Push Go function in an Indesit refrigerator: what is it for and how to use it correctly

If you are the owner of a refrigerator Indesit with a system No Frost or combined defrosting, you probably noticed a mysterious button on the control panel Push Go. Many users have ignored it for years, considering it unnecessary, and some are afraid to accidentally press it for fear of resetting the settings. In fact, this function solves a specific problem - and if used correctly, it can save your time and energy.

In this article we will examine in detail why do you need a Push Go button in refrigerators Indesithow it works in different models (for example, Indesit ITF 118, Indesit BIAA 13 or Indesit DF 5200), and in which situations it should be activated. You will also learn how it differs Push Go from standard defrosting and why it cannot be used too often. For clarity, we will provide step-by-step instructions with a photo of the control panel and a table of compatibility of functions in popular series of refrigerators of the brand.

Spoiler: if your refrigerator began to freeze worse, and ice appeared on the back wall of the freezer, most likely, the problem is solved by this button. But there are nuances that the manufacturer is silent about in the instructions.

What is the Push Go function and how does it work

The button Push Go (sometimes designated as PUSH&GO or simply GO) is accelerated mode of forced defrosting of the evaporator in refrigerators with the No Frost or Low Frost system. Unlike complete manual defrosting, it does not require disconnecting the device from the network and unloading the products, but at the same time effectively removes ice from key elements of the cooling system.

Technically, the function works like this:

• 🔄 It is activated intensive fan modewhich blows the evaporator with warm air from the main compartment.
• ❄️ Ice melting is accelerated due to short-term shutdown of the compressor (for 10–30 minutes, depending on model).
• 💧 The moisture flows into a special tray, where it evaporates naturally.
• ⚡ After the cycle is completed, the refrigerator automatically returns to normal mode.

It is important to understand that Push Go is not a replacement for complete defrosting, but rather “emergency assistance” to the system. It cleans only evaporator (the main element of No Frost), but does not remove ice from the walls of the chambers or door seals. Therefore, it should be used only at the first signs of icing, and not as a regular procedure.

Which Indesit models have a Push Go button

Function Push Go found mainly in refrigerators Indesit with system No Frost or Low Frost, released after 2015. However, there are exceptions: some models with drip defrosting (for example, Indesit TS 16) are also equipped with this button, but there it works differently - it triggers accelerated melting of ice in the drainage system.

Here are the main series where you will find Push Go:

• 🍁 Indesit ITF (two-chamber No Frost, for example, ITF 118, ITF 120).
• ❄️ Indesit BIAA and BIAA 13 (freezers with No Frost).
• 🧊 Indesit DF 4180, DF 5200 (combined models with a freshness zone).
• 🔄 Indesit EWD (models with electronic control and display).

To accurately determine whether Push Go your model, check:

1. 📄 Instructions (section “Functions” or “Control”)
2. 🔍 Panel controls: the button can be labeled as PUSH&GO, GO or indicated by a snowflake with an arrow.
3. 🌐 Official website Indesit (enter the model in the catalog search).

How to distinguish No Frost from Low Frost?

In refrigerators with No Frost the evaporator is hidden behind the back panel, and the ice is formed only on it. Low Frost The evaporator is located around the perimeter of the chamber, so frost can also appear on the walls. The Push Go function in Low Frost is less effective and requires more frequent use.

When you need to press Push Go: 5 obvious signs

The manufacturer recommends using Push Go "as needed", but does not specify which symptoms should alert you. In practice, the button should be pressed in the following cases:

⚠️ Attention: If after pressing Push Go the problem has not disappeared (for example, the ice remains, but the refrigerator continues to make noise), this may indicate malfunction of the heating element. defrost or defrost sensorIn this case, diagnostics from the service center is required.

Step-by-step instructions: how to use Push Go correctly

The function activation algorithm depends on the refrigerator model, but the general scheme looks like this:

1. 🔌 Make sure that the refrigerator is connected to the network (the function does not work when disabled power supply).
2. 📱 Find the Push Go button:
   • In models with mechanical control (for example, Indesit ITF 118) this is a separate button next to the temperature control.
   • In refrigerators with electronic display (for example, Indesit EWD 6140), the function can be hidden in the menu - press Menu → Service → Push Go.

🔘 Press and hold the button for 3-5 secondsuntil the indicator lights up (usually yellow or green). On some models, a beep will sound.

⏳ Wait for the loop to complete (10 to 40 minutes). data-i="156">Wait for the cycle to complete

• The compressor may turn off.
• The fan will operate at increased speed.
• The display may flash GO or DEF.
• 🔄 Check the result: open the freezer and inspect the back wall. The ice on the evaporator should melt.

