Rehanging the Indesit refrigerator door: instructions with photos, diagrams and life hacks

Hanging the refrigerator door Indesit is a task that almost every owner faces sooner or later. The reasons may be different: inconvenient opening due to the layout of the kitchen, a change in the arrangement of furniture, or a banal desire to refresh the interior. Fortunately, most models Indesit (with the exception of some series with electronic control) support this option. But before you take up a screwdriver, it’s worth understanding the nuances: not all doors are hung equally, and mistakes can lead to leakage or broken hinges.

In this article we will analyze the process step by step —from preparing tools to final adjustment, taking into account the features of popular models (Indesit BIA 18, Indesit DF 4180, Indesit ITF 118) and Let's warn you against common mistakes. You will also learn when it is better to entrust the work to a specialist, and when you can do it yourself in 30–60 minutes.

⚠️ Important: If your refrigerator is under warranty, hanging the door with your own hands can void it. Check this point with the service center Indesit before starting work.

1. Preparation: tools and conditions

Before removing the door, make sure you have everything you need. Most tools can be found in the home arsenal, but some models Indesit may require specific keys.

• 🔧 Screwdrivers: Phillips (PH2) and flat (3-5 mm) - for most hinges.
• 🔨 Wrench: usually 10 or 13 mm (depending on the model).
• 📏 Level: to check the vertical position after installation.
• 🧲 Magnet or tape: to fix the door during work.
• 🧴 Silicone grease: for processing hinges after rehanging.

Also prepare the workspace:

• 🚪 Clear the passage to the refrigerator - the door will have to be removed completely.
• 🔌 Turn off the power (just unplug the plug from the socket).
• 🧊 Remove all products from the door shelves or place them in the main chamber.
• 📸 Take a photo of the location of the hinges and fasteners - this will help with reassembly.

⚠️ Attention: If the refrigerator Indesit with the system No Frost, after rehanging the door, additional adjustment of the sensors may be required. In some models (for example Indesit ITF 118 W), the door closing sensor is located asymmetrically - it will also have to be reconfigured.

2. We determine the type of door fastening: diagrams for different models

Refrigerators Indesit use three main types of door fastenings:

1. Standard bolted hinges (the most common option).
2. Hinges with locks (found in models after 2018).
3. Hidden hinges (rare, usually in premium series).

To understand what type your model has, inspect the top and bottom hinges:

• 🔍 If bolts with a wrench head are visible, these are standard option.
• 🔍 If the bolts are hidden under decorative plugs, these are hinges with clamps.
• 🔍 If the fastenings are not visible at all, most likely hidden hinges, and you can’t do without a diagram from the manufacturer.

Below is a table with examples of models and type of fastenings:

💡 Tip: If you are not sure about the type of fastening, find the instructions for your model on the website Indesit (enter the serial number of the refrigerator in the search). As a last resort, take a photo of the hinges and show it to the consultant at the spare parts store - he will tell you what tools you will need.

Where can I find the serial number of the Indesit refrigerator?

The serial number is usually located on a sticker inside the refrigerator compartment (on the left on the wall) or on the back wall of the case. It begins with letters IND or ITfollowed by numbers. If the sticker has worn off, try to find the number in the warranty card or on the box (if you still have it).

3. Step-by-step instructions: remove and rehang the door

Let's consider the process using the example of a model with standard hinges (for example, Indesit BIA 18). For other types of fastenings, the steps will be similar, but adjusted for design features.

Disconnected the refrigerator from the mains

Freed the door shelves

Prepared the tools

Took a picture of the location of the loops -->

Step 1: Remove the top loop

1. Open the refrigerator door 90 degrees and support it (for example, with a chair or an assistant).

2. Remove the decorative hinge cover (if any) - it usually snaps on or is secured with one bolt.

3. Unscrew the bolts securing the hinge to the refrigerator body (usually 2-3 pieces). Do not unscrew the bolts completely - loosen them enough so that the hinge comes off the axle.

4. Carefully remove the door from the top hinge and place it on a soft surface (for example, a towel).

Step 2: Remove the bottom hinge

1. Turn the door over so that the bottom hinge is accessible.

2. Unscrew the bolts securing the lower hinge to the door (usually 1-2 bolts).

3. Remove the loop and set it aside.

Step 3: Reverse the loops to the other side

1. On the opposite side of the refrigerator body, find the technological holes for the hinges (they are usually closed with plugs).

2. Remove the plugs and install the hinges in a mirror image:

• The upper hinge goes to the left side (if the door was on the right).
• The lower hinge goes to the right side.

3. Secure the hinges with bolts, but do not tighten them completely - first you need to adjust the position of the door.

Step 4: Install the door back

1. Lift the door and put it on the lower hinge.

2. Align the top hinge with the holes and secure with bolts.

3. Check that the door opens smoothly and does not cling to the body.

⚠️ Attention: If the door is after installation does not fit tightly to the seal, it needs to be adjusted. To do this, loosen the hinge bolts and slightly move the door in the desired direction, then tighten the fastenings again.

