Purchase of a new one household appliances is always an event accompanied by the expectation of comfort and fresh design in the kitchen. However, before you can enjoy your work of refrigeration equipment, you must correctly complete the unpacking procedure and prepare for the first launch. One of the critical steps, which is often ignored or performed incorrectly, is the removal of special fasteners designed to protect the internal mechanisms during transportation.
Equipment owners Indesit often encounter incomprehensible design elements that seem to be part of the case, but are actually temporary. If you miss the moment of removing them, compressor it may work with overload, and vibrations will lead to premature wear of the unit. In this article we will analyze in detail where to look for these elements, how to safely remove them and why this must be done before turning on the device into the network.
Purpose and operating principle of transportation fastenings
The manufacturing plant uses special transport bolts gaskets for rigid fixation moving units during logistics operations. The main task of these elements is to prevent the shock absorbers from moving under the influence of shocks or shaking along the way. Without such protection, the internal suspension of the motor could receive critical damage even before the goods were delivered to the store. compressor and shock absorbers under the influence of shocks or shaking along the way. Without such protection, the internal motor mount could be critically damaged before the product reaches the store.
The design of the fastenings on the model Indesit is designed to absorb inertial loads as efficiently as possible. When you remove the unit from the box, these elements continue to hold the motor in a static position. This means that when turned on, the vibration from the running motor will not be damped, but will be transmitted directly to the case, causing a strong hum.
⚠️ Attention: Operating the refrigerator with transport locks installed leads to increased noise and the risk of breakage of the cooling system pipes due to the lack of vibration damping.
Understanding the physics of the process helps to understand the importance of dismantling. In normal operation, shock absorbers allow the engine to oscillate freely within certain limits, absorbing movement energy. Rigid fixation deprives the system of this opportunity, turning the entire body into a resonator. That is why the instructions Indesit insist on removing all temporary elements before the first start.
Where the clamps are located in different Indesit models
The location of the elements may vary depending on the series and year of manufacture of yours refrigerator cabinet. Most modern models Indesit use a lower compressor fixation system. You will need access to the back of the unit, where the engine compartment is located.
Sometimes manufacturers hide additional gaskets between the walls of the case and the internal elements to prevent their loss. There are cases when foam inserts are located directly inside of the freezer compartment or the refrigerator compartment, pushing apart the doors or shelves. A careful inspection of the packaging and interior space is required.
It is worth noting that in some budget lines fasteners they can be made in the form of simple wooden blocks or hard cardboard, laid between the compressor and the frame. Their removal does not require tools, but requires care so as not to damage the painted surfaces.
Instructions for the safe dismantling of spacers
The process of removing temporary fasteners requires compliance with a certain sequence of actions to ensure the safety and security of equipment. Before starting work, be sure to disconnect the device from the power supply, if it has already been connected for testing.
☑️ Preparation for dismantling
First, provide free access to the back wall. Move Indesit refrigerator from the wall to a distance that allows you to comfortably work with the lower part of the case. Place a soft cloth or cardboard under the bottom to avoid scratching the floor and to protect the bottom panel of the device.
If you find bolts holding the compressor frame, use a wrench of the appropriate size. Unscrew them carefully, holding the frame itself with your other hand so that it does not fall sharply after removing the fixation. A sudden disruption can damage copper tubing or wiring.
In the case of foam or cardboard gaskets, proceed with caution so as not to leave debris of material inside. Sometimes small pieces can get stuck in the vents or between parts, resulting in strange noises in the future.
Required Tools and Precautions
Although the procedure seems simple, having the right tool makes the task much easier and reduces the risk of damage. You don't need a complex professional kit, but a basic home craftsman kit is a must.
- 🔧 A set of wrenches or sockets for unscrewing frame bolts.
- 🔦 A powerful flashlight for illuminating hard-to-reach places in the engine compartment.
- 🧤 Work gloves to protect your hands from sharp metal edges and dust.
- 🧹 Vacuum cleaner for removing construction dust and small particles of packaging.
