We rehang the doors on the Atlant refrigerator: instructions with photos and tips

Hanging the doors on a two-chamber refrigerator Atlant is a task that owners face when moving, renovating a kitchen, or simply wanting to optimize space. The procedure seems simple, but has nuances: from the location of the hinges to the type of seal fastening. Errors here are fraught distortion of doors, violation of tightness or even breakage of plastic parts.

This article contains a step-by-step algorithm taking into account the features of the models. Atlant (including series MHM, NRM, HM), a list of necessary tools and critical momentsthat are not written about in standard instructions. For example, why can’t you just “twist the hinges the other way around” or how to avoid damaging the display cable (if there is one).

If your refrigerator was released after 2018, most likely, it universal hinges with the ability to rehang without replacing parts. For models older than 10 years, you may need to purchase a mirror set of hinges - we will also tell you about this.

1. Preparation: tools and conditions

Before you begin, make sure you have everything you need. Minimum set of tools:

• 🔧 Phillips screwdriver (preferably magnetic so as not to lose screws)
• 🔨 5 mm hexagon (for some models Atlant)
• 📏 Tape measure or ruler (to check gaps)
• 🧲 Magnet or tape (to fix the removed door)
• 🧴 Silicone grease (for hinges after hanging)

Important: Atlant uses double-sided hinges on most models, but in series MHM 2808-90 and NRM 6225-100 the lower hinge of the freezer may be asymmetrical. Check this by the part number (usually indicated on the part itself). loop).

⚠️ Attention: If the refrigerator is with electronic display (for example, Atlant XM 6025-031), before removing the door, turn off the power and carefully disconnect the cable cable from the body. Do not bend or pull it - this will lead to broken contacts.

Work on a flat surface. If the refrigerator is on a carpet or uneven floor, place plywood or cardboard under it to avoid distortion when installing the doors. The temperature in the room should not be lower than +18°C - in cold weather the plastic becomes brittle.

Is the refrigerator unplugged?

Have all products and shelves been removed from the doors?

Is there an assistant to hold the door (weight can exceed 10 kg)?

Is a place prepared for storing the removed parts?-->

2. Re-hanging scheme: upper and lower. hinges

On two-chamber models Atlant the algorithm differs from single-chamber ones. There are two doors: refrigeration chamber (upper) and freezer (lower). Their hinges are independent, but connected by a common axis. data-i="99">refrigerator compartment

Procedure:

1. Remove the decorative plugs from the hinges (pry them off with a flat screwdriver).
2. Unscrew the screws of the upper hinge of the refrigerator compartment (usually 3-4 pieces).
3. Hold the door, carefully remove it from the axis and place it on a soft surface (for example, a blanket).
4. Turn the hinge 180° and install it on the opposite side, mirroring the fastening.
5. Repeat the steps for bottom hinge of the freezer.

Critical point: on models with the No Frost system (for example, Atlant MHM. 2835-90) there is a seal heating tube running inside the freezer door. When removing the door, do not pull it sharply - you can damage the tube.

For visualization, here is a table with the location of hinges on popular models:

What to do if the screws are not are they unscrewed?

If the screws are “stuck” or do not give in, do not apply excessive force - this can strip the threads. Treat them with WD-40 or an equivalent, wait 10-15 minutes and try again. For plastic bushings (available in some models), use a hexagon, not a screwdriver, so as not to damage the edges.

3. Rearranging the seal: why is it important

The sealing rubber on the doors Atlant has asymmetric profile. If you simply reposition the door without adjusting the seal, the seal will be broken and the refrigerator will operate with overload. result:

• 🌡️ The temperature in the chambers will increase (up to +8°C instead of +4°C).
• ❄️ Ice will begin to freeze on the back wall (even in models with No Frost).
• 💰 Electricity consumption will increase by 15-20%.

To rearrange the seal correctly:

1. Remove it from the door, starting from the top corner. The rubber is attached to the groove of the plastic panel.
2. Rinse the seal with warm water. with soap and dry.
3. Turn it 180° (if the profile is symmetrical) or replace it with a new one (if asymmetrical).
4. Insert the seal back into the groove, starting from the bottom corner. Use a soap solution to facilitate the process.

⚠️ Attention: On models. with magnetic seal (for example, Atlant XM 4324-100) you cannot use silicone grease - it breaks the adhesion. Instead, apply talc or a special spray for rubber seals.

After installation, check the tightness sheet test: clamp a strip of paper between the door and the body. If the sheet is pulled out without force, the seal is installed incorrectly.

4. Features of models with a display and No Frost

Refrigerators Atlant with electronic control (series XM 6025, MHM 2835) have additional display power cablewhich passes through the hinge When reversing the door you need:

1. Disconnect the refrigerator from the mains and wait 5 minutes (capacitors discharge).
2. Remove the top cover of the case (usually secured with 2-3 screws).
3. Disconnect the cable connector from the control board (it is marked or has a color mark).
4. Carefully pull the cable through the loop to the opposite side.

