Modern refrigerators Samsung with displays on the door are complex electronic systems that allow flexible control of temperature conditions. Owners are often faced with a situation where it is necessary to temporarily change the functionality of one of the chambers, for example, turn the freezer into a refrigerator compartment or turn it off completely for defrosting and washing.
The question of how to turn off the freezer is not as simple as it seems at first glance, since in most models complete shutdown of the compressor through the control panel it is impossible without turning off the appliance itself from sockets However, there are a number of software modes, such as Cool Select+, which allow you to ignore standard freezing and maintain a positive temperature.
In this article we will analyze in detail software methods for changing the operation of the chamber, manual methods of shutting down and the nuances of operating smart refrigerators. You will learn which buttons to press, how to interpret the indications on the screen and what absolutely cannot be done so as not to damage the No Frost system No Frost system.
Fundamental limitations of Samsung electronics
Before you start manipulating the buttons, it is important to understand the architecture of your refrigerator. In models with a display, control is carried out through electronic control unit, which receives signals from many sensors. The panel on the door is only an input interface, and not a direct switch for the physical components.
When you try to "turn off" the camera, you are actually changing the target temperature you are supposed to maintain inverter compressor. The electronics Samsung are designed to minimize equipment wear, so sudden changes in temperature conditions are blocked by software protection algorithms.
It is worth noting that in two-chamber models with one compressor (and these are the majority) it is physically impossible to turn off the cooling in one chamber, leaving the other work without the use of special dampers or independent circuits. This is where software solutions come to the rescue.
⚠️ Attention: An attempt to programmatically “turn off” a camera that is not structurally designed to operate in positive mode can lead to freezing of the evaporator and failure of the defrost sensor.
Using the Cool Select+ mode to change functions
The most civilized way to change the operation of the freezer is to use the function Cool Select+ (or a similar one, depending on the series, for example, Flex Zone). This mode allows you to transform the freezer into an additional refrigeration compartment or area for storing products that require special temperature conditions.
To activate the mode, you need to find a button with the corresponding name or icon on the control panel. In some models Samsung with a touch screen, you need to press and hold the button Freezer for 3 seconds until the indicator lights up Cool Select+.
After activating the mode, you can choose from the set temperatures. The following options are usually available:
- 🥩 Meat/Fish (Meat/Fish): Temperature about -1°C, ideal for short-term storage of fresh meat without freezing.
- 🍺 Cold Drink (Cooling drinks): Mode about +5°C, turning the freezer into a bar area.
- 🥦 Vegetable (Vegetables): Mode about +3°C, allowing you to store large volumes of vegetables that do not fit into the main chamber.
- 🧊 Soft Freeze: Temperature -5°C, products do not freeze into stone and can be cut knife.
Switching between modes is carried out by pressing the button again Cool Select+ or by cyclically switching the indicators on the display. It is important to wait for a confirmation signal (usually a beep or flashing screen) before releasing the button.
Manually setting the temperature through the control panel
If the mode Cool Select+ is not available in your model or you want to set the exact temperature manually, you can use standard controls. The display Samsung usually shows two values: for the refrigerator (Fridge) and freezer (Freezer) chambers.
To change the settings, press the button Freezer. The numbers on the display will begin to flash, signaling that they are ready to enter. Use the same button or the arrow buttons (up/down) to change the value.
The standard freezer adjustment range is -15°C to -23°C. However, if you want to "shut down" your freezer as much as possible, you should try to set the temperature to the highest possible temperature. In some engineering menus or models, this value can be increased to -1°C or even +1°C, but most often the electronics will limit you to -15°C.
Why can’t you set +5°C in a regular freezer?
The design of the evaporator and fan in the freezer is designed for low temperatures. When operating in positive mode without special protection, a “crying” effect may occur when the condensate does not have time to evaporate and turns into an ice crust at the bottom of the chamber.
After selecting the desired parameter, do not press other buttons for 5 seconds. The system will automatically save the setting and the display will stop flashing. The compressor will start working according to a new algorithm.
Complete shutdown and defrosting (Power Freeze/Power Cool)
Often, by the phrase “turn off the freezer,” users understand the need to defrost it. In refrigerators Samsung with a system No Frost full defrosting is rarely required, but during general cleaning or long-term departure it is necessary.
To force defrost or stop the camera, it is best to use the function Power Freeze in the reverse order, although the direct mode "Defrost" on the front panel usually not. The most reliable way is physical disconnection.
However, there is a nuance with the sensors. If you simply turn your refrigerator off and then back on, it may not start the defrost cycle right away. Some models have a hidden service mode, but it is intended for craftsmen.
- ❄️ Natural defrosting: Unplug the device, open the doors and leave for 12-24 hours.
