Adjusting the temperature in the Beko refrigerator using a knob: instructions for all models

Mechanical thermostats in refrigerators Beko remain popular despite the spread of electronic panels. Their main advantage is simplicity and reliability: there is no risk of firmware failure, and setup takes only a few seconds. However, many users encounter difficulties during the first adjustment: they do not understand which way to turn, how to correlate the scale divisions with real degrees, and why after the changes the temperature does not meet expectations.

In this article we will look step-by-step instructions on adjusting the temperature with a twist for all series of refrigerators Beko (including CSA, CSK, GNE etc.), we will explain the principles of operation of a mechanical thermostat and give practical advice on optimizing modes. We will pay special attention to typical mistakes that lead to icing of the chambers or spoilage of food.

If your refrigerator is equipped with electronic control panel, these instructions are not suitable - refer to the manual for the specific model. Mechanical controls are easy to identify: this is a round knob (usually located inside the refrigerator compartment on the right wall or on top) with numbers from 1 to 5 (less often up to 7) or marks Min/Max.

1. Where is the temperature regulator located in Beko refrigerators

In most models Beko a mechanical thermostat is located inside the refrigerator compartment - this is a standard solution for the brand. The exact location depends on the series:

• 🔹 Classic models (series CSA, CSK): the regulator is located on the right side wall, closer to the upper corner. The handle can be plastic or metal, with printed numbers.
• 🔹 Two-chamber refrigerators (series GNE, RCSK): often two separate regulators - one for the refrigerator compartment (inside it), the other for the freezer (on a panel outside or inside the freezer).
• 🔹 Models with a bottom freezer (series CN, DS): the regulator is usually hidden under the shelf or behind a plastic plug on the top panel of the refrigerator.

If you can’t find the handle, check:

1. Light the back wall of the chamber with a flashlight - sometimes the regulator is located inconveniently and is hard to see.
2. Look under the plastic covers - in some models the handle is hidden behind a decorative panel.
3. Pay attention to freezer compartment: in two-compressor refrigerators there may There should be a separate regulator.

Important! In refrigerators Beko with a system No Frost the temperature regulator can be combined with a cooling mode switch (for example, Super Cool or Holiday). In this case, the knob has additional marks.

2. How to turn the regulator correctly: clockwise or counterclockwise

This is the most common question from users. In refrigerators Beko the standard rule applies:

• 🔄 Clockwise (to the right) - increase in cold (numbers increase, temperature decreases).
• 🔄 Counterclockwise (left) - decrease in cold (numbers decrease, temperature rises).

However, there is a nuance here: the scale on the regulator may be reversed! To avoid mistakes, pay attention to the labels:

• 🔢 If next to the numbers there are inscriptions Min (left) and Max (right) - the rule is standard.
• 🔢 If the numbers increase from left to right (for example, ... current position of the regulator: 1 - minimal cold, 5 — maximum.
• 🔢 In rare models (for example, Beko TSE 1242) the scale is inverted - check the instructions.

To check the current position of the regulator:

1. Look at which division the mark indicates (usually it is a mark or an arrow on the handle).
2. If there is no mark, carefully turn the knob 1 click clockwise, then return it back - this way you will determine the current position.

How to understand that the regulator Is it broken?

If you don’t hear clicks when you turn the knob, it scrolls without resistance, or the temperature does not change for 6–8 hours, the thermostat is faulty. Replacement is required (the part costs 800–1500 ₽ depending on the model).

3. Optimal temperature settings for the refrigerator and freezer compartments

The manufacturer Beko recommends the following modes for most models:

Important take into account:

• 🌡️ In summer or in hot climates, set the regulator 1 notch higher (for example, instead of 3 - position 4).
• ❄️ In winter (at room temperature below +16°C) reduce the setting by 1 notch to avoid icing.
• 🍗 When loading a large number of products (for example, after shopping), temporarily increase the cold for 6-12 hours.

Warning: if the temperature in the freezer is above −12°C, the products will spoil faster, and the compressor will work in increased mode, which reduces its life.

4. How to check that the temperature corresponds to the settings

The mechanical thermostat does not show exact degrees, so use household thermometer to control (costs 100–300 ₽). Test algorithm:

1. Place the thermometer in the center of the refrigerator compartment (on the middle shelf).
2. Close the door and do not open it for 8-12 hours.
3. Compare the readings with the table above. If the difference is more than 2°C, adjust the knob.

Typical symptoms incorrect setting:

• 🚨 Snow “coat” on the back wall —temperature too low (controller in position 4–5).
• 🚨 Condensation on food or walls —temperature above +6°C (controller in position 1 or broken).
• 🚨 The compressor runs without stopping —a freon leak or a thermostat malfunction is possible.

For the freezer:

• 🧊 If the ice melts when the door is opened, the temperature is above −15°C.
• ❄️ If the products are covered with a thick layer of frost, the temperature is below −20°C (excessive setting).

Tip: in refrigerators Beko with a system No Frost check the temperature not only with a thermometer, but also by the condition of the products. For example, ice cream should be hard, but not “rocky,” and milk should be slightly chilled, but not frozen.

