Setting the temperature in the Atlant two-chamber refrigerator after defrosting: instructions with photos and advice

• If the refrigerator compartment is too warm, increase the value by 1 division.
• If the products freeze slightly, reduce by 1 division.

In models Atlant with one regulator (for example, MHM 1708), the adjustment is carried out with a single knob. In this case:

• Position 1–2 —minimum cooling (suitable for winter or cool rooms).
• Position 3–5 — optimal mode for most conditions.
• Position 6–7 —maximum cooling (only needed in hot weather or when loading a large amount of warm products).

Place the thermometer in a glass of water (for the refrigerator compartment)| Place the thermometer between the products in freezer|Close the door and wait 2-3 hours|Compare the readings with the recommended values|Adjust the settings if necessary-->

Please note: in refrigerators Atlant with mechanical controls there is no indication of the current temperature. Therefore, without a thermometer, you will not be able to know exactly how many degrees there are in the chamber. If there is no thermometer, focus on the condition of the products:

• 🥛 Milk does not sour for 3-4 days - the temperature is normal.
• 🍎 Fruits are not covered with ice - the cooling is not excessive.
• ❄️ The ice cream remains hard - the freezer is working correctly.

Setting the temperature in Atlant refrigerators with electronic control

Electronic control panels are installed in modern models Atlantsuch as XM 6025-031, XM 4626-000 or XM 4426-000. They allow you to set precise temperatures in 1°C increments, and are often equipped with a display showing the current values. Advantages of electronic control:

• 🎛️ Precise adjustment without guesswork (for example, you can set it exactly +3,5°C).
• 📊 Display of the current temperature in both chambers.
• ⚡ Quick freezing functions or cooling.
• 🔔 Alarm when the door is open or temperature fluctuations.

Setting instructions for the electronic panel:

1. Press the button Power or On/Offto turn on the refrigerator (if it was turned off).
2. For the refrigerator compartment:
   • Press the button Fridge or Refrigerator (may be indicated by a snowflake ❄️).
   • Use the buttons +/– set the value +4°C.

• Press the button Freezer or Freezer (may be indicated by an asterisk ⭐).
• Use the +/– buttons to set the value -18°C.
• If there is a function Super Freeze or Quick freezing, disable it via 24 hours (it is only needed for instant cooling of large volumes of food).
• Press OK or Setto save the settings.

On some models (for example, Atlant XM 6025-031) there is a mode Holiday. It is activated by a button Vacation and maintains the temperature around +12°C in the refrigerator compartment, saving energy. Use it if you are leaving for a long time.

Important: After changing settings, wait 6-8 hours before checking the temperature. Electronic sensors may not show accurate values the first few cycles of compressor operation.

Typical errors when setting the temperature after defrosting

Even experienced users sometimes make mistakes that lead to incorrect operation. refrigerator. Here are the most common:

1. Setting maximum cooling “just in case”

   Many people believe that the colder the better. However, the lower the temperature in the freezer or in the refrigerator leads to: -20°C in the freezer or +2°C in the refrigerator compartment leads to:

   • ❄️ Icing of products (meat loses its taste, fruits become watery).
   • ⚡ Increased energy consumption (the compressor works without interruptions).
   • 🔊 Increased noise (fans in models with No Frost work at limit).

Optimal: -18°C in the freezer and +4°C in the refrigerator.

• Ignoring external conditions

  The temperature in the refrigerator depends on the climate in the room. In summer or in a stuffy room (for example, in a kitchen with a stove), you need to increase the cooling power by 1-2 steps. In winter, especially if the refrigerator is on the balcony, you need to reduce it.

• Overloading the chambers with food immediately after defrosting

  If you load warm food (for example, just cooked dishes) immediately after turning on, the compressor will not cope with the load. chambers will rise, and the compressor may overheat.

  Correct order:

  1. Turn on the refrigerator and let it run for 1-2 hours empty.
  2. Load food in small batches, starting with the coldest ones.
  3. Do not put in hot dishes in the freezer - cool them to room temperature.

If the seal is worn out or the door is skewed, cold air leaves and warm air gets inside. This leads to:

• 📈 Constant operation. compressor.
• ❄️ Ice formation on the back wall (in models with a drip system).
• 💧 Condensation on the products.

Check the seal: take a sheet of paper, close the door and try to pull out the sheet. If it comes out easily, the seal needs to be cleaned or cleaned. change.

1. Correct connection to the network (voltage should be 220–240 V).

2. Condition of the thermostat (if it breaks, it must be replaced).

3. Cleanliness of the condenser (dust on the back wall impairs heat transfer).-->

How to check that the temperature is set correctly

Even if you followed the instructions, it would be useful to make sure that the refrigerator is working correctly. Here's how to do it:

1. Use a thermometer

   The most reliable way is to measure the temperature in both chambers:

   • Place an outdoor thermometer in a glass of water (for the refrigerator).
   • Put the second thermometer between the foods in the freezer.
   • Close the door and wait 6-8 hours.
   • Compare the readings with the recommended values.

   If the difference is more than 2°C, adjust the settings.