In models with No Frost (for example, Atlant MXM 2808-90) there is a heating element of the sealinside the freezer door. When reweighing:

• 🔌 Disconnect the heater connector (it is located under the plastic door panel).
• 🔄 Move the heating tube to the other side without bending it.
• 🔧 Make sure that after installation the tube does not touch the moving parts of the loop.

⚠️ Attention: If after rehanging an error code appears on the display E1 or E2, this means the sensor circuit is open. Check the cable connections and contacts on the board. In 80% of cases, the problem is solved by reconnecting the connector.

5. Checking and adjustment after rehanging

After installing the doors, perform 4 mandatory checks:

1. Tightness: close the door and check the cracks with a flashlight. Light should not penetrate inside.
2. Door movement: it should open smoothly, without squeaks. If it’s tight, lubricate the hinges with silicone grease.
3. Level: use a bubble level to make sure the door is not warped. The permissible gap is no more than 2 mm.
4. Electronics: turn on the refrigerator and check the operation of the display, backlight, open door signal.

If the door opens spontaneously, the problem is the skewed loops. Adjust them with a wrench:

• 🔩 Loosen the top hinge screw.
• 📏 Adjust the vertical position of the door.
• 🔧 Tighten the screw and check result.

For models with automatic closing (for example, Atlant XM 6325-100), calibration of the mechanism may be required. To do this:

1. Open the door 90°.
2. Press and hold the button Super Cool 5 seconds.
3. Close the door - the mechanism will calibrate automatically.

6. Common mistakes and how to avoid them

Even if you follow the instructions, you can make mistakes that will lead to breakdown. Here top 5 problems and their solutions:

1. The door does not close tightly

Cause: the seal is installed incorrectly or the hinges are skewed.

Solution: check the symmetry of the seal and adjust the hinges to the level.

2. There is play in the hinges

Cause: the screws are not tightened enough or the threads are broken.

Solution: use washers for a tight fit or replace the hinge.

3. The display does not work after rehanging

Cause: the cable is damaged or the connector is not connected.

Solution: disassemble the top cover and check the contacts.

4. The refrigerator began to operate loudly

Cause: when the door is skewed, the vibrating compressor touches the body.

Solution: level the refrigerator and adjust the legs.

5. Ice freezes on the new side of the seal

Cause: the seal heating has not been repositioned (in models with No Frost).

Solution: dismantle the door and move the heating element.

⚠️ Attention: If after rehanging the refrigerator starts publish creaking when opening the door, do not ignore it. Most likely, the hinges are installed without lubrication or misaligned. Over time, this will lead to wear of the plastic bushings and the need to replace them.

7. When is it better to contact a specialist

Not all cases can be solved on your own. Contact the service center if:

• 🔧 The thread in the hinge or body of the refrigerator is broken.
• 💻 An error appears on the display that cannot be reset (E3, E4, E5).
• ❄️ After rehanging, the refrigerator does not cool or constantly works compressor.
• 🔌 The display cable or heating seal is damaged.

The cost of re-hanging the doors in the service Atlant is from 1500 to 3500 rubles (for 2026), depending on the model and region If the refrigerator. under warranty, the procedure should be free - but only on condition that the overhang is due to manufacturing defects in the hinges.

Independent repair will cost less, but remember: improper installation of hinges or seals can lead to failure of the compressor - and this is a repair from 8000 rubles.

FAQ: Answers to frequently asked questions

Is it possible to rehang only one door (for example, only the freezer)?

Technically yes, but this will upset the balance of the structure. The doors Atlant are balanced in weight, and if you reweigh only one, the second will open with the same weight. force or spontaneously. The exception is models with independent hinges (for example, Atlant XM 4324-100), but in this case it is recommended to re-hang both doors to ensure even wear of the hinges.

Is it necessary to defrost the refrigerator before overweight?

Required! Even if you have a model with No Frost. Turn off the refrigerator 12-24 hours before work so that the ice on the evaporator melts. This will prevent a short circuit when manipulating the electronics and make it easier to remove the doors (ice may have frozen to the seal).

What to do if after re-hanging, did the refrigerator freeze worse?

Most likely, the seal is broken. Check:

1. The tightness of the seal (use a sheet of paper).
2. The integrity of the heating of the seal (in models with No Frost).
3. No door skew (the gaps should be the same around the entire perimeter).

If the problem remains, call a technician to diagnose the compressor.

Where to buy mirror hinges for the old model Atlant?

For refrigerators older than 10 years, original hinges can be found order:

• On the website official service center Atlant (section "Spare parts").
• In stores of spare parts for household appliances (for example, "220 Volt", "Techport").
• On Avito or Yule (check compatibility by catalog number).

The average cost of a set of hinges is 800-1500 rubles.

Is it possible to reverse the doors on a refrigerator Atlant with a French door?

No, this is not possible. Models with French door (for example, Atlant XFM 6025-100) have a fixed the design of the hinges and are not intended for rehanging. An attempt to do this will lead to a breakdown of the door synchronization mechanism.