After purchasing and delivering large household appliances to the kitchen owners are often faced with the need for proper initial setup. Two-chamber models Candy require special attention to temperature conditions, since the safety of products and the durability of the compressor depend on this. An incorrect starting configuration can lead to the formation of ice or, conversely, insufficient cooling of the chamber.
Modern units of the Italian brand are equipped with electronic control, which allows flexible adjustment of operating parameters. However, for the system to work correctly, it is necessary to strictly follow the initial startup algorithm. In this article we will analyze all the nuances of setting, from choosing the installation location to fine-tuning the thermostats.
Before you start setting the modes, make sure that the device has stood in an upright position for at least 4 hours after transportation. This time is necessary for the oil to spread throughout the cooling system and stabilize the refrigerant pressure. Ignoring this stage can lead to failure compressor in the first weeks of operation.
Initial installation and preparation for launch
The first step is to correctly place the unit in the room. For efficient operation of the heat exchanger, free air circulation around the housing is required. The gaps between the walls of the device and the furniture should be at least 5-7 centimeters. If you neglect this rule, the motor will work with increased load, trying to compensate for overheating.
After installation, it is necessary to align the device horizontally. Adjustable legs allow you to compensate for uneven floors, which is critical for the normal operation of the doors and condensate drainage system. Tilt back will ensure automatic closing of the doors if they are released at a slight angle.
⚠️ Attention: Do not connect the device to the power supply immediately after skidding out of the cold. A sudden change in temperature inside the electronics can cause condensation to form on the control boards, which will lead to a short circuit.
It is also important to check the integrity of the door seals. They should fit snugly around the entire perimeter of the body. Any gaps will lead to constant penetration of warm air, and the system will operate continuously without achieving the set parameters.
☑️ Initial preparation of the refrigerator
Adjusting the temperature mode
The central element of the setting is the installation optimal temperature. In two-chamber models Candy the system No Frost or static cooling is often used, which dictates its own requirements for settings. For the main camera, the optimal range is considered to be from +3 to +5 degrees Celsius.
Control can be carried out by a mechanical regulator or an electronic panel. On mechanical models, turning the knob to the right usually increases the cooling intensity. However, you should not immediately set the maximum value, as this can lead to freezing of food in the freshness zone.
- 🌡️ For the main compartment, set the average value corresponding to 4 degrees.
- ❄️ For the freezer, the optimal temperature is -18 degrees.
- 🍖 When loading a large volume of products, temporarily turn on the super-freeze mode.
- ⏳ Give the device 24 hours to enter operating mode before loading it completely.
Electronic panels allow you to set precise values in steps of one degree. This is especially convenient when storing specific products that require special conditions. For example, to store fresh meat, you can lower the temperature to +1 degree.
Setting up the freezer compartment
The freezer compartment requires special attention, especially if you plan to freeze large volumes of food. The standard temperature of -18 degrees ensures storage of products for up to 12 months without loss of their properties. Lower values have no practical meaning and only increase energy consumption.
The function Super Freeze (super freezing) is designed for quick freezing of fresh food. When this mode is activated, the compressor runs continuously, ignoring the thermostat readings. It should be used only when loading the camera, and after 24 hours, be sure to turn it off manually or wait for automatic shutdown.
| Operating mode | Temperature | Purpose | Duration |
|---|---|---|---|
| Standard | -18°C | Long-term storage | Permanent |
| Super freezing | -24°C | Fresh food freezing | Up to 24 hours |
| Eco mode | -15°C | Short-term storage | As needed |
| Vacation | +10°C (cold.) | Energy saving | Long absence |
Do not forget that densely packing the freezer with a snow coat (in models without No Frost) significantly worsens heat transfer. Regular defrosting will help maintain the temperature values stated by the manufacturer.
