerator does not turn off for rest, which leads to:

- Formation of a thick layer of ice in the freezer (more than 1 cm per day).

- Refreezing of food in the refrigerator compartment (for example, milk will turn into ice and cucumbers will become soft).

- Increased energy consumption (up to +30% of the norm) and the risk of compressor overheating.

In older models (before 2010), this can trigger thermal protection and breakdown.

2. Numbers on the electronic display: modes and errors

Modern models Stinol (110, 200, 205 series) are equipped electronic displaywhere numbers and alphanumeric codes are displayed. They are divided into three categories:

1. Current temperature (for example, +4 in the refrigerator compartment, −18 in freezer).
2. Specified settings (flashing numbers when changing mode).
3. Error codes (combinations of letters and numbers, for example, E1, F2, H1).

If the display is lit one digit without blinking (for example, 5) - this is current temperature in the refrigerator compartment. If the number is flashing , you are in the setting mode. To change the parameters, use the +/− or Mode (depending on the model).

⚠️ Attention: If the combination appears on the display letters and numbers (for example, E1 or F3) are error code. Do not ignore it! Below we will look at the most common codes for Stinol.

3. data-i="143">: decoding and what to do Stinol: decoding and what to do

Refrigerators Stinol with electronic control can produce errors in the form of alphanumeric codes. Here are the most common ones:

⚠️ Attention: If the code appears on the display E5 or F4 , this may indicate Freon leakageIn this case, the refrigerator cannot be turned on Before repair! Freon is non-toxic, but its leakage leads to loss of cooling performance and the risk of fire when it comes into contact with hot parts.

If you see unknown code on the display (for example, C1, P2), check the instructions for your model. Stinol different years of manufacture may have unique designations. For example, in models Stinol 205 the code L1 means a door lock, and in Stinol 110 a lighting error.

4. Numbers on the back wall or nameplate: model and technical data

On the back wall of the refrigerator Stinol (usually on a metal nameplate) there are numbers and letters like STINOL-103/1-01 or RF-305/200. This is model numberwhich contains important information:

• 📌 First digits (103, 200, 305) — series of the refrigerator. The higher the number, the newer the model.
• 📌 Letters (RF, RT, RK) — type of refrigerator:
  • RF — with freezer below,
  • RT — with a freezer on top,
  • RK — side-by-side (two doors).
• 📌 Last digits (01, 02, 200) — modification (climate class, color, equipment).

For example, the inscription Stinol RF-305/200 is deciphered as follows:

• 🔹 RF — refrigerator with bottom freezer,
• 🔹 305 —model 300 series (released after 2010),
• 🔹 200 — modification with improved thermal insulation (climate class SN-T, operates at +10...+43°C).

⚠️ Attention: If the nameplate indicates climate class N (normal), the refrigerator is not intended for operation in hot climates (above +32°C). Use in such conditions will lead to overheating of the compressor and a reduction in service life.

Also on the back wall can be applied:

• 🔧 Serial number (needed for warranty service),
• ⚡ Power (for example, 120 W),
• ❄️ Climate class (N, SN, ST, T —see explanation below).

Look at the back wall (data plate)

Open the door - sometimes the model is indicated on the side wall inside

Check the warranty card or box (if you have one)

Look at the instructions (first page)

-->

5. Numbers on the freezer: freezing modes

In freezers Stinol (especially in models with No Frost) there are also digital symbols. They can be located:

• 🔘 On a mechanical regulator (numbers 1–7 or Min–Max),
• 📱 On an electronic display (values from −12°C to −24°C).

This is what the numbers on the freezer mean camera:

• 🥶 1 (or −12°C) —defrosting or short-term storage (up to 1 month).
• ❄️ 3 (or −18°C) —standard mode (storage up to 6 months).
• ❄️❄️ 5–6 (or −20…−22°C) —long-term storage (up to 12 months).
• ❄️❄️❄️ 7 (or −24°C) —super freezing (quick freezing of large volumes).

⚠️ Attention: Mode super freezing (7 or −24°C) cannot be used continuously! It is intended for rapid freezing (no more than 24 hours). Long-term operation in this mode leads to:

• 🔋 Increased energy consumption (up to +40%),
• ❄️ Formation of a thick layer of ice (even in models with No Frost),
• 🛠️ Accelerated wear of the compressor.

