Re-hanging the Indesit refrigerator door with your own hands: instructions with photos and videos

Re-hanging the refrigerator door Indesit is a task that almost every owner faces sooner or later. There are different reasons: moving, kitchen renovation, the desire to optimize space, or a simple broken hinge. Fortunately, most models of this brand allow you to change the side of the door opening without calling a technician. But there are nuances: from the location of the freezer to the type of fastening of the hinges, which depend on the specific series of the refrigerator.

In this article we will analyze the process step by step - from preparing tools to the final adjustment of the door. You will learn how to avoid typical mistakes (for example, skew or loose seal), which models require a special approach, and what to do if, after re-hanging, the refrigerator begins to make noise. And also - where to find original plugs for holes and how not to lose the warranty when repairing yourself. Indesit require a special approach, and what to do if, after rehanging, the refrigerator begins to make noise. And also - where to find original plugs for holes and how not to lose the warranty when doing your own repairs.

Spoiler: for most models It will only take 30-60 minutes and a minimum set of tools. But if your refrigerator has a system No Frost or electronic control, be prepared for additional steps. Let's start with preparation!

1. Preparation: Tools and Safety

Before removing the door, make sure you have everything you need. Most tools can be found in the home arsenal, but some parts (for example, plugs for holes) may require purchase.

• 🔧 Screwdrivers: Phillips (usually PH2and flathead (for prying up decorative panels).
• 🔨 Wrench or socket on 10 mm —for hinge bolts (in some models).
• 📏 Ruler or square —to check the evenness of installation.
• 🧲 Magnet or tape — for temporary fastening of removed screws.
• 🧴 Silicone grease (optional)—for processing hinges after installation.

Important: unplug the refrigerator 1-2 hours before the start of work. This is not only safety, but also an opportunity to avoid condensation on the seal. If there is ice in the freezer, let it melt - this will make the door easier to remove.

⚠️ Attention: In models Indesit with an electronic display (for example, series BIAA 13 or CIAO 16) after rehanging may be required reset settings. Take a photo of the current temperature settings and modes in advance.

Also prepare the workspace:

• 📦 Clear the area around the refrigerator (at least 1 m²).
• 🧹 Lay cardboard or fabric - this will protect the floor from scratches if the door falls.
• 👨‍👩‍👧‍👦 Ask an assistant: the refrigerator door weighs 15–30 kg, and it is inconvenient to hold it alone.

2. Re-hanging scheme: general algorithm

The process of re-hanging the door is Indesit standardized, but there are differences depending on type of refrigerator:

General algorithm for most models:

1. Removing decorative covers from hinges (if any).
2. Unscrewing the top hinge (the door is held by an assistant or stop).
3. Removing the door from the bottom hinge (carefully lifting it up).
4. Moving the hinges to the opposite side (using standard holes).
5. Installation of plugs to the old ones holes.
6. Reassembly and adjustment.

In models Indesit with system Total No Frost (for example, Indesit EWT 81052) after re-hanging, you may need to reinstall the air duct between the chambers. Its fastenings are often located under the top hinge.

I photographed the location of the loops and wires (for models with a display)|Disconnected the refrigerator from the network and defrosted it|Prepared plugs for the holes (if not included in the kit)|Checked for the presence of hidden fasteners (for example, under a decorative panel)|Organized an assistant to support the door-->

3. Step-by-step instructions for single-door models

Let's consider the process using the example of a popular model Indesit ITF 118 (single-compartment refrigerator with freezer compartment). unscrew. ITF 108, ITF 120, TS 116.

Step 1: Removing the Hinge Top Cover

Use a flat-head screwdriver to pry up the decorative trim on the top hinge (it is usually plastic and snaps into place). Below it you will see mounting bolts. In some models, the cover may be metal - it needs to be unscrewed.

Step 2. Unscrewing the top hinge

Use a Phillips screwdriver to unscrew 2-3 bolts (usually hold the door, as after removing the last bolt it may fall. If the bolts do not give way, spray them. PH2). Hold the door as it may fall after removing the last bolt. If the bolts do not budge, spray them WD-40 and wait 5-10 minutes.

Step 3. Removing the door from the lower hinge

Lift the door up 1-2 cm - it should come out of the grooves of the lower hinge. If the door is “jammed”, check if the seal or ice in the freezer is in the way. c No Frost sometimes you need to slightly lift the refrigerator by the front leg to relieve the pressure.

Step 4. Transferring the hinges

On the opposite side of the case you will see symmetrical holes for the hinges (they can be closed with plugs) Rearrange the hinges in a mirror-like manner, using the same ones. bolts. Do not overtighten the fasteners —this can deform the door.

Step 5. Installing plugs

Plastic plugs for old holes are usually included with the refrigerator. If they are not available, you can buy universal ones (diameter. 8–10 mm) in a furniture fittings store. The plugs are inserted from the front side of the refrigerator.