Use of special functions and modes
Modern refrigerators Candy are equipped with additional options that expand their functionality. Mode "Vacation" (Eco/Vacation) switches the main chamber into an energy-saving mode with a temperature of about +15 degrees, preventing the formation of mold and odor, while the freezer continues to operate as normal.
Quick cooling function (Fast Cool) is useful when you need to quickly cool food or drinks just brought from the store. The system operates at maximum power for a short period of time, after which it automatically returns to standard settings.
What is the Zero Zone freshness zone?
This is a special compartment in the refrigerator where the temperature is maintained at about 0 degrees and a certain humidity. In such conditions, meat, fish and dairy products remain fresh 2-3 times longer than in a conventional compartment. However, not all Candy models are equipped with a full-fledged zero zone; often it is just a zone of low temperatures.
Some models support control via Wi-Fi and an application hOn. This allows you to change settings remotely, receive notifications about an open door or faults. To activate, you must press and hold the connect button on the control panel.
⚠️ Attention: When using the Vacation mode, make sure that there are no perishable products left in the main compartment. A temperature of +15°C is not sufficient for their safe storage.
Setting up sound signals and indications
Sound notification is an important element of safety and control. The door open alarm starts working if the door is left open for more than 1-2 minutes. This helps prevent the chamber from defrosting and the compressor from overheating.
On many models, you can turn off the sound signal, but leave a visual indication (flashing indicator). This is convenient at night or if there are small children in the house who may be frightened by a sharp sound. To do this, you usually need to hold down the corresponding button on the control panel for 3-5 seconds.
- 🔔 The sound signal duplicates the flashing of the temperature indicator.
- 🔇 Turning off the sound does not eliminate the cause of the alarm (for example, an open door).
- 💡 The temperature increase indicator lights up when the threshold is exceeded at -12°C in the freezer.
If the emergency temperature indicator flashes after the doors are closed for a long time, this may indicate a sensor malfunction or a freon leak. In this case, simple reconfiguration will not help; diagnostics will be required.
Error diagnostics and fault codes
The refrigerator electronics constantly monitor the state of the system. If anomalies are detected, error codes or flashing symbols may appear on the display. For example, a flashing temperature light often indicates that the inside of the chamber is warmer than the set point.
Common error codes may indicate problems with the evaporator or chamber temperature sensors. Replacing the sensors yourself requires disassembling the internal panel and having a multimeter to check the resistance.
Typical Candy indication codes:E1 - Malfunction of the refrigerator compartment sensor
E2 - Malfunction of the freezer compartment sensor
E3 - Problem with the defrost sensor
F - Control board error
If an error code appears, try rebooting the device: disconnect it from the network for 10-15 minutes. If after switching on the error persists, you must contact the service center. Ignoring signals can lead to food damage.
Frequently asked questions (FAQ)
Why does the Candy refrigerator hum loudly after configuration?
Humming may be caused by incorrect installation. Check that the unit is level and that the vibration tubes are not touching the housing or walls. Also, the new compressor may be noisier during the break-in period (up to 2 weeks).
How often do you need to defrost a two-chamber refrigerator?
Models with the system No Frost do not require manual defrosting, it is enough to wash them 1-2 times a year. Static models (with a “crying” wall) need to be defrosted when a layer of ice more than 5 mm thick has formed, usually once every 4-6 months.
Is it possible to change the temperature in the freezer in the summer?
In the summer, with a high ambient temperature in the room, the load on the refrigerator increases. It is not recommended to set the temperature below -18 degrees, as this will cause the compressor to work without stopping. It is better to ensure good ventilation around the device.
What to do if after setting the network indicator does not light up?
Check that the plug is connected to the socket and that there is voltage in the network. If the socket is working, but the indicator does not light up, the indicator light may have burned out or there has been a power surge that has damaged the board. A call to the technician is required.
Are the settings lost when the light is turned off?
In modern models Candy the settings memory is retained. Once the power supply is restored, the device will return to the previously set parameters. However, the super-freezing or fast cooling mode may be reset.