After delivering a new household appliance to the kitchen, owners often rush to immediately plug it into the network and fill it with food. However, for brand equipment Aceline, as for most modern refrigeration units, it is critical to follow the correct initial start-up algorithm. Ignoring the acclimatization stage can lead to compressor failure or incorrect operation of the system. No Frost.
In this article we will look in detail at how to set up a refrigerator Aceline to ensure maximum energy efficiency and food safety. You will learn about the nuances of setting temperature conditions, activating additional functions and checking the tightness of door seals. Proper setup from the first minutes of operation will extend the service life of the device.
Preparation for first use and acclimatization
The first step after unpacking is a visual inspection and installation of the unit on a flat surface. An unstable housing position is a common cause of increased noise and vibration, which users sometimes mistake for a compressor malfunction. Use a building level to check the horizontal position and adjust the height of the legs using the special key included in the kit.
It is extremely important to wait a certain time before connecting to the power supply, especially if transportation was carried out in winter or at low temperatures. The oil in the compressor could thicken or move into the cooling circuit, and a sudden start will lead to water hammer.
⚠️ Attention: If the refrigerator was brought in from the cold, let it stand in a warm room for at least 4-6 hours before turning it on. This is necessary to evaporate condensation and restore the viscosity of the compressor oil.
After the device has warmed up to room temperature, wipe the internal shelves with a damp cloth using a mild detergent. This will remove factory dust and possible plastic smell, which is typical for new products.
☑️ Initial launch of Aceline
Control interface: mechanics and electronics
The model range Aceline is divided into two main categories according to the type of control: mechanical and electronic. In mechanical models, adjustment is carried out by a rotary regulator located inside the chamber. Typically, the scale has divisions from 1 to 5 or from Min to Max, where number 1 corresponds to the least intense cooling, and 5 to the maximum.
Electronic models are equipped with a display on the door or a hidden control panel. Here the adjustment is made with an accuracy of a degree. To change parameters, you must press the Temp or Modebutton, after which the flashing value indicates the active adjustment zone. Using the + and - buttons allows you to set the exact value, for example +4°C for the main chamber.
It is important to understand the difference between the air temperature in the chamber and the degree of cooling of the products. Sensors in the electronics react to changes in air temperature, so frequent opening of the door can cause false signals to the compressor.
Difference between Eco mode and Max Cooling
Eco mode optimizes the operation of the compressor for minimal energy consumption, maintaining the temperature within a narrow range. The Max Cooling mode forces the compressor to work continuously until the minimum possible temperature is reached, which is useful when loading a large volume of fresh products, but increases energy consumption.
Optimal temperature conditions for storage
Correct temperature settings are the key to freshness of products and the absence of ice. For the main chamber of refrigerators Aceline the gold standard is considered to be the range from +3°C to +5°C. It is with these parameters that the growth of bacteria slows down, but the food does not freeze.
In the freezer, regardless of the defrosting system, the temperature must be maintained -18°C or lower. This value guarantees long-term storage of meat, fish and vegetables without losing their nutritional properties. If you set the mode -24°Cuse it only for quick freezing, after which be sure to return the standard values.
- 🥩 Raw meat and fish: store on the bottom shelf or in the freshness zone at a temperature of 0 to +2°C.
- 🥛 Dairy products: optimally placed on middle shelves, where the temperature is stable and is +4°C.
- 🥬 Vegetables and fruits: require high humidity and a temperature of about +6°C, so the drawers below are the best place.
Do not forget that the location of products affects circulation air. Filling the chamber by more than 70% makes it difficult for the system to operate No Frost and leads to uneven cooling.
Setting up the No Frost system and water drainage
Most modern models Aceline equipped with a system No Frostthat prevents the formation ice. The principle of its operation is based on forced circulation of cold air. For correct operation, it is important to ensure free air flow between the back wall and the products.
Condensation may accumulate in the drainage system, which is discharged through a special hole. If you notice water on the floor or inside the chamber, check to see if the drainage hole is clogged with crumbs or ice. Cleaning should be done with a soft tube or brush, avoiding the use of sharp objects.
