How to set up a Polaris refrigerator: a complete guide with photos and tips

Refrigerators Polaris are popular due to the combination of affordable prices, modern technologies and adaptability to Russian operating conditions. However, even the most advanced equipment requires correct initial setup - not only the service life of the unit, but also the safety of products, the level of energy consumption and comfort of use depend on this. In this article, we will analyze all stages of setup: from basic temperature adjustment to activating special modes, which often go unnoticed by users.

A feature of refrigerators Polaris is a flexible control system, which may differ depending on the series (NoFrost, Direct Cool, Side-by-Side) and year of manufacture. For example, 2023-2026 models feature touchpads with intuitive interfaces, while earlier versions (pre-2022) may have mechanical dials or keypads. We will take these nuances into account and give universal recommendations applicable to most brand lines.

Important: if your refrigerator Polaris was released before 2020, some functions (for example, Vacation mode or Super freeze) may be missing or work differently. In this case, check the instructions for the specific model - it can be found on the official website by serial number (located on the sticker inside the chamber or on the back of the case).

1. Preparing the refrigerator for the first setting

Before you begin adjusting the temperature and modes, the refrigerator Polaris must be properly installed and connected. This affects the accuracy of the sensors and the uniformity of cooling.

Step 1: Level installation. Use a building level to level the refrigerator horizontally. The permissible slope is no more than 1–2°. Adjustment is carried out by rotating the front legs (in models with a rear wall on legs - all four). Uneven installation leads to a loose fit of the door, which increases the load on the compressor by 15-20%.

Step 2: Connect to the network. Refrigerators Polaris sensitive to voltage changes. If your network has frequent surges, use a stabilizer (recommended voltage: 220V ±10%). Do not connect the unit via an extension cord - this may cause overheating of the cable.

• 🔌 Socket must be grounded and located in an accessible place (not behind the refrigerator).
• ❄️ First start: after connecting, let the refrigerator stand 2-3 hours without load (this is necessary to stabilize the refrigerant pressure).
• 🧊 Loading products: start only after reaching the operating temperature (signal on the display or sound signal in some models).

⚠️ Attention: If the refrigerator Polaris was transported in a horizontal position (lying down), wait 6–8 hours before turning it on. This will prevent oil from the compressor from entering the cooling system.

2. Basic temperature setting: optimal values

Temperature is a key parameter that affects food safety and energy efficiency. In refrigerators Polaris adjustment is carried out separately for refrigerator and freezer chambers. Recommended values:

In models with electronic control (for example, Polaris RSM 206 or Polaris P 140), the temperature is set by pressing the buttons FRIDGE (refrigerator compartment) and FREEZER (freezer). In mechanical refrigerators (series Polaris C) a regulator with divisions from 1 to 7 is used, where:

• 🔢 1–2 — minimum cooling (suitable for winter period or low load).
• 🔢 3–4 — optimal mode for most conditions.
• 🔢 5–7 —maximum cooling (used at high room temperatures or full load).

How to check the accuracy of the settings? Place the thermometer in a glass of water (for the refrigerator) or between foods (for the freezer) for 12 hours. If the readings differ from the set values by more than 2°C, calibration or checking the door seal is required.

3. Special modes: when and how to use them

Modern refrigerators Polaris are equipped with additional functions that simplify operation in different situations. Let's look at the most useful of them:

• ❄️ Super Freeze (Super Freeze): activated 12–24 hours before loading a large amount of products (for example, before storing berries for the winter). In this mode, the temperature in the freezer drops to −24°C for 6–12 hours, and then automatically returns to normal values. Important: do not leave the mode on for more than a day - this increases the load on the compressor.
• 🍎 Vacation mode (Holiday): maintains the minimum temperature (+10°...+12°C) during prolonged absence. Saves up to 30% of electricity. Turned on by holding the button Holiday (or combination Mode + Freezer in some models). data-i="130">Vacation mode (
• 🔄 Quick cooling (Fast Cool): speeds up the cooling of fresh food (such as warm soups or drinks). Works for 2-3 hours, then turns off automatically.

On models with NoFrost (for example, Polaris PNF 225) there is also a function "Auto defrost", which turns on once every 10-12 hours for 15-20 minutes. It prevents the formation of ice without manual intervention. If frost still appears on the back wall of the refrigerator, check:

1. The tightness of the door (deformation of the seal is possible).
2. The room temperature (at +30°C and above the system NoFrost may not cope).
3. Loading the chamber (too dense placement of products interferes with air circulation).