Particular attention should be paid to electrical safety. Even if refrigerator has not yet been plugged into a power outlet, make sure that the power cord is not pinched or has any visible damage. Carry out any work inside the engine compartment only with the cable completely disconnected.
What to do if the bolt is rusted or does not unscrew?
If you encounter resistance, do not use excessive force so as not to strip the thread. Treat the joint with a penetrating lubricant (such as WD-40) and leave for 10-15 minutes. After this, try to carefully remove the bolt with a wrench. If the situation does not change, it is better to contact a service center so as not to damage the compressor frame.
Do not forget about physical safety: refrigeration units they have an impressive weight. When moving the device to access the rear wall, involve an assistant to avoid back injuries or equipment falling on your feet.
Typical errors during installation and unpacking
One of the most common mistakes is incomplete removal of packaging materials. Users often remove the outer film and cardboard, but forget to check the internal cavities. As a result, the remaining piece foam can block the operation of the fan or damper.
Another mistake is ignoring the settling time. After transportation, especially in winter, Indesit refrigerator it takes time for acclimatization and oil to drain into the compressor. Turning on the device immediately after bringing it into a warm room can lead to water hammer.
| Error | Consequence | Remedy |
|---|---|---|
| Left transport bolts | Strong vibration, noise, compressor wear | Urgently remove the clamps |
| Start ahead of time | Compressor failure, lack of cold | Wait 4-6 hours |
| Damage to tubes during installation | Leakage of freon, loss of cooling capacity | Call a technician for refilling |
| Uneven installation on the floor | Spontaneous opening of doors, misalignment | Adjustment of support legs |
Neglect to adjust the support legs is also common. If unit is not level, this creates additional load on the door hinges and can simulate problems with the engine mounts due to housing resonance.
Diagnosis of problems after starting
After all transport elements have been removed and the device launched, it is important to monitor its operation in the first hours. A quiet hum of the compressor and periodic gurgling of the refrigerant in the pipes is considered normal.
⚠️ Attention: If you hear knocking, rattling or feel strong vibration of the floor under your feet, immediately stop the device and check that all transport elements have been removed.
Sometimes the source of the noise may not be the source itself. compressor, and touching condenser tubes each other or the housing. During the process of dismantling the fasteners, you can accidentally touch and displace communications. A visual inspection of the rear grille will help identify such contacts.
Pay attention to the stability of operation. If motor turns on and off too often, or works without stopping, this may indicate problems with the thermostat or a leak caused by careless handling during unpacking.
Recommendations for further operation
Correct installation is the key to long service life of your equipment Indesit. After successful removal of the spacers and the first start, it is recommended not to load refrigerator compartment products immediately. Allow the device to reach operating temperature in an empty state.
Regularly check the cleanliness of the rear grille and engine compartment. Dust that accumulates there can impair heat transfer and cause the compressor to work harder. Also save shipping packaging (bolts, foam, boxes) in case you move or need servicing.
Following simple operating rules will allow your refrigerator to serve for decades without loss of efficiency. Remember that most breakdowns at an early stage are associated with installation errors, and not with manufacturing defects.
Do you need to save the removed transport bolts?
Yes, be sure to save all the removed parts, bolts and nuts. Whenever moving or transporting, they must be reinstalled to secure the compressor. Without these bolts, the compressor may come off the shock absorbers during transportation, which will lead to expensive repairs.
What to do if, after removing the bolts, the refrigerator is still noisy?
Check whether the tubes are touching each other or the body. Make sure the refrigerator is level. If the noise persists and resembles a metallic clang, the compressor itself may be damaged or the shock absorbers need to be replaced.
Can the refrigerator be used if the spacers are not removed?
It is strictly not recommended. Working with transport locks installed will lead to rapid compressor failure due to overload and lack of vibration damping. This is not a warranty case.
Where can I find a diagram of fasteners for my Indesit model?
The diagram of the location of transport bolts and fasteners is usually given in the "Installation" or "Installation" section of the operating instructions supplied with the refrigerator. Also, diagrams are often applied to the inside surface of the door or glued to the back wall.