Close the refrigerator doors|Make sure that food is not blocking the ventilation holes|Turn off the "Super Freeze" mode (if enabled)|Do not open the compartments during cycle time|Check that the refrigerator is level (without distortions)-->

⚠️ Attention: Do not press Push Go more than once a week - this can lead to compressor overload a reduction in the service life of the refrigerator. If ice forms too quickly, check:

• 🚪 The tightness of the door seal.
• 🔌 Mains voltage stability (surges can disrupt operation defrosting).
• 🧊 Correct loading of products (do they not block the ventilation grilles).

How does Push Go differ from complete defrosting

Many users confuse Push Go with classic defrosting, but there are fundamental differences between them differences:

Parameter	Push Go	Full defrosting
🕒 Procedure time	10–40 minutes	4–12 hours
⚡ Energy consumption	Low (only the fan works)	High (the compressor is turned off, the ice melts naturally)
🧊 Removing ice	Only with evaporator	From all surfaces
🍗 Necessity to unload products	Not required	Required
🔧 Frequency of use	1 time every 1-3 months	1-2 times a year

Push Go convenient for preventive cleaningwhen ice has just begun to form. Complete defrosting is needed in advanced cases - for example, if ice more than 5 mm thick has covered the chamber walls or the door seal. Also Push Go useless for:

• 🦠 Odor in the refrigerator (requires washing with detergent).
• 🔧 Breakage of the defrosting heating element (needs repair).
• 🧊 Icing of the drainage hole (must be cleaned manually).

Common mistakes when using Push Go

Despite the simplicity of the function, many users make mistakes that lead to the opposite effect - increased ice build-up or even breakdown. Here's what you can't do:

1. 🚫 Press the button with the door open. In this case, warm air from the room will enter the chamber, and the ice will not melt, but will only become denser.
2. ⏳ Interrupt the cycle (for example, unplugging the refrigerator from the outlet). This can lead to icing of the drainage system.
3. ❄️ Use Push Go with a thick layer of ice (more than 1 cm). The function is designed for thin ice - in advanced cases it will only worsen the situation.
4. 🔌 Activate the function immediately after turning on the refrigerator. The compressor must first enter operating mode (wait 1–2 hours).

⚠️ Attention: In refrigerators Indesit s inverter compressor (for example, Indesit EWD 8140) frequent use Push Go may disrupt the system operation algorithm. In such models, the function should be used no more than once every 2 months.

What to do if Push Go does not work

If after pressing the button nothing happens (the indicator does not light up, you cannot hear the fan working), check the following:

1. 🔌 Power: make sure that the refrigerator is plugged in and on other indicators are lit.
2. 🔘 Button locking: some models (for example, Indesit EWD 6140) have a mode Child Lock, which disables all buttons. To remove the lock, hold the button Lock 3 seconds.
3. 📱 Electronic module: if the display does not respond to presses, a firmware failure may occur. Try unplugging the refrigerator for 10 minutes, then turning it on again.
4. 🔧 Button malfunction: if the indicators are on, but the function is not activated, the contacts may have oxidized or the microswitch may be broken. In this case, the control panel needs to be replaced.

If the refrigerator responds to pressing (the indicator lights up), but the ice does not melt, the reasons may be more serious:

• 🔥 The defrost heating element has burned out —check it with a multimeter (resistance should be 200–500 Ohms).
• 🌡️ The defrost sensor has failed —in this case, the compressor will work without stopping.
• 💨 Stuck fan —listen to see if you can hear the noise of its operation during the cycle.

⚠️ Attention: If after diagnostics a malfunction is revealed, do not try to repair the refrigerator yourself. In models Indesit with electronic control (for example, EWD 8140), incorrect connection of sensors can lead to board failure and expensive repairs.

FAQ: Frequently asked questions about the Push Go function

Can Push Go be used in a refrigerator with a drip system?

In most models with drip defrosting (for example, Indesit TS 16the button Push Go works differently - it starts accelerated Ice melts in the drainage system but does not clean the evaporator. The efficiency is lower than in No Frost, but the function is safe to use.

How much electricity does Push Go consume?

In one cycle (30-40 minutes), the refrigerator consumes about 0.05–0.1 kWh - the same amount as a regular light bulb in 5 hours. This is 10 times less than with complete defrosting.

Why did a smell appear in the refrigerator after Push Go?

This is normal: when the ice melts from the evaporator, old odors may be released. Air the chambers for 1–2 hours, then wipe the walls with a soda solution (1 tablespoon per 1 liter of water).

Is it possible to press Push Go immediately after purchasing a refrigerator?

No, it's pointless. The function is only needed when ice appears. In a new refrigerator, it should be used no earlier than after 3-6 months of operation (if signs of icing appear).

What will happen if you press Push Go when the refrigerator is empty?

Nothing dangerous: the cycle will proceed as normal, but faster (since there is no need to cool the food). However, frequent “idle” starts can reduce the life of the fan.