We rehang the doors of the Biryusa refrigerator yourself: instructions with photos and tips

Re-hanging the refrigerator doors Biryusa is a task that sooner or later almost every owner of this equipment faces. The reasons may be different: inconvenient opening due to the layout of the kitchen, a change in the arrangement of furniture, or a banal desire to update the interior. Fortunately, the manufacturer has provided this option for most models, and you can get the job done without calling a specialist.

In this article we will figure out how to properly rehang the doors on refrigerators Biryusa of different series - from classic single-chamber to modern two-chamber models with system No Frost. You will learn what tools you will need, how to avoid common mistakes and what to do if the door does not close properly after rehanging. We will also tell you in which cases it is better not to take risks and turn to professionals.

Important: the process of rehanging doors on refrigerators Biryusa has its own nuances depending on the model and year of manufacture. For example, old Soviet refrigerators (before the 2000s) may have fasteners that differ from modern ones. If your model was released before 2010, be sure to check the availability of spare hinges in the kit - their design may have changed.

1. Preparing for work: tools and safety measures

Before you start rehanging the doors, prepare everything you need. Without the right tools, you risk damaging the fasteners or the door itself. Here's what you'll need:

• 🔧 Phillips screwdriver (size PH2 is usually suitable) - for most modern models.
• 🔧 Flat screwdriver (3-5 mm) - can be useful for old refrigerators or decorative plugs.
• 🔧 Wrench (usually 10 or 13 mm) - for models with metal hinges.
• 📏 Ruler or tape measure - to check the gaps after installation.
• 🧲 Magnet (optional) - will help hold small parts (screws, washers).
• 🧴 Silicone grease —for processing hinges after rehanging.
• 📸 Smartphone —for photographing the process (useful if you have to return the doors to their place).

Also prepare your workspace:

• 🚪 Give access to the refrigerator from all sides - you will need to tilt it.
• 🧊 Unplug the refrigerator and defrost (if it is not No Frost).
• 📦 Remove all products and shelves from the door - they may get in the way or fall.
• 🧹 Place a soft cloth or cardboard under the door to avoid scratching the floor when removing.

⚠️ Attention: If your refrigerator Biryusa has an electronic control (for example, model Biryusa-130 or Biryusa-22K, before re-hanging the doors required unplug it for 10-15 minutes. This will reset possible sensor errors that may occur when changing the door position.

It would be a good idea to look at the instructions for your model - there may be a fastening diagram. If there are no instructions, it doesn’t matter: most. refrigerators Biryusa have a standard hinge design. The exception is models with dispenser for water (for example, Biryusa-26S), where you will additionally have to reinstall the tubes.

2. Determine the type of door fastening on your model

Refrigerators Biryusa can be divided into three groups according to the type of door fastening:

To determine the type of fastening on your model, inspect the hinges:

• 🔍 If you can see the screws on the side or on top of the hinge - you have a standard mount.
• 🔍 If the bottom hinge has a round pin sticking out of the body - this is a hinged mount.
• 🔍 If there are no hinges visible, but there are plastic plugs - these are hidden loops.

⚠️ Attention: For models Biryusa s No Frost system (for example, Biryusa-139 or Biryusa-26C) when outweighed doors, the tightness of the seal may be compromised. After work, be sure to check whether cracks have appeared - if so, the seal needs heat with a hairdryer (temperature 50–60°C) and leveled.

If you are not sure about the type of fastening, you can use a simple test: try slightly lifting the door when closed condition. If it “plays” on the bottom hinge, it’s a hinged type. If it doesn’t move, it’s most likely a standard screw hinge.

How to find out the exact model of the Biryusa refrigerator?

The exact model is indicated on the nameplate (metal plate) on the back or inside the refrigerator. Usually it begins with the letters “Biryusa-” or “B”. followed by numbers (for example, Biryusa-18 or B-130). If the nameplate has been erased, look in the instructions or on the box (if it is still there). screw hinges (for example,

3. Step-by-step instructions: hanging the door on standard hinges

Let's consider the most common option - refrigerators Biryusa with screw hinges (for example, Biryusa-6, Biryusa-18, Biryusa-22). This method is also suitable for most two-chamber models with a freezer on top.

Step 1. Remove the top hinge.

