We rehang the Indesit refrigerator door yourself: instructions with photos and tips

Re-hanging the refrigerator door Indesit is a task that many owners face when moving, renovating a kitchen, or simply wanting to optimize space. Unlike models from other brands, equipment from the Italian manufacturer has its own design features: from the location of the hinges to the type of fastenings. This article will help you figure out how to correctly throw the door without the risk of damaging the seal or mechanism, even if you have never held a screwdriver in your hands.

It is important to understand that the procedure is different for refrigerators with freezer compartment on top (for example, series BIAA 13 or C 132) and models like Side-by-Side or with a bottom freezer (like Indesit ITF 118). We will analyze both options in detail, point out problems (for example, overtightening of bolts or incorrect installation of plugs) and provide a checklist for checking the result. You will also find out which tools are really needed and what you can do without. typical mistakes (for example, overtightening of bolts or incorrect installation of plugs) and we will give a checklist to check the result. You will also learn which tools are really needed and which you can do without.

If your refrigerator is under warranty - rehanging the door can invalidate it, as it requires the removal of factory seals. Check this point with the service center Indesit before starting work. For models older than 5 years, the procedure is absolutely safe and will save you 1,500–3,000 rubles (the average cost of the service in service centers).

Preparation: tools and conditions

Before To get started, make sure you have everything you need. For most models Indesit you will need:

• ✅ Phillips screwdriver (preferably magnetic so as not to lose small screws).
• ✅ Hex 5 mm - for some models with a bottom freezer.
• ✅ Flat screwdriver or a plastic spatula for removing decorative plugs.
• ✅ Wrench 10 mm - if the hinges are secured with nuts (relevant for older models).
• ✅ Making tape - to secure the door during work.
• ✅ Level (optional) - to check the evenness of the installation.

Some "craftsmen" advise using a drill to speed up the process, but this extremely risky: you can damage the case or break the threads in the hinges. All fastenings in refrigerators Indesit are designed for hand tools.

Also prepare your work space:

• 📏 Clear at least 1 m² around the refrigerator - the door will have to be removed completely.
• 🧹 Lay down a soft cloth or cardboard so as not to scratch the floor or the door itself.
• 🔌 Unplug the refrigerator 1-2 hours before work to defrost the seal - it will become more elastic.

Weighing scheme for models with a freezer on top

This configuration is the most common in the lines Indesit (for example, BIAA 13, C 132, T 16). Here, the door of the refrigerator and freezer are mounted on common hinges, which simplifies the process. Follow the step-by-step instructions:

1. Remove the decorative plugs from the loops. They are attached with latches - use a flat-head screwdriver to pry them off from the side. In some models, the plugs are glued; if they do not lend themselves, heat them with a hairdryer (not higher than 60°C) so that the glue softens.
2. Unscrew the top hinge of the refrigerator compartment. Usually it is fixed with 2-3 screws using a Phillips screwdriver. Hold the door so that it does not fall.
3. Remove the refrigerator door and carefully place it on the prepared surface (face up).
4. Unscrew the middle hinge (connects the freezer and refrigerator). There may be screws or nuts here - use a hexagon or wrench.
5. Remove the freezer door and also place it next to it.
6. Move the hinges to the opposite side. On the refrigerator body and doors there are symmetrical holes for fastenings (usually closed with plugs).
7. Install the doors in the reverse orderstarting with the freezer.

Important nuance: in models Indesit with No Frost (for example, Indesit ITF 118 W) there are air ductbetween the doors. When rehanging, make sure that it remains on the side of the hinges - otherwise the defrosting system will not work correctly.

Take a photo of the location of the hinges and plugs|

Disconnect the refrigerator from the mains|

Prepare tools and soft bedding|

Check for the presence of symmetrical holes on the opposite side-->

Features for refrigerators with bottom freezer

Models like Indesit ITF 118, ITF 120 or ITF 121 have a different design: the freezer is located at the bottom, and the hinges are separated. Here the algorithm is more complicated:

1. Remove the top door (refrigerator compartment), as described above.
2. Unscrew the bottom hinge of the freezer. In some models, it is hidden under a decorative panel - it must first be removed (usually held on by 2-3 latches).
3. Carefully remove the freezer door. It is heavier than the top one due to the thick layer of insulation.
4. Move the bottom hinge to the opposite side. Here you may need hinge extensions (come with the refrigerator or purchased separately). Without them, the door will not fit tightly.
5. Install the doors in the reverse orderstarting from the bottom.

In models with Total No Frost (for example, Indesit ITF 120 W) after reweighing, resetting the door closing sensormay be required. It is located on the top hinge and sometimes works falsely if the door is not perfectly level. You can check this by closing the refrigerator and listening: if after 1-2 minutes a beep is heard, the sensor needs to be adjusted (instructions in the “Typical problems” section).

Where can I get hinge extensions?

If included with the refrigerator There were no extension cords; they can be ordered according to the model number (indicated on the nameplate on the back) or bought as universal ones in spare parts stores for household appliances. The average price is 300–500 rubles per set.

