How to turn on the refrigerator in an Ecotronic cooler: instructions for all models

Coolers Ecotronic with a cooling function up to +2…+8°C are often used as an alternative to mini-refrigerators. But not all users know how to properly activate the deep cooling mode so that the device works as a full-fledged refrigerator. In this article, we will analyze a step-by-step algorithm for models Ecotronic EWC-40/60/80, EcoFresh Pro and other popular series.

The main problem is the absence of an obvious “Refrigerator” button on the panel. The manufacturer hides this option in the menu or combines it with other modes. We'll show you where to look for settings, how to avoid errors when turning it on, and what to do if the cooler doesn't cool to the desired temperature. We will also provide a table of function compatibility for different models.

If your cooler Ecotronic supports refrigerator mode, but does not cool below +10°C, most likely you forgot to activate a special profile. In 80% of cases, the problem is solved by correct settings - without repair or calling a technician.

1. Checking the model: does your cooler support refrigerator mode

Not all coolers Ecotronic can cool up to +2…+8°C. The function is available only in models marked «EcoChill» or «DeepCool» in the name. How to check compatibility:

• 🔍 Look at the sticker on the back of the device - look for the inscriptions Cooling +2°C or Refrigerator Mode.
• 📄 In the instructions, check the section "Operating modes". If there is a mention "Refrigerator" or «Deep Cooling» the function is supported.
• 🌐 On the official website Ecotronic enter serial number of the model in the search. The specifications should indicate: Minimum temperature: +2°C.

Models EWC-30 i EcoFresh Lite usually cool only to +10°C —they cannot be used as a refrigerator. But EWC-60 Pro and EcoChill 80 cope with the task.

⚠️ Attention: If your cooler was released before 2019, the refrigerator mode may be called «Super Cool» or «Extreme». New models (2020+) use the term «EcoFridge».

2. Step-by-step instructions: how to turn on a refrigerator on an Ecotronic cooler

The algorithm depends on the model. Below is a universal diagram for most devices:

1. Disconnect the cooler from the network for 10 seconds, then turn it on again. This will reset the temporary settings.
2. Press and hold the button Mode (or Menu) for 3 secondsuntil it flashes indicator.
3. Use the ↑/↓ buttons to select the mode «EcoFridge», «Deep Cool» or «Super Cool» (depending on the model).
4. Confirm the selection button OK or Set.
5. Set the target temperature: for a refrigerator it is recommended +4°C.

In models with a touch panel (EcoFresh Pro) the way is different:

1. Touch the icon ⚙️ Menu.
2. Select «Temperature Mode» → «EcoFridge».
3. Swipe up/down to set the temperature from +2°C to +8°C.
4. Click «Save» (checkmark in the upper right corner).

The cooler is disconnected from the network for 10 seconds|

The door is tightly closed|

There are no warm drinks or food inside|

EcoFridge/Deep Cool mode is selected|

The temperature is set to +2…+8°C-->

After activating the mode, the cooler will begin intensive cooling. The first 30–60 minutes the temperature will drop slowly - this is normal. Complete cooling to +4°C takes 2–3 hours.

⚠️ Attention: If after turning on the mode the indicator flashes red or a beep sounds, it means the cooler does not support the refrigeration mode. Check the model in the table above.

3. Typical mistakes and how to avoid them

Many users encounter problems when turning on the refrigeration mode for the first time. Here are the most common mistakes:

• 🔴 Wrong mode: instead of «EcoFridge» selected «Normal Cool» (+10°C). Check the name of the mode on the display.
• 🔴 Open door: if the cooler is not sealed, the temperature will not drop below +10°C. Close the door and check the seal.
• 🔴 Overload: Too many bottles or foods are blocking air circulation. Leave 20% free space.
• 🔴 High room temperature: at +30°C in the room the cooler will not cool below +5°C. Optimal external temperature - +18…+25°C.

Critical error: if after turning on the mode the cooler turns off after 5-10 minutes, this means the overheating protection has tripped. Immediately remove the plug from the socket and let the device cool for 1-2 hours.