- 💨 Accelerated defrosting: Use a fan to circulate air, but do not use a hair dryer (risk of damage plastic).
- 🧼 Hygiene: After defrosting, be sure to wipe the chamber with a soda solution to remove odors.
Remember that frequent complete shutdowns are harmful to the compressor. The oil in the compressor thickens, and a sudden start may cause the effect of hydraulic shock.
☑️ Correct defrosting of Samsung
Table of temperature conditions and their influence
Understanding how different settings affect the operation of the unit will help you avoid mistakes. Below is a table showing the dependence of the system operation on the selected parameters.
| Mode / Setting | Temperature range | Influence on the compressor | Recommended use |
|---|---|---|---|
| Standard Freezer | -19°C... -23°C | Normal cyclic operation | Long-term storage, freezing |
| Cool Select+ (Meat) | -1°C... +1°C | Enhanced fan operation | Short-term storage of fresh meat |
| Cool Select+ (Drinks) | +3°C... +5°C | Reduced load | Parties, beverage storage |
| Power Freeze | Maximum cooling | Continuous operation 24-72 hours | Quick freezing of large volumes |
Using modes with increased temperatures in the freezer can lead to the fact that the products in the main chamber also slightly change the storage temperature due to the flow of air masses, if the model does not double-circuit.
⚠️ Attention: Do not store in Cool Select+ products that require deep freezing (for example, ice cream or dumplings for a long time) for more than 2-3 days.
Typical errors when setting up the display
Users often make mistakes when trying to control complex electronics Samsung like a conventional mechanical thermostat. One of the common problems is the control panel being locked.
If the lock icon is lit on the display, any actions you take to change the temperature will be ignored. To unlock, you need to find the button Child Lock (often indicated by the image of a key or lock) and hold it for 3 seconds until a characteristic sound signal is heard.
Another mistake is an attempt to set the temperature higher than the recommended one without turning on the corresponding mode. If you simply set it to -5°C in normal mode, the refrigerator may not work correctly, since the algorithm No Frost will try to compensate for the "heat" by constantly turning on the compressor.
You should also avoid changing modes frequently. Going from -20°C to +3°C and back again places a huge thermal load on the insulation and the compressor. Allow the system to stabilize for 24 hours after changing the settings.
Diagnosing problems after changing the settings
After you have tried to turn off or reconfigure the freezer, you need to monitor the behavior of the unit. Incorrect settings can lead to error codes appearing on the display.
The most common codes associated with temperature sensors are: 11C, 13C, 14C (freezer sensor error). This may mean that the sensor is “stuck” or shows incorrect data after a sudden change in mode.
If you notice that:
- 🔊 The refrigerator is humming louder than usual: The fan may be working too hard, trying to cool the chamber to impossible values.
- 💧 Water has appeared on the floor: The defrost system cannot cope with condensation at above-zero temperatures in the freezer.
- 🌡️ The food in the main chamber is spoiling: The temperature balance between the compartments is disrupted.
B In such cases, it is recommended to reset the settings to factory settings (usually by holding down a combination of buttons, for example Freezer + Fridge for 10-15 seconds, but it is better to check the exact combination in the instructions for the specific model) and reboot the device.
Frequently asked questions (FAQ)
Can I turn it off completely? freezer button, leaving the refrigerator working?
In the vast majority of models Samsung with one compressor, completely turn off the freezer, leaving the refrigerator compartment running impossible. The design implies their joint work. The maximum that can be done is to raise the temperature in the freezer to the minimum possible (about -1°C) through the mode Cool Select+, turning it into a refrigerator.
Why did the refrigerator start to work loudly after changing the settings?
When changing the target temperature, the compressor takes time, to stabilize the climate inside the chambers. If you suddenly increase the temperature (for example, from -18°C to -5°C), the system may work in intensive mode for some time or, conversely, rarely turn on, which may be perceived as a change in the background sound. Also check that the refrigerator is not adjacent to the wall.
What to do if the display shows flashing numbers?
Flashing numbers on the display Samsung usually mean that the temperature setting process is in progress, but you have not confirmed the choice. If already set values are flashing or an error code is lit (for example, 88, 85, 11C), this is a malfunction signal. Try defrosting the refrigerator within 24 hours. If the error remains, you need to call a technician.
Is it safe to keep the freezer in +3°C mode all the time?
Using the Cool Select+ (Vegetable/Cold Drink) mode on an ongoing basis is permissible if this is provided for in the instructions for your model. However, the seals and insulation of the freezer are designed to withstand low temperatures. With constant operation in positive mode, rubber seals may age faster due to the absence of deep freezing of moisture, which usually “preserves” the rubber.