We rehang the door of the Indesit refrigerator yourself: instructions with photos and nuances

Twisting refrigerator doors Indesit is a problem that owners face when moving, renovating a kitchen, or simply wanting to change the opening side. Unlike models from other brands, the equipment of the Italian manufacturer has its own design features: it is important to take into account the location of the freezer (top or bottom), the type of fastenings and even the year of manufacture. For example, refrigerators Indesit until 2018 are often equipped with plastic plugs for self-tapping screws, and in new models - metal bushings.

Many are afraid of damaging the seal or breaking the tightness, but with the right approach the process will take no more than an hour. The main thing is not to skip the step of adjusting the hinges after rehanging, otherwise the door will sag or close poorly. In this article, we will analyze step-by-step instructions, taking into account the nuances for different series Indesit, and also tell you how to avoid typical mistakes that cause you to call a specialist.

It is worth noting that twisting doors does not require special skills, but it will require accuracy. If your refrigerator is under warranty, check the service conditions - some centers Indesit consider independent intervention a reason to refuse repairs. For models with a system No Frost (for example, Indesit DF 4200 W), the process is identical to the classic one, but additional fixation of the defrost sensor cable may be required.

1. Preparation: tools and safety

Before you start work, make sure that the refrigerator unplugged is defrosted. This is not only a matter of safety, but also of practicality: condensation on the seal can interfere with accurate installation. From the tools you will need:

• 🔧 Phillips screwdriver (preferably magnetic so as not to lose the screws)
• 🔨 Hex key 5 or 6 mm (for some models Indesit after 2020 year)
• 📏 Tape measure or ruler (to check gaps)
• 🧲 Magnet or tape (to temporarily fix the door during operation)

Important: in models with electronic display (for example, Indesit ITF 118) before removing the door, disconnect the cable cable going to the control panel. To do this, carefully remove the top cover of the refrigerator - there you will find a connector. If you do not disconnect the cable, you can damage the contacts or break the display mount.

Also prepare the work space: clear the area around the refrigerator (at least 1 m²), lay down soft cloth on the floor - this will protect the door from scratches if it accidentally falls. If the model is heavy (for example Indesit BIAA 13 with a volume of 300+ liters), ask an assistant to hold the door when removing.

⚠️ Attention: In refrigerators Indesit with a system Total No Frost (series ITF i BIAA) after re-hanging the door, it may be necessary to reinstall the air duct. Ignoring this step will result in uneven cooling.

2. Fastening diagram: where and what to unscrew

The design of the hinges depends on the location of the freezer: Indesit depends on the location of the freezer:

• 🔝 Freezer on top (models C 132 G, TLAA 10): the upper hinge is attached to the body of the refrigerator, the lower - to the door. When rehanging, both hinges and plugs are swapped.
• 🔽 Freezer at the bottom (models BIAA 13, DF 5200): the middle hinge (between the refrigerator and freezer compartments) remains in place, only the top and bottom are hung.

All doors Indesit have plastic plugs under the screws - they need to be carefully pryed off with a screwdriver or knife. Under the plugs you will find mounting holes for the alternative opening side. The table below shows standard patterns for popular series:

On the inside of the door (from the seal side) there is usually a sticker with a diagram outweighing. If it is not there, take a photo of the location of the hinges before starting work this will help avoid confusion during reassembly.

3. Step-by-step instructions: remove and install the door

Let's look at the process using the example of a model Indesit C 132 G (freezer on top). For other series, the steps are similar, but the number of loops may differ.

1. Remove the top cover of the refrigerator (if any). It is attached with 2–4 self-tapping screws at the back. Under the lid you will see the top hinge.

2. Unscrew the top hinge (usually 3-4 screws). Hold the door - it is heavier than it seems!

3. Remove the door from the bottom hingeby lifting it up. On some models, you must first remove the pin (use pliers).

4. Move the hinges to the opposite side. There are symmetrical holes for screws on the refrigerator body and door - use them. Don't forget to rearrange plugs to the vacant spaces.

5. Install the door in reverse order: first to the bottom hinge, then fix the top.

For models with freezer from below (for example, Indesit BIAA 13) a step is added to adjust the middle loop: it needs to be loosened, but not completely removed. After rehanging, check that the freezer door opens synchronously with the main one.

All plugs have been removed from the new side|The hinges have been rearranged in a mirror manner|The screws are tightened without distortion|The seal is not twisted-->

What to do if the door does not close after rehanging?

If after installation the door does not fit well, check:

1) Tightening the screws - loose fasteners lead to sagging.

2) Seal - it could move when removing the door. Adjust it around the entire perimeter.

3) Adjusting bolts on the hinges (if any). Rotate them clockwise to raise the door or counterclockwise to lower it.

4. Adjusting the door after rehanging

Even if the door is visually level, it needs to be adjusted. Take a piece of paper and check the tightness:

1. Place the sheet between the seal and the refrigerator body.
2. Close the door and try to pull out the paper.
3. If the sheet comes out without effort, the seal does not fit tightly.

For adjustments:

• 🔩 There is usually a adjusting bolt on the top hinge (for a hexagon). Turning clockwise raises the door, counter-clockwise lowers it.
• 🔧 On the lower hinge, the bolt is responsible for horizontal displacement. Tighten it gradually, checking the gap.

In models Indesit s two-chamber system (for example, DF 5200) may require separate settings for the freezer compartment. To do this, there is an additional screw on the middle hinge - it is adjusted after leveling the main door.