⚠️ Attention: Never pick the drainage hole with a knife or wire. You can damage the evaporator or puncture the cooling circuit, which will lead to a freon leak and expensive repairs.
Periodically, about once every six months, it is recommended to carry out preventive defrosting even for systems No Frost, turning off the device for 12-24 hours. This will allow moisture to evaporate in hard-to-reach places and refresh the internal channels.
Table of recommended settings for different products
For the convenience of users, we have compiled a summary table that will help you quickly navigate the refrigerator settings Aceline depending on the type of loaded products. Following these recommendations will help avoid food spoilage.
| Product type | Recommended zone | Temperature (°C) | Shelf life (approximate) |
|---|---|---|---|
| Fresh meat | Bottom shelf / 0°C zone | 0...+2 | 2-3 days |
| Dairy products | Middle shelves | +3...+5 | 5-7 days |
| Eggs | Door shelf | +5...+8 | 15-20 days |
| Frozen berries | Freezer | -18...-24 | up to 12 months |
Please note that the door shelves are the warmest place in the refrigerator due to contact with the warm air of the room when opened. Therefore, do not store perishable foods such as milk or open deli meats there.
Quick freezing and energy saving modes
Function Super Freeze (Super Freeze) is useful when you bring home a large amount of fresh food. When this mode is activated, the refrigerator operates at maximum power, quickly freezing the contents and preventing the formation of large ice crystals that destroy the structure of food cells.
Models with electronic control often have a mode Eco or Energy Saving. Its activation increases the temperature in the chambers to the upper limits of normal (for example, +6°C in the refrigerator), which significantly reduces energy consumption. This mode is ideal when the refrigerator is not completely full or food with a long shelf life is stored in it.
It is not recommended to keep the super freeze mode on all the time. This puts excess stress on the compressor and can cause it to overheat. Use a timer or do not forget to turn off the function manually after freezing.
Diagnostics and troubleshooting
During operation, users may encounter situations that seem to be malfunctions, but are not. For example, heating the side walls of the case is a normal process of heat removal by the condenser, which is built into the sides of modern refrigerators. Aceline.
If you hear gurgling or gurgling, this is refrigerant moving through the system. These sounds are especially noticeable immediately after the compressor stops. It is also possible for plastic to crack when the temperature changes, which is a consequence of thermal expansion of materials.
⚠️ Attention: If the refrigerator makes a loud knock, the humming gets stronger over time, or the appliance does not cool, but the compressor runs continuously - these are signs of failure. In such cases, independent repairs are prohibited; you must contact a service center.
A frequent problem is a loose door fit. Check to see if there is anything obstructing the seal and make sure the refrigerator is vertical. To check the tightness, you can clamp a sheet of paper with the door: if it falls out with a slight tug, the hinges need to be adjusted.
Frequently asked questions (FAQ)
How long should the Aceline refrigerator run before loading food?
After the first turn on, let the refrigerator run idle for 2-3 hours. During this time, it will reach the required temperature, and the thermostat will turn off the compressor. Only after this can you load products so as not to create excess load on the system.
Why does ice form on the back wall of the refrigerator compartment?
In models with a drip defrosting system (crying wall), the formation of a small amount of ice or frost on the back wall is a normal operating process. Periodically, the compressor turns off, the wall heats up, and the ice melts, flowing into the drain. If the layer of ice is too thick, check the tightness of the door.
Is it possible to install the Aceline refrigerator close to the wall?
No, for effective heat exchange you need a gap between the back wall of the refrigerator and the wall of the room of at least 5-10 cm. It is also advisable to leave space on the sides, if conditions allow, so that the condenser does not overheated.
What to do if the refrigerator makes a lot of noise after installation?
Check that all shipping bolts and films have been removed. Make sure the refrigerator is level and does not wobble. If the feet are not adjusted, vibration is transmitted to the floor and increases the noise. Also check whether the refrigerator pipes are touching the wall or furniture.