Adjusting doors after rehanging

Even if you did everything correctly, the door may close poorly or sag. This is normal - almost all refrigerators Indesit require additional settings. Here's how to do it:

1. Check the horizontal level. Use a spirit level, placing it on the top edge of the door. If there is misalignment, tighten or loosen the screws on the top hinge.
2. Adjust the fit of the seal. Close the refrigerator and try to insert a piece of paper between the door and the body. If it falls out, the seal does not fit well. Tighten the screws on the hinges (clockwise - presses harder, against - loosens).
3. Check the operation of the magnetic seal. To do this, open the door 45° and release. It should close on its own. If not, you need to adjust the lower loop.

In models with electronic display (for example, Indesit ITF 121 W) after re-weighing, the calibration of the temperature sensor may be lost. To reset the error, press and hold the Super Cool (or Super Freeze) button for 10 seconds until a beep sounds.

Typical mistakes and how to avoid them

Even experienced craftsmen sometimes make mistakes when rehanging doors Indesit. Here are the most common:

• ❌ Ignoring symmetrical holes. On the opposite side of the door and body there should be technological holes for hinges. If they are not there, the model is not intended for rehanging!
• ❌ Tightening the screws. This leads to hinge deformation or thread breakage. Tighten the fasteners with a force of no more than 2–3 Nm (use a torque wrench, if available).
• ❌ Incorrect installation of plugs. If you leave the old holes open, dust and moisture will get in there, which will lead to corrosion.
• ❌ Lack of checking the seal. After rehanging, it must be cleaned of dirt and lubricated, otherwise the door will not be sealed.

Another common problem is extraneous sounds (creaking, knocking) when opening the door. This indicates that the hinges are not level or there is no lubrication. Use food-grade silicone grease (not technical oil!), applying it to the hinge axis.

Models that cannot be hung

Not all refrigerators Indesit support door hanging. Here are signs that your model is not designed for this:

• 🚫 On the opposite side of the case there are no symmetrical holes under the hinges.
• 🚫 There is no section on re-hanging in the instruction manual (check the pages 10–15).
• 🚫 Hinges welded or filled with plastic (relevant for budget models, for example, Indesit ST 167).
• 🚫 Refrigerator built-in — in such models, the doors are attached to the kitchen facade, and rehanging requires dismantling the furniture.

If your refrigerator meets these criteria, but you still need to change the opening side, the solution will be ordering a mirror door from the official dealer IndesitCost - from 5. 000 rubles (depending on the model). An alternative is to use overlay hinges, but this breaks the tightness and leads to increased energy consumption.

How to check for symmetrical ones holes?

Carefully removing the decorative plugs from the opposite side (where you plan to install the hinges), you will see either ready-made holes for screws or blind plastic inserts. In the second case, re-hanging is impossible.

Frequently asked questions after re-hanging

The door closes, but the refrigerator does not. became louder. Is this normal?

Yes, if the sound resembles the hum of a fan (in models with No Frost), the air channel may have shifted when repositioned, and now the fan is working with more load. Check whether the channel is blocked (it should be on the hinge side) - loosen the hinge screws and tighten them again. will eliminate vibration.

The seal does not fit tightly after rehanging. What should I do?

It may have become deformed during dismantling. Try heating it with a hairdryer (temperature 40–50°C) and shape it by hand. If this does not help, the seal needs to be replaced (the article number is indicated in the instructions). 200–1,800 rubles. Before purchasing, measure the length of the door outline.

Is it possible to re-hang the door on an Indesit refrigerator with a display?

Yes, but after re-hanging it may be necessary to reconfigure the electronic unit. In models with a display (for example, Indesit ITF 121 W), the door closing sensor is located on loop, and its position changes. To reset the error, press and hold the button for 10 seconds. If the display shows an error code (for example, 222), contact the service. minutes. If you are doing this for the first time, allow 1.5–2 hours (including adjustment and checking). Do not rush at the stage of removing the hinges - most mistakes occur due to haste. Super Freeze 10 seconds. If the display shows an error code (for example, F04), contact service.

How long does re-weighing take?

For an experienced master - 30–40 minutes. If this is your first time, allow 1.5–2 hours (including adjustment and testing). Take your time during the stitch removal stage - most mistakes occur due to haste.

Do you need to defrost the refrigerator before rehanging?

It is necessary if you have a model with a drip defrosting system. No Frost It is enough to turn off the power for 1-2 hours so that the seal becomes softer. Defrosting is also necessary to avoid water getting on the electronic components when dismantling the doors.

If, after rehanging, the refrigerator begins to freeze worse or condensation appears, check tightness of the seal and position of ventilation ducts. In 90% of cases, the problem is solved by re-adjusting the hinges. For models with Total No Frost (for example, Indesit ITF 120after rehanging, it is recommended to run the function Super Freeze for 2-3 hours - this will help the system stabilize the temperature.