1. Open the refrigerator door 90 degrees and prop it up (for example, a chair).
2. On the top, where the hinge is attached to the body, unscrew the screws (usually 2-3 pieces).
3. Carefully remove the decorative cover (if any) - it may be latched.
4. Unscrew the screws securing the hinge to the door itself (usually from the bottom of the hinge).

Step 2. Remove the bottom hinge.

1. Holding the door, unscrew the screws on the bottom hinge (first from the body, then from the door).
2. If the hinge is hinged (with a pin), carefully remove the pin from its socket by pulling the door up.
3. Remove the door and place it on a soft surface (for example, blanket).

Step 3. Prepare holes for the loops on the other side.

On most models Turkish there are already holes for the loops on both sides - they are closed with plugs. You need:

1. Remove the plugs on the opposite side (pry them off with a flat screwdriver).
2. Move the rubber seal to the other side (if it is not symmetrical).
3. Check whether the holes match hinges - if not, drilling may be required (but this is rare for Turk Biryusy).

Step 4. Install the hinges on the new side.

1. Screw the bottom hinge to the door, then insert the pin (if there is one) into the socket on the body.
2. Install the top hinge, first securing it to the door, then to the body.
3. Tighten all the screws, but not all the way - then you will need to adjust.

Step 5. Adjust the door.

After installation, check:

• 🔹 The door should open smoothly, without creaking.
• 🔹 The gaps around the perimeter should be the same (2-3 mm).
• 🔹 The seal should fit snugly - check with a sheet of paper (it should not fall out when the door is closed).

4. Features of hanging doors on Biryusa two-chamber refrigerators

Two-chamber refrigerators Biryusa (for example, Biryusa-10, Biryusa-20, Biryusa-26S) take more time, since you will have to re-hang both doors - the refrigerator and freezer compartments. The main rule: start from the top door (freezer, if it is on top), then go to the bottom.

Algorithm of actions:

1. Remove the top door (freezer) according to the instructions from the previous section.
2. Move the middle hinge (it secures both doors) to the other side.
3. Install the top door to a new place, but do not tighten the screws until end.
4. Remove the bottom door (refrigerator compartment) and move the hinges.
5. Install the bottom dooraligning it with the top.
6. Adjust the gaps between the doors (should be 3-5 mm).

Features for different models:

• 🔹 On Biryusa-10 i Biryusa-20 the middle loop is attached to the body with four screws —don’t lose them!
• 🔹 There is Biryusa-26S s No Frost on the freezer door seal heating element — when rehanging, do not damage its wires.
• 🔹 On models with water dispenser (Biryusa-50) you will have to reinstall the water supply tubes.

⚠️ Attention: If, after re-hanging the doors on a two-chamber refrigerator Biryusa the freezer begins freeze more, check whether the middle hinge is warped. It is responsible for the tightness between the chambers - if there is a gap, cold air will penetrate into the fridge compartment, causing the compressor to work harder.

For models s electronic display (for example, Biryusa-139) after reweighing may be required reset settings. To do this:

1. Unplug the refrigerator for 5 minutes.
2. Turn on and press at the same time buttons Super and Fridge (if available) for 5 seconds.
3. Wait until the display reboots.

5. Typical mistakes and how to avoid them

Even with the apparent simplicity of the process, many make mistakes that then have to be corrected. Here are the most common:

Another common problem is creaking hinges after rehanging. This happens due to:

• 🔹 Lack of lubrication —the hinges need to be lubricated with silicone grease (not oil!).
• 🔹 The door is skewed —check whether it hangs evenly.
• 🔹 Garbage ingress into the hinges - clean the hinges with a dry cloth.

If after rehanging the refrigerator becomes make more noise, check:

• 🔹 Does the door touch the housing when opening/closing.
• 🔹 Are the compressor fastenings loose (vibration can be transmitted to the door).
• 🔹 Is the seal displaced (sometimes it touches the internal details).

6. When it’s better not to risk it and call a specialist

Although re-hanging the doors on the refrigerator Biryusa is a feasible task for most, there are cases when it is better to turn to a professional:

• 🔧 Your refrigerator under warranty —self-repair may invalidate it.
• 🔧 Model with electronic control and display (for example, Biryusa-139), if you are not sure of the settings.
• 🔧 Refrigerator with built-in ice maker or dispenser —tubes will need to be reinstalled.
• 🔧 If, when removing the door, you found rust on the hinges or body - they may need to be replaced.
• 🔧 Door after rehanging does not stay on the hinges (possibly worn hinges).