5. Common mistakes when setting the temperature with a twist

Even experienced users sometimes make mistakes that lead to food damage or breakdowns. Let's look at the most common ones:

• ⚠️ A sharp change in the position of the regulator. If you turn the knob from 2 to 5 at once, the compressor will work for wear. Correct: change the setting gradually (1 division per day).
• ⚠️ Ignoring the external temperature. In hot weather, the refrigerator needs to be “strengthened”, and in winter – weakened. Many people forget to adjust the settings according to the seasons.
• ⚠️ Adjustment “by eye” without a thermometer. It is impossible to visually determine +4°C or +6°C - use a measuring device.
• ⚠️ Closing the regulator with products. If the handle is blocked by cans or bags, it can be accidentally knocked over. Keep the regulator area free.

A separate problem - mismatch between the settings of the freezer and refrigerator compartments. For example, if the freezer is −24°C, and the refrigerator is +8°C, this is a sign of:

• Faults thermostat (replacement required).
• Leaks freon (needs repair).
• Clogs capillary tube (master diagnostics).

⚠️ Attention! If, after changing the settings, the temperature does not stabilize within 24 hours, and the compressor runs without pause for more than 30 minutes, immediately unplug the refrigerator and call a technician. This may be a sign of a critical breakdown, which will lead to failure of the motor-compressor (replacement cost - from 5,000 ₽).

6. How to save energy without damaging food

The refrigerator Beko consumes up to 30% of all electricity in the house. Correct temperature settings will help optimize costs:

• 💡 Set the regulator to 2–3 (this corresponds to +4°C in the refrigerator compartment and −18°C in the freezer).
• 💡 Use the mode Holiday (if available) during a long absence - it maintains +10°C, saving up to 40% energy.
• 💡 Defrost the refrigerator if the ice thickness is more than 5 mm - ice worsens heat transfer and makes the compressor work longer.
• 💡 Do not place the refrigerator next to the stove or radiator - this will force it to “catch up” the cold in an enhanced mode.

Additional tips:

• 🔌 Turn off the function Super Freeze 24 hours after loading food - it increases energy consumption by 20-30%.
• 📦 Do not load the chambers by more than 70% - air circulation is disrupted and the refrigerator spends more energy on cooling.
• 🚪 Check the rubber seals: if they are worn out, the cold “leaks away” and the compressor turns on more often.

⚠️ Attention! If your refrigerator Beko manufactured before 2015, it may use an outdated refrigerant R-134awhich is less efficient at high loads. In this case, energy savings are achieved only through optimal temperature settings - modern “eco” modes for such models are irrelevant.

7. What to do if the temperature does not change after adjustment

If you turn the knob, but the temperature in the chambers remains the same, the reasons may be the following:

• 🔧 Thermostat jammed. Try gently moving the handle left and right. If it does not click, the thermostat is broken.
• ❄️ Icing the evaporator. Defrost the refrigerator for 12–24 hours, then repeat the setting.
• 🔌 Problems with the compressor. If the motor does not turn on or runs without stopping, diagnostics are required.
• 📡 Temperature sensor malfunction (in models with electronic control, but a mechanical handle).

For diagnostics:

1. Unplug the refrigerator for 10 minutes, then turn it on again. Sometimes this resets frozen settings.
2. Listen to the compressor: if it does not start or makes unusual sounds (knocking, humming), call a technician.
3. Check whether the light inside the chamber is on - if not, the problem may be electrical.

If the refrigerator Beko under warranty, do not try to repair it yourself! Contact the service center - user intervention will void the warranty.

FAQ: Frequently asked questions about setting the temperature in Beko refrigerators

❓ How can you tell if a Beko refrigerator is freezing too much?

Signs of excessive cooling:

• Products in the refrigerator compartment freezes (for example, milk turns into ice).
• A thick snow “coat” (more than 5 mm) forms on the back wall.
• The compressor operates almost without pauses (norm: 10–15 minutes of operation, 20–30 minutes of rest).

Solution: turn knob 1 notch counterclockwise and check the temperature after 6-8 hours.

❓ Is it possible to set different temperatures in the refrigerator and freezer compartments?

In most models Beko s with one compressor The temperature setting is interconnected: changing the regulator affects both chambers. However:

• In two-compressor refrigerators (series BCS, GNE) the chambers are independently regulated.
• In models with electronic control (even with a mechanical handle), you can set different modes through the panel.

Check the type of your model in the instructions or on the sticker inside the camera (look for the inscriptions Twin Cooling or Dual System).

❓ Why, after adjustment, does the temperature fluctuate: sometimes -20°C, sometimes -10°C?

This is a sign thermostat malfunction or freon leaks. data-i="258">thermostat malfunction

• Clogged capillary tube (needs cleaning).
• Loose door fit (check the seal).
• Failure in fan operation (in models with No Frost).

Actions: defrost the refrigerator for 24 hours. If the problem persists, call a technician.

❓ What temperature should be in the freshness zone?

Freshness zone (if yours has one) model) works optimally at 0°C...+1°C. To do this:

• Set the main control to position 2–3.
• If the zone has a separate knob, set it to Medium or middle position.
• Do not load the zone more than 2/3 - this disrupts air circulation.

Ideal for storing greens, berries, cheeses and sausages without packaging.

❓ Do you need to change the temperature settings in winter and summer?

Yes, this is required! Recommendations:

• 🌞 Summer (room temperature above +25°C): increase the setting by 1 division (for example, from 3 to 4).
• ❄️ Winter (temperature below +16°C): decrease by 1 division (from 3 to 2).
• 🏡 Temperature difference (for example, during ventilation): temporarily set the regulator to maximum, then return to normal.

Ignoring seasonal adjustments leads to increased wear on the compressor or icing.