⚠️ Attention: The mode Super Freeze cannot be activated simultaneously with Fast Cool —this can lead to the compressor protection being activated and the refrigerator temporarily stopping.

Make sure the door is tightly closed

Check the chamber loading (no more than 70% of the volume)

Disable other energy-intensive modes

Check the instructions for maximum operating time-->

4. Setting up the display and sound signals

Electronic control panels in refrigerators Polaris (series RSM, PNF, PS) allow you not only to regulate the temperature, but also to configure the display of information and alerts. Here are the key parameters:

• 🔊 Sound signals: By default, alerts for prolonged door opening (more than 1 minute) and temperature rise are enabled. To turn them off, hold down the Alarm (or Sound) button for 3-5 seconds. In models without a separate button, press Mode + Temp.
• 📊 Display backlight: the brightness is adjusted in the menu Settings → Display. In night mode (Night Mode), the backlight goes off after 10 seconds of inactivity.
• 🔋 Energy consumption indicator: shows the current level of power consumption (low/medium/high). If the indicator lights up red, check:

- room temperature (optimally +16°...+25°C);
- chamber loading (overload increases consumption by 25–40%);
- status door seal.

In refrigerators with Wi-Fi module (for example, Polaris Smart RSM 220W) you can configure notifications via a mobile application. To connect the refrigerator to the network:

1. Activate the pairing mode by holding the button Wi-Fi (5 seconds).
2. In the mobile application Polaris Smart select "Add device."
3. Enter the password for your Wi-Fi network (2.4 GHz networks only).

⚠️ Attention: If after setup the display shows an error E1 or E2, this indicates a problem with the temperature sensor. Try turning off the refrigerator for 10 minutes, then turning it on again. If the error repeats, service is required.

5. Adjusting shelves and organizing space

Proper placement of products affects air circulation and uniform cooling. In refrigerators Polaris shelves and containers are usually height-adjustable, and in models Side-by-Side (for example, Polaris SBS 230) there are additional compartments for bottles and large packages.

Loading recommendations:

• 🥦 Upper shelves: products that do not require strong refrigeration (sauces, cheeses, eggs). The temperature here is 1–2°C higher than on the lower shelves.
• 🥩 Middle shelves: dairy products, ready meals, sausages. The optimal area for most products.
• 🐟 Lower shelves/containers: fish, meat, perishable foods. The coldest zone (+2°...+3°C).
• 🍎 Door: drinks, oil, spices. The temperature here is the least stable (fluctuates when opened).

In the freezer, it is also recommended to distribute food into zones:

• ❄️ Upper drawer: frequently used products (ice cream, berries).
• 🥓 Bottom drawers: meat, semi-finished products, long-term storage.

How to adjust the shelves? In most models Polaris shelves are mounted on guides with locks. To change the height:

1. Lift the shelf up until it stops.
2. Tilt it towards you at an angle of 30° and remove it from the guides.
3. Install it to the desired level and fix it with a light by pressing back.

What to do if the shelf does not lock?

If the shelf does not stay on the guides, check:

1. Integrity of the clamps (they can break under excessive load).

2. Compatibility of the shelf with the model (in some series the shelves are interchangeable, but have different widths).

3. The tilt angle during installation must be at least 25°.

If the problem persists, contact the service center to replace the guides (the article number is indicated in the instructions).

6. Setting up the Polaris refrigerator depending on the season

Room temperature and air humidity affect the operation of the refrigerator. In the hot season (summer) or at low temperatures (winter), adjustments are required.

In refrigerators with climate class SN-T (for example, Polaris P 185) the compressor operation is automatically adjusted depending on the ambient temperature. If your model belongs to class N (designed for +16°...+32°C), when used in winter on an unheated balcony, hypothermia protection may be triggered (error E3).

What to do if the refrigerator does not freeze in the summer?

• 🔥 Check the room temperature - at +35°C and above the compressor may not cope. Solution: move the refrigerator to a cooler place or reduce the load.
• 💨 Make sure that the back grill is not blocked by furniture (a gap of at least 5 cm is needed for air circulation).
• ⚙️ If the model supports it, turn on the mode Summer (available in series RSM i PNF).