It is also worth calling a specialist if:

• 🔹 You cannot find the holes for the hinges on the other side (they may need to be drilled).
• 🔹 After rehanging refrigerator does not turn on (sensor wires could be damaged).
• 🔹 The seal is torn or deformed - replacing it requires special skills.

Cost of re-hanging refrigerator doors Biryusa in service centers is usually 1500–3000 rubles (depending on the model and region). If you are not confident in your abilities, sometimes it is cheaper and safer to entrust the work to a professional than to risk expensive repairs.

⚠️ Attention: On some models Biryusa (for example, Biryusa-3 or Biryusa-6) the hinges wear out over time and may burst when overweighted. If your refrigerator is more than 10 years old, before work, inspect the metal hinges - if there are cracks, it is better to replace them in advance.

7. Caring for doors after rehanging

To ensure that refrigerator doors Biryusa last for a long time after rehanging, follow these tips:

• 🧼 Clean the seal 1-2 times a month with warm water and soap. Do not use abrasive detergents!
• 🛢️ Lubricate the hinges with silicone grease every six months (not oil - it collects dust).
• 🧲 Check the seal magnet - if it is weakened, the door will close worse. You can check with a sheet of paper: if it falls out when the door is closed, the seal needs to be replaced.
• 🔧 Tighten the hinges once a year - over time they become loose.
• 🚪 Do not slam the door - this will deform hinges and seal.

If the seal has lost its elasticity, you can try restore it:

1. Remove the seal (it is secured with latches or screws).
2. Place it in a bowl of hot water (60–70°C) for 10–15 minutes.
3. Dry and install back.

For models with No Frost (for example, Biryusa-26S) after rehanging the doors recommended:

• 🔹 Check the operation of the fan - it should not touch the door.
• 🔹 Make sure that the heating element of the seal (if any) is connected correctly.
• 🔹 Carry out a defrost test cycle to make sure it is sealed.

FAQ: Frequently asked questions about reversing the doors of the Biryusa refrigerator

Is it possible to rehang the doors on the Biryusa-3 refrigerator (Soviet model)?

Yes, but there are nuances: in older models Biryusa-3 the hinges often rust and can break when removed. Before work, treat them with WD-40 and let them sit for 10-15 minutes. Also, these models may not have ready-made holes on the other side - you will have to drill (diameter 6–8 mm).

After rehanging, the door of the Biryusa-18 refrigerator does not close tightly. What to do?

Most likely, the problem is in the seal or adjustment of the hinges. Check:

1. The tension of the seal - it should be evenly pressed along the entire perimeter.
2. The tightening of the hinges - loosen the top or bottom half a turn and check again.
3. Is there any skew of the door - the gaps should be the same (2-3 mm).

If the seal is old, you can heat it with a hairdryer (temperature 50–60°C) - it will become more elastic.

Do you need to defrost the Biryusa refrigerator before hanging the doors?

If you have a model with drip system (not No Frost), then yes - defrost the refrigerator 12-24 hours before work. This is necessary in order to:

• Prevent water from getting on electrical parts when removing the door.
• Easily access the hinges (ice can interfere).
• Avoid deformation of the seal during sudden changes temperature.

For models with No Frost defrosting is not necessary, but it is recommended to unplug the refrigerator for 1-2 hours before use.

Is it possible to rehang only the top door on a two-chamber refrigerator Biryusa-20?

Technically it is possible, but Not recommended. On two-chamber models, the upper and lower doors are connected by a middle hinge. If you rehang only the upper door and leave the lower one in place, problems will arise:

• Mismatch of gaps between the doors.
• Distortion of the middle hinge.
• Deterioration of the tightness of the freezer cameras.

It is better to hang both doors at once. If you only need to change the opening side of the top door, consider the option of installation of additional hinges (these can be ordered from the manufacturer).

Where can you buy spare hinges for the Biryusa refrigerator?

Spare hinges for refrigerators Biryusa can be found:

• 🔹 In official service centers (the most reliable option, but more expensive).
• 🔹 On AliExpress or Wildberries —search by refrigerator model.
• 🔹 In shops of spare parts for household appliances (for example, "220 Volt", "M-Video").
• 🔹 On Avito or Yule they often sell used parts from disassembled refrigerators.

The cost of hinges is from 300 to 1500 rubles per set (depending on the model). When purchasing, check whether the hinge is suitable for your opening side (left/right).