Modern household climate requires equipment owners to take a careful approach to the initial operation of the equipment. Finist refrigerator is a complex system where proper control of modes directly affects the service life of the compressor and the safety of products. After unpacking and installing the unit on a flat horizontal surface, you must let it stand for at least 4-6 hours before plugging it into the network. This time is required for the oil to drain into the compressor crankcase, which prevents water hammer at start-up.
Primary setting of temperature conditions is a critical step. Factory settings may not suit your current needs or environmental conditions. Intelligent control system allows you to flexibly adjust the climate parameters inside the chambers, however, basic knowledge of the operating principles is necessary for each user. In this guide, we will look at all aspects of the configuration of your device.
⚠️ Attention: If the refrigerator was transported in a lying position, the resting time before first use should be at least 12 hours. Ignoring this rule may lead to compressor failure, which is not a warranty case.
Electronic module and panel control
Most modern models Finist are equipped with an electronic control panel located on the outside of the door. The interface may vary depending on the series, but the operating logic remains the same. Touch buttons or mechanical switches are used to change the operating parameters of the compressor and defrost system. To activate the panel, you often need to press and hold the power button for 3-5 seconds until a beep appears.
The display shows the current temperatures in the refrigerator and freezer compartments. The symbol of flashing numbers indicates the setting mode, allowing the user to change the value using the adjustment buttons. It is important to understand that changing the settings does not take effect immediately, but after the temperature has stabilized, which may take several hours.
Some models are equipped with a rotary control that simplifies navigation through the menu. By turning the knob you select the desired parameter, and with a short press you confirm the choice. This system minimizes the risk of children or pets accidentally changing the settings.
Temperature adjustment in the refrigerator compartment
The optimal temperature in the main compartment should be in the range from +2 to +5 degrees Celsius. It is under these conditions that pathogenic bacteria they reproduce the slowest, and products remain fresh for the longest possible time. To set the desired value, you must press the refrigerator temperature adjustment button (usually indicated as "Fridge" or a snowflake symbol with one star).
Each press changes the value by one degree. The adjustment cycle can go from the minimum value to the maximum and back. Electronic thermostat reads sensor readings and automatically turns the compressor on or off to maintain the set level. If you set the temperature too low, food at the back wall may freeze, which is especially critical for vegetables and fruits.
There is a direct relationship between the fullness of the chamber and the cooling efficiency. An empty refrigerator operates less efficiently because air has a low heat capacity. In this case, the products act as cold accumulators.
☑️ Checking the temperature conditions
Setting the freezer and super freezing
The freezer compartment requires lower temperatures, usually from -18 to -24 degrees Celsius. The super freezing (Super Freeze) mode is designed for rapid cooling of large quantities of fresh food. When this function is activated, the compressor operates continuously, ignoring standard shutdown cycles, which allows you to quickly freeze the product throughout its entire depth, preserving its structure and vitamins.
You can activate the mode through the control panel by pressing the corresponding button. A snowflake-shaped indicator or the inscription “SF” will light up on the display. In most models automatic shutdown occurs after 24-48 hours, or manually by the user.
The use of quick freezing mode is justified when preparing food for the winter or after a large purchase of meat and fish. For daily storage, the standard mode of -18 degrees is sufficient.
⚠️ Attention: Do not load warm or hot foods into the freezer. This causes a sharp jump in temperature, the formation of ice on the evaporator and an increased load on the compressor, which reduces the service life of the equipment.
What happens during long-term operation of super-freezing?
When operating in super-freezing mode for more than 3 days without load, it is possible that already frozen products are overcooled, changing them consistency and excessive energy consumption up to 30%.
Special modes and additional functions
Modern refrigerators Finist are often equipped with additional functions to increase comfort. The "Vacation" (Vacation) mode switches the refrigerator compartment to an economical operating mode with a temperature of about +15 degrees, preventing the appearance of mold and odor while the freezer continues to operate normally. This is an ideal option for long-term absence of owners.
Function "Eco" optimizes the operation of the compressor for minimal energy consumption. In this mode, the temperature may fluctuate slightly more widely, but the food remains safe. There may also be a rapid cooling mode for drinks, which briefly lowers the temperature in the freshness zone.
Some models have a "Zero Freshness" zone, where the temperature is maintained at about 0 degrees and a certain humidity. This is an ideal place to store meat, fish and dairy products before cooking.
Table of recommended storage temperatures
To ensure maximum safety of food, it is important to know under what conditions they are stored best. Below is a table with optimal parameters for various categories of food.
| Product type | Recommended temperature | Shelf life (approximate) | Placement area |
|---|---|---|---|
| Fresh meat/poultry | 0..+2 °C | 1-2 days | Lower shelf / Freshness zone |
| Dairy products | +2..+4 °C | 3-5 days | Middle shelves |
| Vegetables and fruits | +4..+6 °C | 3-7 days | Bottom drawers |
| Ready meals | +2..+5 °C | 1-2 days | Upper shelves |
| Frozen foods | -18 °C and below | up to 12 months. | Freezer compartment |
Violation of the temperature regime leads to accelerated spoilage of products. For example, storing milk at temperatures above +6 degrees can lead to souring in a few hours.
Diagnostics and troubleshooting
During operation, situations may arise when the settings are lost or the refrigerator no longer supports the set mode. If the display lights up alarm indicator (a rapidly flashing red triangle or exclamation mark), this indicates that the temperature in the chamber has risen above the permissible limit. The reason may be a loose door or loading a large volume of warm food.
Sometimes full is required resetting settings to factory settings. To do this, you usually need to hold down a certain combination of buttons (for example, "Temperatrue" and "Mode" at the same time) for 10 seconds. It is better to check the exact combination for your model in the technical documentation, as it may differ. Finist It is better to check the technical documentation, as it may differ.
If after setting the temperature does not stabilize within 24 hours, you may need to check the tightness of the seals or the amount of refrigerant in the system. Self-repair of the cooling circuit is prohibited.
Why does the Finist refrigerator make a lot of noise after setting it up?
After changing the temperature settings, especially when turning on the super-freeze mode, the compressor may go into maximum power mode. This causes increased noise and vibration. Also check whether the refrigerator is level on the floor and whether foreign objects are touching its walls.
How often do you need to defrost a refrigerator with No Frost?
The system No Frost assumes automatic removal of moisture, so defrosting to remove ice is not required. However, sanitary defrosting with washing of internal surfaces is recommended to be carried out 1-2 times a year to maintain hygiene.
What to do if the display goes out after a few seconds?
This is normal behavior to save energy. The display is activated when any button is pressed or the door is opened. If the screen does not light up even when pressed, check the connection of the refrigerator to the network and the condition of the socket.
Is it possible to change the temperature while the compressor is running?
Yes, the electronic control system Finist allows you to change settings in real time. The compressor will adjust its operation in accordance with the new set parameter during the next cycle.
Are the settings lost when the power goes out?
In modern models, the settings memory is stored in a non-volatile module. Once power is restored, the refrigerator will return to the last set values. However, if the shutdown was long, the temperature inside the chambers will increase, and it will take time to restore it.