In models with No Frost (for example, Stinol 200) the numbers on the freezer may flash during:

• 🔄 Automatic defrosting (normal phenomenon, lasts 10–15 minutes),
• ⚠️ Fan malfunctions (requires diagnostics).

6. Numbers on the door seal: production date

Few people pay attention, but to rubber door seal refrigerator Stinol there are also numbers. They are usually printed in the form four-digit code (for example, 0321 or 1218). This is date of manufacture of the seal (not the refrigerator itself!). door seal

• 📅 First two digits - week of the year (from 01 to 52),
• 📅 The last two digits - year (for example, 21 = 2021).

Example: code 0321 means that the seal was made in 3rd week of 2021 (January).

Why know this?

• 🔍 If the seal is older 10 years, it could lose elasticity. This leads to loss of cold i increased energy consumption.
• 🛠️ When replacing the seal, the technician can select an original spare part by date (important for older models).
• 📉 If the refrigerator was purchased recently, but the seal is older than 5 years, it may be relabeled product (used).

⚠️ Attention: If the seal is cracked or does not fit tightly, check it this way: close the door, insert a sheet of paper and try to pull it out. If the paper comes out easily, the seal is worn.

7. Numbers on the compressor: model and power

There are also numbers and letters on the compressor (the black “box” at the back of the refrigerator), for example: DWM 1/6 WZ or QL 120H. This is compressor modelby which you can determine:

• 🔌 Power (for example, 120 W in the model QL 120H),
• 🔄 Refrigerant type (old models work on R12, new ones - on R600a or R134a),
• 🛠️ Compatibility with spare parts (important during repairs).

Here is a breakdown of popular compressors for Stinol:

⚠️ Attention: If the refrigerant is indicated on your compressor R12, it you cannot fill with modern freons (R134a, R600a) without modifying the system! This will lead to compressor breakdown.

Also on the compressor may be marked serial number i production date (similar to the seal). If the compressor is older than the refrigerator, it may have already been changed.

FAQ: Frequently asked questions about the numbers on the refrigerator Stinol

❓ On the regulator of my Stinol the numbers are from 1 to 5, not 7. Is this normal?

Yes, in some models (for example, Stinol 107 or compact refrigerators) the regulator scale is reduced to 5 positions. In this case:

• 1–2 — economical mode (+6…+8°C),
• 3 - optimal mode (+4...+5°C),
• 5 - maximum cooling (+2...+3°C).

The logic is the same: the higher the number, the colder.

❓ The number 8 is lit on the display, but the refrigerator does not freeze. What should I do?

The number 8 on the display Stinol usually means demonstration mode (as in the store) The compressor does not turn on, but on the screen. "beautiful" numbers are displayed. To exit:

1. Press and hold the button Mode (or Super) for 5-10 seconds.
2. If this does not help, unplug the refrigerator for 1 minute.
3. In some models you need to press + and − at the same time.

If after this the refrigerator does not work, the control board may be faulty.

❓ How to reset error E1 on Stinol 200?

The error E1 is related to the refrigerator compartment temperature sensor. Try:

1. Disconnect the refrigerator from the power supply for 10 minutes.
2. Check whether the door is tightly closed (the sensor may be triggered due to warm air).
3. If the error remains, the sensor needs to be replaced (cost ~1500–2500 ₽ including labor).

⚠️ Do not ignore E1! With this error, the refrigerator may incorrectly regulate the temperaturewhich will lead to spoilage of food.

❓ What do the numbers 220–240 V and 50 Hz on the nameplate mean?

This nominal power supply parameters:

• 220–240 V —voltage range at which the refrigerator operates stably.
• 50 Hz —current frequency (standard for Russia).

If the voltage in your network goes beyond these limits (for example, 180 V or 250 V), the refrigerator can:

• 🔌 Not turn on,
• 🛠️ Work intermittently,
• ⚡ Burn out (during power surges).

Solution: use stabilizer voltage (for example, Resanta ASN-1000).

❓ Why are there no numbers on the regulator of my Stinol, only stripes?

Some models (for example Stinol 101 early releases) use numbers instead of numbers horizontal stripes (from 1 to 4). This is an analogue of a digital scale:

• 1 strip = 1–2 (minimum cooling),
• 2 stripes = 3 (optimal mode),
• 4 stripes = 5–6 (maximum cooling).

The logic is the same: the more stripes, the colder.