⚠️ Attention: If after adjustment the door still does not close, check magnetic seal. In refrigerators Indesit older than 5 years, it could lose its elasticity. In this case, replacement is required - it is difficult to do it yourself, it is better to contact the service.

5. Typical mistakes and how to avoid them

The experience of craftsmen shows that 70% of problems after re-hanging doors Indesit are associated with three errors:

• 🔌 The display cable is not disconnected (relevant for models with electronic control). This leads to a short circuit or settings failure.
• 🔄 The hinges are not mirrored. For example, the top loop is installed in place of the bottom and vice versa. In this case, the door will be skewed.
• 🧲 Ignoring the magnetic seal. If it is not corrected, the refrigerator will freeze worse and waste more electricity.

Another common problem is loss of screws or plugs. The refrigerator usually comes with spare ones, but if they are not available, use similar ones (length 16–20 mm, diameter 4–5 mm). Do not replace the screws with longer ones - they can damage the internal tubes of the cooling system. Indesit Usually there are spare ones, but if they are not available, use similar ones in size (length 16–20 mm, diameter 4–5 mm). Do not replace the screws with longer ones - they may damage the internal pipes of the cooling system.

In models with ice maker (for example, Indesit WI 161after rehanging, it may be necessary to reconfigure the water supply. To do this:

1. Disconnect the refrigerator from the mains.
2. Remove the back cover of the freezer.
3. Check the position of the water supply tube - it should be on the side of the new loop.

6. Features for Indesit refrigerators with No Frost

In models with a system No Frost (for example, Indesit ITF 118 or DF 5200 S), reversing the door requires additional actions:

• 🌀 Moving the air duct. It is located on the back wall of the refrigerator compartment and is attached to the door. When removing the door, carefully disconnect it, and when installing, fix it on the new side.
• ❄️ Checking the defrost sensor. On some models it is attached to the top loop. If the sensor is not rearranged, the refrigerator will not work correctly.

Also in systems No Frost it is important to monitor tightness of the seal. Due to forced air circulation, even a small gap will lead to freezing of the evaporator and increased load on the compressor.

For models with double cooling system (for example, Indesit BIAA 13 NF) after re-hanging it may be necessary Reset settings. To do this:

1. Turn off the refrigerator for 5 minutes.
2. Turn on and simultaneously press the buttons Super Cool and Super Freeze for 10 seconds.
3. Wait for the sound signal - this means that the settings have been reset.

7. When is it better to call a specialist

Although re-hanging doors Indesit is a feasible task for most users, in some cases it is better to turn to professionals:

• 🔧 If the refrigerator is under warranty, independent intervention can void it.
• ⚡ If the cable is damaged display or system wiring No Frost.
• 🔨 If the door still does not close after several adjustment attempts.

The cost of the service for re-hanging doors in service centers Indesit varies from 1,500 to 3,000 rubles (for 2026). However, if you are confident in your abilities, doing the repair yourself will save both time and money. The main thing is not to rush and follow the instructions.

Remember that in refrigerators with inverter compressor (for example, Indesit ECO 9) calibration may be required after any manipulations with the door. To do this:

1. Turn off the refrigerator for 1 minute.
2. Turn on and set the temperature to +5°C for the refrigerator compartment and -18°C for freezer.
3. Leave it in this mode for 2-3 hours.

⚠️ Attention: The design of refrigerators Indesit may vary depending on the year of manufacture and country of assembly. For example, models produced in Russia (plant in Lipetsk) have plastic hinges, while Italian ones have metal hinges. Check the features of your model in the instruction manual.

FAQ: Frequently asked questions about rehanging Indesit doors

Is it possible to rehang the door of an Indesit refrigerator with a freezer from below without removing the middle hinge?

No, the middle hinge must be loosened, even if it remains in place. This is due to the fact that when the upper and lower hinges are outweighed, the load on the middle fastening changes. If it is not adjusted, the freezer door will sag.

What to do if, after rehanging, the Indesit refrigerator door does not magnetize?

Most likely, the problem is in the seal. Check:

1. Is it twisted when installing the door.
2. Are there any cracks or deformations on it (relevant for refrigerators older than 7 years).
3. Are the hinges adjusted correctly - the door should fit evenly around the entire perimeter.

If The seal is damaged and needs to be replaced. For models Indesit original spare parts with article numbers are suitable C00288356 (for the refrigerator compartment) and C00288357 (for the freezer compartment).

Is it necessary to defrost the Indesit refrigerator before hanging the door?

Yes, defrosting is required for two reasons:

1. Condensation on the seal and hinges can interfere with accurate installation.
2. During operation, the refrigerator will tilt - this can lead to a freon leak if the system is not defrosted.

To speed up defrosting use a fan or leave the door open for 3-4 hours.

How to hang the door on an Indesit refrigerator with a display without breaking it?

The main thing is to carefully disconnect the display power cable. To do this:

1. Remove the top cover of the refrigerator (usually attached to 2 screws at the back).
2. Find the cable connector - it is located next to the top hinge.
3. Carefully press the latch and pull out the cable. Do not pull the wires!

After rehanging the door, connect the cable back and check the functionality of the display. If the screen does not turn on, turn off the refrigerator for 10 minutes - this will reset the error.

How long does it take to rehang the Indesit refrigerator door?

On average, the process takes from 40 minutes to 1.5 hours, depending on the model and experience. Time distribution:

• 🔧 Preparation and defrosting: 20–30 minutes.
• 🔄 Removing/installing the door: 15–25 minutes.
• ⚖️ Adjustment and checking: 10–20 minutes.

If the refrigerator has a system No Frost, add another 15-20 minutes to move the air duct.