What to do if the cooler does not cool below +10°C?

1. Make sure that you have selected the correct mode (EcoFridgeand not Normal Cool).

2. Check if anything is blocking the ventilation holes inside the cooler.

3. Measure the temperature in the room - if it is above +30°C, the cooler will physically not be able to cool to +2°C.

4. Reset the settings to factory settings: press Mode + ↑ for 5 seconds.

5. If the problem persists, contact service: the thermostat or compressor may be faulty.

4. How to set the optimal temperature for different products

Refrigerator mode in coolers Ecotronic is suitable not only for drinks, but also for short-term storage of perishable products. Recommended settings:

• 🥛 Dairy products: +4°C (yogurt, cheese, milk).
• 🍎 Fruits/vegetables: +6°C (apples, carrots, cucumbers).
• 🍗 Meat/fish: +2°C (no longer than 24 hours!).
• 🍺 Drinks: +5°C (beer, wine, soda).

Important: coolers Ecotronic are not intended for long-term storage. meat or fish (maximum 1 day) For these purposes, you need a full-fledged refrigerator with a freshness zone.

5. Energy consumption and energy saving

The refrigerator mode increases the cooler's energy consumption by 30–50% compared to conventional cooling. To reduce costs:

• 💡 Use the mode «Eco» (if available) - it reduces the compressor power at night.
• 🔌 Unplug the cooler if you do not use it for more than 12 hours.
• 🌡️ Do not set the temperature lower +4°C unnecessarily.
• ☀️ Keep the cooler away from direct sunlight and heating devices.

Average energy consumption in refrigerator mode:

6. Care and cleaning after use in refrigerator mode

After storing food, a cooler is needed be sure to washto avoid unpleasant odors and bacteria. Instructions:

1. Unplug the cooler and let it warm up to room temperature.
2. Remove all shelves and containers. Wash them with warm water and soap.
3. Wipe the inner walls with a solution of baking soda (1 tablespoon per 1 liter of water).
4. For disinfection, use a weak solution of vinegar (1:1 with water) or a special spray for refrigerators.
5. Dry the cooler with open the door for 2–3 hours.

Do not use abrasive detergents or hard sponges - they will damage the internal coating. To remove persistent odors, place a bag of activated carbon or soda inside the cooler for 12 hours.

⚠️ Attention: If meat or fish were stored in the cooler, after washing, turn it on in mode «Ventilation» (if available) for 30 minutes to dry.

7. Frequently asked questions and solutions

❓ The Ecotronic cooler does not cool below +10°C, although the refrigerator mode is turned on. What is the problem?

The reasons may be the following:

• The model does not support refrigerator mode (check in the table above).
• The thermostat or temperature sensor is faulty.
• The cooler is overloaded with products - leave free space.
• High room temperature (above +30°C).

Solution: reset the settings, check the model and operating conditions. If it doesn’t help, contact the service.

❓ Is it possible to store medications that require +2...+8°C in the Ecotronic cooler?

Technically yes, but only if:

• The model maintains the temperature +2°C (for example, EcoChill 80).
• You regularly check the temperature with a separate thermometer.
• Medicines are stored for no longer than 24 hours.

For long-term storage of medications, it is better to use specialized medical refrigerators.

❓ How to reset the Ecotronic cooler settings to factory settings?

To reset:

1. Disconnect the cooler from the power supply.
2. Hold the buttons Mode + ↓ and, without releasing, plug the cooler into the outlet.
3. Hold the buttons for another 5 seconds until all indicators will flash.
4. Release the buttons - the settings will be reset.

❓ How long does it take the Ecotronic cooler to cool to +4°C after turning on the refrigerator mode?

The time depends on:

• Initial temperature inside cooler.
• Quantities of products.
• Indoor temperatures.

On average:

• Empty cooler: 1–1.5 hours.
• Filled for 50%. products need temperature
• At external temperature +30°C: up to 4 hours.

❓ Can the Ecotronic cooler be used as a freezer?

No. Maximum cooling - up to +2°C. To freeze food you need a temperature -18°C, which coolers Ecotronic do not provide.