Faced with the need for repairs, purchasing spare parts, or simply wanting to know the exact technical characteristics of their unit, every owner wonders where to find the specific designation of the device. Atlant refrigerator model is not easy a set of numbers, but encoded information about the manufacturer, type of equipment, number of cameras, dimensions and even year of manufacture. Knowing the full code is necessary to select the correct filter, thermostat or compressor, since externally similar units can have completely different internal structures.
Most often this information is hidden from view in everyday life, as it is located in places that are not noticeable during normal use. However, if you need to call a specialist or order a part through an online store, you cannot do without it. Errors in one number can result in the purchased part not physically falling into place. In this article we will analyze in detail all possible locations of identification plates. full factory index can't get by. Errors in one number can result in the purchased part not physically falling into place. In this article we will analyze in detail all possible locations for identification plates.
It is important to understand that the Belarusian Atlant plant has been producing equipment for several decades, and the location of the marking elements has changed depending on the year of production. If your refrigerator was purchased recently, there will be one nameplate, but if it is a device from the 90s or early 2000s, the search may take longer. We will consider all options so that you are guaranteed to find the data you need.
The main location of the nameplate
The very first place where technical data searchers should look is inner wall of the refrigerator compartment. In the vast majority of modern and relatively new models (released after 2005-2010), an aluminum or plastic plate with an engraving or seal is fixed there. Usually it is located on the left side wall, approximately at the level of the middle shelf or slightly higher.
Sometimes manufacturers place information on the inside surface of the refrigerator compartment door. To see the nameplate, you need to open the door and carefully examine the end part or the inner plane of the plastic. On older models, where the plastic may have yellowed or become scratched, the lettering may be difficult to see without good lighting. Use your phone's flashlight to illuminate the surface from different angles - the engraving is often only visible in reflected light.
⚠️ Warning: Never try to pick or peel off the nameplate. This is the main document of your unit, and if it is missing, service centers may refuse warranty service or make it difficult to select spare parts.
If there is nothing on the side wall, check the space above the top shelf, closer to the ceiling of the chamber. In some series two-chamber refrigerators engineers placed the technical data sheet in the upper part to avoid damage to the label when loading products onto the lower tiers. It is also worth inspecting the lower part of the chamber, near the floor, although this is a less common place.
Alternative places to look for markings
There are times when the inner chamber is empty, or the plate was accidentally damaged during cleaning. Then rear wall of the cabinetcomes to the rescue. This is a classic place to display technical information on old appliances. To inspect this area, you will most likely have to move the refrigerator away from the wall.
On the back metal panel, often in the top or middle part, there may be a paper label glued to it or data stamped directly into the metal. Be careful: the back wall is where the condenser (grid) is located, which can be hot if the refrigerator has just been running. Allow equipment to cool before touching metal, or use gloves.
Another place that is often forgotten is basement part or the bottom perimeter of the doorway. In some models, especially built-in series or refrigerators with the No Frost system, the sticker is hidden at the bottom so that it does not become an eyesore. It is also worth looking at the technical data sheet that came with the purchase, although over the years of operation this document is often lost.
If you are buying a used refrigerator and there are no documents, and the sticker inside has worn off, inspect the niche for the lighting lamp. Sometimes, in very rare cases, service information is duplicated next to the light bulb socket, although this is the exception rather than the rule for the Atlant brand.
Deciphering the Atlant refrigerator model code
Having found the nameplate, you will see a long set of numbers and letters. This is not a random set of characters, but a strictly structured factory indexUnderstanding the logic behind its construction will help you learn more about your refrigerator than just its name. The code usually looks like a combination of letters and numbers, for example, MXM-1704-01.
The first letters indicate the brand and type of refrigerator. “MXM” means “Minsk Refrigerator Freezer” (two-chamber), “MH” is a single-chamber refrigerator, “M” is a freezer. The following numbers indicate the series and design features. For example, numbers may indicate the presence of a No Frost system or type of control (mechanical or electronic).
At the end of the code, a modification is often indicated through a dash, which may indicate the color of the case, energy consumption class or country of destination (export model). Knowing this structure, you will be able to distinguish the original model from its modification, which is critically important when searching for compatible parts.
What do the letters at the beginning of the code mean?
MHM is a two-chamber refrigerator with one compressor. MHM 18... is a two-chamber with two compressors. M - freezer (chest or cabinet). K - refrigerated cabinet (single-chamber).
It is worth noting that over the years the plant has changed the coding system. Models released in the 90s have one designation structure, and modern series, such as Atlant Optimum or Style, may be labeled differently. Therefore, when deciphering, always take into account the approximate age of the equipment.
