After purchasing or transporting household appliances, it is important to correctly perform the initial start-up in order to extend the life of the compressor. Candy refrigerator requires an adaptation period after transportation, especially if it was in horizontal position. The oil must drain back into the crankcase, and the refrigerant must be distributed throughout the system, which takes from two to four hours.
The first start-up is carried out in an empty state, without loading food, so that the unit quickly reaches the set temperature. At this time, it is not recommended to open the doors frequently, since thermostat it should fix a stable cooling cycle. Modern models are equipped with electronic control, which automatically optimizes operation at startup.
Particular attention should be paid to the horizontal position of the body: if the legs are installed unevenly, problems may arise with a tight fit of the doors. This will lead to the formation of ice and increased load on the engine. Correctly setting the tilt angle ensures automatic closing of the doors when the deviation from the vertical is up to 3 degrees.
⚠️ Attention: If the refrigerator has just been brought from the store in winter, let it warm up to room temperature before plugging it in to avoid damage to the contacts and condensation. on the board.
Basic setting of temperature and operating modes
The main task of the user is to set the optimal temperature mode corresponding to the current load and season. In classic models with mechanical control, this is controlled by a rotary thermostat knob inside the chamber. The numbers on the regulator do not indicate degrees, but cooling intensity: the higher the value, the colder it will be inside.
Electronic models, such as the series Candy Smart, allow you to set exact values in degrees Celsius through the control panel on the door. The standard recommendation is to set it to +4°C for the refrigerator compartment and -18°C for the freezer compartment. These settings provide better food safety and energy efficiency.
If you notice that the food in the back of the chamber is freezing, and the temperature at the door is higher than normal, you need to adjust the settings. It is also worth considering the amount of stored supplies: a fully loaded refrigerator operates more stable, but requires more powerful initial cooling.
- ❄️ For daily storage, the "Eco" mode or medium thermostat settings are recommended.
- 🚀 The "Super Cool" function activates maximum power for several hours.
- 🧊 The "Super Freeze" mode is necessary for quickly freezing fresh food in the freezer.
- 💡 The "Alarm" indicator signals a violation of the temperature regime or an open door.
Managing the electronic display and functions
It is important for owners of models with a display to understand menu navigation in order to activate additional functions. The control panel is usually touch responsive but may be child locked. Unlocking often requires a long press of a button with a picture of a lock or a combination of keys, which is indicated by a sound signal.
Function "Vacation" (Holiday mode) puts the refrigerator compartment into an economical mode with a temperature of about +15°C, preventing the appearance of mold and odor while the freezer continues to operate normally. This is an ideal solution for long-term absence of owners.
Some advanced models support control via Wi-Fi and application Candy Simply-Fi. This allows you to remotely change settings, diagnose faults and receive notifications. To activate, you need to connect to your home network, following the instructions on the screen.
| Function | Designation | Description of action |
|---|---|---|
| Super Cool | Snowflake / Drop | Intensive cooling of the refrigerator cameras |
| Super Freeze | Snowflakes (a lot) | Maximum freezing in the freezer compartment |
| Holiday | Palm / Suitcase | Economy mode for the upper chamber |
| Lock | Lock | Blocking buttons from accidental pressing |
☑️ Checking display settings
Adjusting the shelves and ventilation system
The correct placement of products directly affects the circulation of cold air. In models with the system No Frost or Low Frost it is important not to block the ventilation holes on the rear wall. The air should freely wash all products, ensuring a uniform temperature.
Glass shelves in Candy refrigerators are often height-adjustable. To change the level, the shelf must be slightly lifted at the front edge and pulled out of the guides, then set to the desired height. Some models allow shelves to be folded in half to accommodate tall bottles.
Zoning the space helps maintain freshness longer. It is best to store meat and fish on the bottom shelf, where it is coldest, and dairy products and ready-made meals on the middle levels. Door baskets are designed for foods that do not require extreme cooling, such as sauces or drinks.
⚠️ Warning: Never place hot or warm food inside a running refrigerator. This upsets the temperature balance and causes the compressor to wear out, which can lead to breakdown.
How to defrost freshness zones correctly?
In some Candy models, the freshness zone (zero chamber) requires special attention. If you notice ice in this compartment, check that the drawer is tightly closed. Sometimes it is necessary to manually remove ice if the moisture drainage system is clogged with crumbs. Use a soft cloth and warm water, avoiding sharp objects.
Diagnostics and error reset (Fault codes)
Modern Candy equipment is equipped with a self-diagnosis system that displays error codes on the display when problems are detected. Most often, users encounter alarms about temperature increases or sensor malfunctions. Understanding the codes helps you quickly take action.
The most common errors are related to the evaporator temperature sensor or a broken door seal. If the corresponding symbol flashes on the screen, check the tightness of the seal and the absence of foreign objects that interfere with closing.
To reset the error, it is often enough to eliminate the cause of its occurrence and press the reset button or turn off the refrigerator from the network for 10-15 minutes. However, if the error repeats, this indicates a technical malfunction that requires the intervention of a technician.
- 🔴 E1 - Malfunction of the temperature sensor in the refrigerator compartment.
- 🔵 E2 - Problem with the sensor in the freezer compartment.
- 🟡 E3 - Defrost or evaporator sensor error.
- 🟠 F - Signal about defrosting or increasing temperature (F1, F2, etc.).
Seasonal adjustments and energy saving
Depending on the time of year, adjustments to the settings may be required. In summer, when the ambient temperature is high, it is more difficult for the refrigerator to release heat, so you should not place it close to the wall or heating devices. In winter, the situation is the opposite, but modern models operate in a wide climatic range.
The climate class indicated in the passport (SN, N, ST, T) determines the permissible ambient temperature. Operation outside of these standards, for example, in an unheated country house in winter, can lead to the oil in the compressor solidifying and breaking during startup.
To save energy, it is recommended to regularly check the condition of the sealing rubber bands. If they are dirty or damaged, the cold goes away and the compressor turns on more often. Wipe the seal with a soft sponge and soapy water once a month.
⚠️ Attention: Specifications and control interfaces may vary depending on the specific model and year of manufacture. Always check the official user manual that came with your device, especially when connecting to a smart home.
Why does the refrigerator hum after setting the silence?
Some models have a “Night” or “Silent” mode, which turns off the fan or reduces the speed of the compressor. However, the equipment cannot be completely silent - the flow of refrigerant through the tubes can be heard. If the noise has become loud and metallic, this is a reason for diagnosis.
Frequently asked questions (FAQ)
How to unlock the control panel if it has locked itself?
Usually, to unlock you need to find the button with the image of a lock and hold it for 3-5 seconds until a beep sounds. Some models require simultaneous pressing of two buttons, for example, "Temperature" and "Mode". For the exact combination, see the instructions for your model Candy.
What to do if after setting the temperature does not change?
If you change the settings, but the temperature inside does not stabilize within 24 hours, check that the doors are tightly closed and there are no drafts. Also make sure that the refrigerator is not overloaded with foods that block air flow. If the problem persists, the thermostat or sensor may fail.
Is it possible to transport a configured refrigerator lying down?
Transporting it lying down is possible, but not advisable. After transporting it in a horizontal position, you must let the refrigerator stand upright for at least 4-6 hours (preferably a day) before turning it on. This is necessary so that the compressor oil flows back into the crankcase and does not enter the cooling circuit.
How to activate the super freeze mode on the display?
Press the "Super Freeze" button (often indicated by snowflakes). The indicator will light up and the freezer will enter maximum power mode. In most models, this mode turns off automatically after a certain time or when the chamber is full, but it is better to turn it off manually when the food freezes.