The search for the exact designation of a household appliance often turns into a real test, especially when an urgent order of spare parts or issuance of a warranty card is required. Owners of Belarusian-made equipment are often faced with a situation where they urgently need to find serial number, but the stickers seem invisible or have worn off over time. Correct identification of the modification is critically important, since the compatibility of compressors, thermostats and electronic control modules depends on it.
In this article we will analyze in detail all the possible locations of identification plates on various series of units Atlant. You will learn the difference between a nameplate and an energy efficiency sticker, and learn how to read the encrypted information printed by the manufacturer. Understanding the markings will allow you to avoid mistakes when ordering components and correctly interpret the technical characteristics of your device.
It is worth noting that the location of information stickers may vary depending on the year of manufacture and the specific product line. Some models have hidden ones that are not noticeable upon first inspection. We will consider both classic placement options and less obvious places where the factory code can be duplicated factory code.
The main locations of identification stickers
The first and most obvious place to look for information about the device is the inner surface of the cameras. Manufacturers of household appliances usually place nameplate in places protected from direct mechanical impact and temperature changes. In most refrigerators Atlant the nameplate is glued to the side wall of the refrigerator compartment, closer to the upper or lower corner.
If there is nothing on the side wall, carefully inspect the back inner wall, sometimes the label is hidden behind the shelves or containers for vegetables. It is important not to confuse the main technical label with the refrigerant label or energy efficiency label, as they may contain different information. The required serial number must be clearly printed and contain an alphanumeric code.
In some two-chamber models, the information is duplicated on the inside of the refrigerator door. However, you should be careful: the sticker on the door is often decorative or contains only brief information, while the main one label with a full registration certificate is located deeper in the body. Always check several places to ensure that the data read is correct.
⚠️ Attention: Never try to forcefully remove the sticker if it is firmly attached. This can damage the plastic casing of the chamber, and restoration of the integrity of the surface will be required for the tightness of the insulation.
Searching for a nameplate on the outside of the housing
When internal searches do not produce results, you need to move on to inspecting the external surfaces of the unit. The classic place for placing technical documentation for many manufacturers, including Atlantis the rear wall of the case. There, in the area of the engine compartment, a metal plate or a durable sticker is often attached, containing all the necessary data.
Getting to the back wall can be difficult if the refrigerator is located close to the wall. In this case, you will need to carefully move the equipment, taking precautions so as not to damage the flooring or ventilation system. On the back panel device model usually indicated in large font next to the factory logo.
It is also worth checking the side ends of the case, although this is less common in modern models. Sometimes manufacturers leave markings on the top of the cabinet, especially in built-in series, where access to the internal walls is limited by the design of the kitchen unit. If you find several stickers, give priority to the one that looks the most official and contains a barcode.
Please note that the information on the outside can be laser engraved or embossed, which makes it more durable. This is especially true for industrial series or models intended for operation in harsh conditions. Factory code in this case, it will be stamped directly on the metal.
Specific placement in built-in models
It can be more difficult for owners of built-in equipment to find information about the device in total, since access to the building is limited by furniture facades. In such models Atlant nameplate is most often placed at the end of the door or on the inner wall, which becomes visible only when the sash is fully opened.
Sometimes manufacturers place the product passport on the base strip or on the inside of the decorative panel. If the refrigerator is already installed in a niche, you may have to partially dismantle the facade or remove the lower ventilation grille to see the markings. This is a labor-intensive process, so it is better to look for the sticker during the initial installation.
Saving paper documents in the case of built-in appliances plays a critical role, since physical access to the marking is difficult.
⚠️ Attention: When dismantling the facades of a built-in refrigerator, be careful with the hinges. Improper door removal can disrupt the geometry of the hinge and lead to a loose seal.
Deciphering the serial number and modifications
After you have found the sticker, you will be presented with a set of numbers and letters, which may seem like a meaningless set of symbols. However, for engineers and service centers, this is a code that tells the story of the creation of a specific piece of equipment. The refrigerator model is usually highlighted in bold and has a format, for example, XM 4008-000.
The first letters indicate the type of device (XM - refrigerator-freezer), the following numbers indicate dimensions and volume of chambers. The last digits in the modification code indicate the color of the case, the type of control and the presence of additional functions, such as a freshness zone or display. Understanding this structure helps to quickly determine the compatibility of spare parts.
Special attention should be paid to the serial number, which is often located under the barcode. It is unique to each unit produced and is used to track production date and factory line. It is by this number that service centers check the status of warranty service.
Below is a table that helps to decipher the main designations in the labeling of refrigerators Atlant:
| Designation in the code | Meaning | Example |
|---|---|---|
| HM | Refrigerator-freezer | XM 4624 |
| MX | Freezer (cabinet) | MX 2835 |
| Last 3 digits | Color and version code | 000 (white), 010 (silver) |
| Serial number | Unique product ID | 5201234 |
What does the "K" code at the end of the model mean?
The presence of the letter "K" or similar symbols at the end of the model range often indicates the use of a specific type of refrigerant or compliance with a certain energy efficiency class adopted in the year of manufacture.
Differences markings in old and new series
Equipment released ten years ago and modern models Atlant may differ significantly in the method of marking. Old Soviet and post-Soviet models used metal plates attached with screws or rivets. They were highly durable, but over time they could oxidize or lose readability.
Modern units are equipped with self-adhesive polymer labels. They are more informative, often contain QR codes for quick access to the manufacturer’s website, but are less resistant to abrasion. If you are the owner of an old model, look for an engraving on the metal; if you own a new model, look for a neat sticker with a glossy finish.
The encoding logic has also changed. In the new series the model range has become more complex, including designations for inverter compressors