Table: Structure of designations in different series
For ease of perception of information, we have systematized the main designations that can be found on nameplates. This table will help you quickly navigate the types of equipment produced by the Minsk plant.
| Code prefix | Type of equipment | Description of features |
|---|---|---|
| MHM | Double-chamber | One compressor, common control system |
| MHM (18xx) | Two-chamber | Two compressors, independent control of chambers |
| M | Freezer | Single-chamber freezer cabinet or chest |
| MX | Refrigerator | Single-chamber refrigerator with freezer inside |
| KSh | Refrigerator cabinet | Professional or specialized equipment |
Using this table, you can easily determine which category your unit belongs to. This is especially useful if you are looking for spare parts in catalogs where equipment is sorted precisely by these prefixes. For example, a compressor for a series MHM may differ in power and starting characteristics from a compressor for a series M.
Please note that in new series there may be letter indices indicating design or special functions such as zone freshness or display on the door. These nuances also affect the selection of electronic control boards.
Determining the production date by serial number
Another important question that owners often have: how to find out the year of manufacture? This information is not always obvious, but it is encoded in serial number (S/N), which is usually located next to the model. The serial number is a unique identifier of a specific instance, in contrast to the model, which is the same for the entire batch.
In older models (before 2010-2012), the year of manufacture could often be determined by the first digits of the serial number or by a separate “Date of Manufacture” field. However, in modern conditions, the plant has switched to more complex encoding systems, where the date is “hardwired” inside a sequence of characters.
There is a common method of decoding using the first digits of the serial number, but it does not work for all years. For example, if a number starts with 9, it could mean 2009 or 2019, depending on the context and decade. A more accurate way is to use official decoding tables, which are periodically updated by the manufacturer.
⚠️ Attention: Information about the production date may be critical for determining the service life of the compressor. If you are buying used equipment, check the actual age with the one stated by the seller using the serial number.
If you cannot decipher the numbers yourself, contact an authorized service center. Internal database specialists will be able to tell exactly when your Atlant refrigerator came off the assembly line, simply by the named code.
☑️ Check before ordering spare parts
What to do if the nameplate is damaged or missing
The situation when the data plate is lost, torn off by the previous owners or has become unusable due to moisture and corrosion is not uncommon. In this case, there is no need to panic, although the identification task becomes more complicated. You will have to use the deductive method and visual comparison.
The first thing to do is measure overall dimensions the refrigerator: height, width and depth. These parameters are key to narrowing down your search. Knowing the exact dimensions (for example, 145 cm height, 60 cm width), you can find the corresponding series in the manufacturer’s catalogs.
The second step is a detailed inspection of the internal structure. Pay attention to:
- 🧊 Number and location of shelves (glass or lattice).
- ❄️ Type of freezer (open, with a door, drawers or shelves).
- 💡 Location of the lighting lamp and regulator temperature.
- 🎛️ Availability of a display or additional buttons on the case.
With this data, you can contact specialized forums or support groups, where experienced users and technicians will help you recognize the model from a photograph. You can also compare your unit with catalog images on the official website, leafing through the archives of past years.
Common mistakes when searching for a model
Many users make typical mistakes that only delay the process. One of the most common is an attempt to find a model on warranty card or a receipt. Often sellers write there an abbreviated name or internal article number of the store, which does not coincide with the factory index on the nameplate.
Another mistake is confusion between the model of the refrigerator and the model of the compressor. The compressor (motor) that hums from behind also has a sticker with technical data. However, these are data from the engine, not from the entire refrigerator. When ordering spare parts by compressor number, you risk making a mistake, since different motors could be installed in the same refrigerator model in different years.
Also, you should not rely on the series name written in large letters on the front panel (for example, Optimum, Style, Classic). These are marketing names and are not an exact technical identifier. To order spare parts, you need a digital code.
Be careful and double-check the information. A correctly identified model is the key to the fact that your refrigerator will work properly after repair, and the new parts will fit like a glove.
FAQ: Frequently asked questions
Is it possible to find out the Atlant refrigerator model on the Internet without access to equipment?
Unfortunately, remotely, without visual inspection of the nameplate or knowledge of the exact dimensions and internal features, it is impossible to recognize the model. Serial numbers are not linked to public databases by address or last name of the owner for reasons of confidentiality.
What to do if the code on the sticker is erased and cannot be read?
Try using side lighting with a flashlight at an acute angle - the relief of the letters may appear. If this does not help, you will have to determine the model by dimensions, photos of the internal contents and appearance, turning to catalogs or specialists.
Where is the serial number if there is no sticker inside?
In rare cases, when there is no sticker inside, duplicate information may be on the back wall of the case (you need to move the refrigerator) or in the technical data sheet of the product, if it is preserved.
Does the year of manufacture affect the selection of spare parts for Atlant?
Yes, it does. Over the years, the plant could change suppliers of components (compressors, thermostats, lampshades). Even for the same model, different parts could be used in different years of production, so the year of production is important.
Is it possible to restore a lost nameplate?
Officially, the plant does not restore nameplates. However, service centers can make a duplicate based on data from the internal database if you prove ownership, but this is a paid and not always available service.