7. Frequent errors during setup and how to avoid them

Even experienced users sometimes make mistakes that lead to increased energy consumption or spoilage of food. Here are the most common:

• 🧊 Too low temperature in the freezer (below −20°C): leads to freezing of food and an increase in energy consumption by 15–20%. The optimal value is −18°C.
• 🚪 Frequent or prolonged opening of the door: every time you open the temperature inside. increases by 2-3°C, and the compressor takes 10-15 minutes to restore the mode.
• 🍲 Storing hot foods. dishes: placing warm food increases the load on the cooling system. Cool the dish to room temperature before storing.
• 🔌 Ignoring error signals: for example, blinking indicator Door Open may indicate not only an open door, but also a sensor malfunction.

How to reset the settings to factory settings?

If the refrigerator Polaris started to work incorrectly (for example, it does not hold the temperature or the compressor is constantly turned on), try resetting the settings:

1. Disconnect the refrigerator from the network for 5 minutes.
2. Turn it back on and immediately hold the button Mode (or Settings) 10 seconds.
3. The display will show rSt (reset). The temperature will return to factory values (+5°C in the refrigerator, −18°C in the freezer).

⚠️ Attention: After After resetting, special modes may be disabled (for example, Holiday or Super FreezeThey will have to be configured again.

8. Maintenance after setup: what to do next

Correct setup is only the first step. To ensure that the refrigerator Polaris works efficiently, follow these recommendations:

• 🧼 Cleaning the seal: wipe the rubber door gasket with soapy water. month. This will prevent the appearance of mold and ensure tightness.
• 💨 Ventilation: vacuum the rear grille (condenser) every six months. Dust accumulation increases energy consumption by 10-15%.
• ❄️ Defrosting: even in models with NoFrost it is recommended to completely defrost the freezer compartment once a year for disinfection.
• 🔋 Checking energy consumption: if the meter shows an increase in consumption, check:

- temperature in the chambers (calibration may be required);
- loading of products (overloading increases consumption);
- door condition (check the seal fits).

In refrigerators with water dispenser (for example, Polaris P 220W) it is also necessary:

• Change the filter every 6 months (or after 300 liters of water).
• Rinse the water supply system with a solution of citric acid (1 tablespoon per 1 liter of water) once every 3 months.

When to call a technician? Contact the service center if:

• The refrigerator does not cool despite the correct settings.
• The display constantly shows an error (for example, E4 - malfunction fan).
• The compressor runs non-stop for more than 24 hours.

FAQ: Answers to frequently asked questions

How to reset the E1 error on a Polaris refrigerator?

The error E1 indicates a problem with the refrigerator compartment temperature sensor. Try:

1. Turn off the refrigerator for 10 minutes, then turn it on.
2. Check whether the food is blocking the air circulation near the sensor (usually it is located on the back wall).
3. If the error repeats, the sensor needs to be replaced (contact service).

Is it possible to turn off the sound signal when the door is open?

Yes, in most models the signal is turned off by holding the button Alarm (or Sound) for 3-5 seconds. In refrigerators without a separate button, use the combination Mode + Temp. Please note: turning off the signal may result in an increase in temperature if the door is accidentally left open.

Why is the Polaris refrigerator very noisy?

The noise can be caused by:

• Uneven installation (casing vibration).
• Touching the compressor tubes to the rear wall (check the gap).
• Fan operation in models with NoFrost (normal noise - up to 45 dB).
• Compressor malfunction (if the noise is accompanied by overheating or shutdowns).

If the noise appears suddenly, check if it is in is there a foreign object in the ventilation holes.

How to enable the "Holiday" mode on a model without a Holiday button?

In refrigerators Polaris without a separate button Holiday the mode is activated by the combination:

1. Press and hold Mode (or Settings) 5 seconds.
2. Use the buttons +/– select Holiday.
3. Confirm the selection with the button OK.

In mechanical models There is no "Vacation" mode - just set the regulator to minimum cooling (1-2).

How long does it take the Polaris refrigerator to reach the temperature after turning on?

The time depends on the model and conditions:

• NoFrost: 2-4 hours until the freezer reaches −18°C.
• Direct Cool: 4–6 hours (due to manual defrosting).
• At room temperatures above +30°C, the time may increase by 30–50%.

Do not load food until a stable temperature indicator appears on the display (usually a green LED or inscription OK).