4. Adjusting the door after rehanging

Even if the door is in place, this is not a guarantee of tightness. Check its position:

• 📏 Use a level to make sure that the door hangs vertically.
• 🔍 Look at the gaps between the door and the body - they should be the same around the entire perimeter.
• 🧊 Do a test with a sheet of paper: squeeze it between the seal and the body. If the sheet falls out, the tightness is broken.

If the door sags or does not fit tightly:

1. Loosen the bolts of the upper hinge and adjust the position of the door vertically.
2. If the problem is in the lower part, tighten or loosen the bolts of the lower hinge.
3. If necessary, adjust the position of the seal (in some models it is secured with latches).

💡 Life hack: If the seal is deformed, try restoring its shape using a hair dryer. Heat the rubber with warm air (not higher than 60°C) and carefully straighten it with your hands. After cooling, the seal will return to its original state.

5. Features of hanging the door in models with No Frost

Refrigerators Indesit with the system No Frost (for example, Indesit DF 5200) have additional nuances:

• 🌬️ Ventilation holes in the door should remain open after rehanging.
• 🔧 The door closing sensor may be located asymmetrically - it will have to be reconfigured or reinstalled.
• ⚙️ In some models, you need to reconfigure the electronic control unit (for example, reset the error dOOr on the display).

📌 Instructions for models with No Frost:

1. After hanging the door, turn on the refrigerator and wait until it returns to operating mode (usually 1-2 hours).
2. If an error appears on the display, press and hold the button Super Cool (or Fast Freeze) for 5 seconds to reset.
3. Check that the ventilation grilles are not blocked by the seal.

⚠️ Attention: In refrigerators Indesit with electronic control (for example, Indesit BIAA 13) after reversing the door, it may sensor calibration is required. If you are not confident in your abilities, it is better to call a specialist.

6. Typical mistakes and how to avoid them

Even experienced craftsmen sometimes make mistakes when hanging a door. Here are the most common:

• 🔩 Tightening the bolts: This can lead to deformation of the hinges or cracks in the plastic case. Tighten the bolts crosswisedistributing the force evenly.
• 🚪 Incorrect position of the seal: If you twist it, the door will not be airtight. Before removing the door, take a photo of how the seal lies.
• ⚡ Forget to turn off the power: although this is not life-threatening, the refrigerator may turn on during work and interfere.
• 🔧 Use inappropriate tools: for example, instead of the key by 10 mm they take 13 mm, which causes the thread to break.

💡 Tip: If after rehanging the door begins to close with a bang, check whether it is warped. Most often, the problem is solved by adjusting the top hinge.

⚠️ Attention: If the refrigerator Indesit s two compressors (for example, Indesit TIA 22), after re-hanging the door, it may be necessary to reconfigure the cooling system. In this case, it is better to contact a service center.

7. When is it better to call a professional: 5 signs

Despite the apparent simplicity, there are situations when it is better to entrust the door hanging to a professional:

• 🔧 If the hinges hidden type require disassembling the case.
• ⚙️ If the refrigerator is with electronic control and after rehanging, errors appear on the display.
• 🚪 If the door two-chamber and synchronous adjustment of both is required sections.
• 🔨 If, when trying to remove the hinges the thread has broken or the body is cracked.
• 📄 If the refrigerator is under warranty and you are not want to lose it.

The cost of the service for re-hanging the door in service centers Indesit ranges from 1,500 to 3,000 rubles (depending on the model and region). It's not that expensive, considering the risks of damaging the refrigerator during self-repair.

💡 How to choose a technician:

• Check reviews of the service center on Yandex.Maps or 2GIS.
• Check whether the technician has experience working specifically with refrigerators Indesit.
• Ask if a guarantee is provided for the work performed.

Frequently asked questions

Is it possible to hang the door on the refrigerator Indesit with an electronic display?

Yes, but after re-hanging, errors on the display may need to be reset. In most models, this requires pressing and holding the Super Cool or Fast Freeze button for 5-10 seconds. If the error does not reset, contact the service center.

How long does it take to rehang the door?

On average, the process takes from 30 minutes to 1.5 hours, depending on the model and experience. The most time is spent on adjusting the door after installation.

Is it necessary to defrost the refrigerator before hanging the door?

No, it is not necessary to defrost it. It is enough to unplug the refrigerator and remove food from the door shelves. However, if the seal is frozen to the body, it is better to carefully separate it so as not to damage it when removing the door.

What to do if the door does not close after rehanging?

Most likely, the problem is in the adjustment of the hinges or the seal. Try:

1. Loosen the hinge bolts and level the door.
2. Check whether the shelves or drawers inside the refrigerator are in the way.
3. Heat the seal with a hairdryer (temperature no higher than 60°C) and straighten it.

If all else fails, the hinges may be deformed - they will have to be replaced.

Is it possible to hang the door on the freezer separately?

Yes, but the process is more complicated than with the main door. In two-compartment refrigerators Indesit the freezer compartment often has separate hinges, and their adjustment requires precision. If you are not confident in your abilities, it is better to call a specialist.