2. Assess the condition of the products

   Some products serve as natural temperature indicators:

   • 🥛 Milk - should not turn sour within 3-4 days at +4°C.
   • 🍌 Bananas —should not turn black faster than in 5–7 days.
   • 🥩 Fresh meat —should not be covered with ice or mucus.
   • ❄️ Ice cream —should remain hard, but not “stone”.
3. Listen to the compressor

   Normally, the compressor should:

   • Work in cycles: 10–20 minutes on, Rest for 20–30 minutes.
   • Do not make any extraneous sounds (knocking, grinding, loud humming).
   • Do not get too hot (maximum - warm to the touch).

If the compressor works without stopping or is too noisy, this is a sign of incorrect settings or malfunction.

• Check the formation of condensation

  In refrigerators with drip system a small layer of frost or drops of water may appear on the back wall - this is normal, however, if:

  • 💧 Water accumulates at the bottom of the chamber - check the drain hole (it could be clogged).
  • ❄️ Ice more than 5 mm thick forms on the walls - the temperature is too low or the seal is not airtight.

  If problems are revealed after checking, do not rush to call a technician:

  • Adjust the legs of the refrigerator (it should stand level, without distortions).
  • Clean the ventilation holes (in models with No Frost).
  • Redistribute the products (do not place them close to the back wall).
  How to check the tightness of the door without thermometer?

  Turn on the flashlight, place it inside the refrigerator and close the door. If the light is visible in the dark, the seal is letting air through. You can also use a thin sheet of paper: if it is easily pulled out from under the closed door, the seal is broken.

  What to do if the temperature does not stabilize

  If, after defrosting and adjusting, the temperature in the refrigerator Atlant jumps or does not correspond to the specified parameters, the reasons may be the following:

  Problem	Possible cause	Solution
  The temperature in the refrigerator compartment is too high	The door does not close tightly Thermostat is broken The compressor is not working efficiently	Check the seal and door hinges Replace the thermostat (if the control knob does not affect the temperature) Clean the condenser from dust
  The freezer does not freeze, but the refrigerator compartment works	Freon leakage Clogged capillary tube Fan failure (in models with No Frost)	Call a technician for diagnostics Check whether the fan is iced up
  The compressor is running non-stop	The room temperature is too high Thermostat is stuck in position "on" Refrigerant leak	Reduce the temperature on the regulator Check if the compressor is hot (if so, turn off the refrigerator and call a technician)
  There is an error on the display E1, E2 or the indicator is flashing	Temperature sensor malfunction Problems with the electronic unit	Turn off the refrigerator for 10 minutes, then turn it on again If the error remains, contact the service center

  If the refrigerator Atlant is new and still under warranty, do not try to repair it yourself. Contact an authorized service center. For models older than 5 years, it is easier and cheaper to replace faulty parts (for example, a thermostat or seal) yourself.

  In Atlant refrigerators with electronic control, error E1 often indicates a problem with the refrigerator compartment sensor, and E2 - the freezer one. Before the technician’s visit, try resetting the settings to factory defaults (usually this is done by holding the “Set” or “Mode” button for 5 seconds).

  1. Reliability of connection to the outlet (sometimes the plug comes off due to vibrations of the compressor).

  2. Presence of voltage in the network (perhaps the circuit breaker on the panel has tripped).

  3. State of the fuse (in some models it is located on the compressor).-->

  Tips for maintaining optimal temperature

  To ensure that the refrigerator Atlant works efficiently and the food stays fresh longer, follow these recommendations:

  • 📦 Do not overload the chambers —there should be space between products for air circulation. Optimal loading: 2/3 of the volume.
  • 🔄 Do not put hot dishes - cool them to room temperature, otherwise the temperature in the chamber will rise sharply.
  • 🧊 Use containers - open liquids (soups, milk) increase humidity, which leads to icing.
  • 🌡️ Check the temperature regularly —at least once a month, place the thermometer in the refrigerator for several hours.
  • 🧹 Clean the back wall —dust on the condenser impairs heat transfer and causes the compressor works harder.
  • 🚪 Minimize the time the door is open —each time you open the temperature inside rises by 2-3°C.

  For models with No Frost additionally:

  • 🌀 Once every 6 months, clean the ventilation holes from dust (use a vacuum cleaner or soft brush).
  • ❄️ If ice appears on the walls, defrost the refrigerator for 10–12 hours (despite the stated “no” function defrosting", sometimes this is necessary).

  For models with drip system:

  • 💧 Once a month, clean the drain hole (it is located on the back wall of the refrigerator compartment).
  • 🧽 Wipe the walls from condensation with a dry a rag.

  If you live in a hot climate or the refrigerator is located next to the stove, install an additional fan to cool the back wall. This will reduce the load on the compressor and extend the service life of the equipment.

  FAQ: Frequently asked questions about setting the temperature in the Atlant refrigerator

  How often do you need to defrost an Atlant refrigerator with a drip system?

  Refrigerators Atlant With a drip system, it is recommended to defrost 1-2 times a year, even if the ice is not visible. This is because condensation can accumulate in hidden places (such as in the drainage system), resulting in an unpleasant odor or incorrect operation. If ice forms on the back wall then