Step 6. Reassembly

Place the door on the lower hinge, then fix the upper one. Check that the door opens smoothly and does not touch the body. If there is a distortion, loosen the bolts and adjust the position.

What to do if the door does not close tightly after installation?

If the seal does not fit evenly, the reasons may be the following:

1. Distortion of the hinges — loosen the bolts and level the door.

2. Deformation of the seal — warm it up with a hairdryer (temperature 50–60°C) and shape it with your hands.

3. The magnets get in the way —in some models Indesit seal magnets may “stick” to the body. Lubricate them with a thin layer of silicone grease.

4. Incorrect installation of plugs —if they protrude, the door will not fit tightly. Sharpen them with sandpaper.

4. Nuances for two-door refrigerators

Two-door models Indesit (for example, BIAA 13, CIAO 16, TIA 11) require re-hanging both doors —first the main chamber, then the freezer. The main difficulty is middle hingewhich is attached to the partition between the chambers.

Features for the freezer from below (BIAA 13):

• 🔹 Upper The freezer hinge is attached to middle partition —it needs to be unscrewed first.
• 🔹 The lower hinge of the main chamber can be blocked by the compressor mount. You will have to unscrew its bolts (usually 2 pieces at the back).
• 🔹 After rehanging, check if it is in the way air duct between the chambers (in models with No Frost).

Features for the freezer on top (TIA 16):

• 🔹 Bottom hinge of the main chamber often has an additional lock —it needs to be pressed out with a screwdriver.
• 🔹 The upper door (freezer) is lighter than the bottom, but its hinges can be hidden under the decorative panel.
• 🔹 In some models after rehanging, it is required to reconfigure the door opening sensor (it can be integrated into the hinge).

For models Side-by-Side (SIAES 16) the process is even more complicated:

• 🔹 The hinges are hidden under decorative linings on the sides of the doors.
• 🔹 The doors are very heavy (up to 30 kg each) - an assistant is definitely needed.
• 🔹 After re-hanging, it may be necessary calibration of the electronic unit (if the refrigerator has a display).

⚠️ Attention: In models with electronic control (for example, Indesit EWT 81052) after re-hanging the door, an error may light up E01 or E02. This means that the door position sensor does not work. Solution: turn off the refrigerator for 5 minutes, then turn it on again. If the error remains, check the sensor connector (it may be pinched by the loop).

5. Adjusting the door after re-hanging

Even if you did everything correctly, the door may does not close tightly. data-i="205">creak, creak or open on its ownThis can be solved by adjusting the hinges and seal.

Problem 1: The door does not close tightly

• 🔧 Check refrigerator level - if it is not level, the door will be skewed. level.
• 🔧 Loosen the bolts on the hinges and slightly move the door in the desired direction.
• 🔧 Check the seal: if it is deformed, warm it with a hairdryer (temperature no higher than 60°C) and tighten shape.

Problem 2: The door creaks when opening

• 🛢️ Lubricate the hinges silicone lubricant (do not use WD-40 or oil - they attract dust).
• 🔧 Check whether the door is touching the body. If so, loosen the hinges and adjust the position.

Problem 3: The door opens spontaneously

• 🧲 Check the magnets of the seal - they may weaken over time. Try to remagnetize them by rubbing. magnet on the seal.
• 📉 Increase the tilt angle of the refrigerator back (adjust the front legs). The door should close under its own weight.

For fine adjustment, use hex wrench (usually 4 mm or 5 mm), which comes with the refrigerator. Rotate the bolts on the hinges clockwise to raise the door, or counterclockwise to lower it.

6. Typical mistakes and how to avoid them

Even experienced craftsmen sometimes make mistakes when rehanging doors Indesit. Here are the most common:

• 🚫 Ignoring stubs - open holes spoil the appearance and collect dust!
• 🚫 Tightening the bolts - this will deform the hinges and the door. Tighten all the way, but without fanaticism.
• 🚫 Incorrect procedure - for example, remove the bottom hinge first, not the top!
• 🚫 Loss of screws or plugs - store them in a magnetic container or bag.
• 🚫 Ignoring electronic sensors - in models with a display this can lead to errors.

Another common problem is damage to the seal. If you accidentally tear it with a screwdriver, do not try to seal it with tape! Better order a new seal (the article number is usually indicated in the instructions or on the seal itself). For models Indesit universal seals are suitable. marks Sibir or RubberMag.

If after rehanging the refrigerator becomes more noisecheck:

• 🔊 Does the door touch the housing when the compressor is operating (vibration may increase).
• 🔊 Are the compressor fastenings loose (sometimes they have to be tightened after removing the door).
• 🔊 Has debris gotten into the fan (in models with No Frost).

⚠️ Attention: B refrigerators Indesit with a system Total No Frost (for example, EWT 81052) after re-hanging, air circulation may be disrupted. If after a day the freezer becomes less freezing, check whether the air duct between the chambers is pinched. It should be smooth and not deformed.

7. Where to find parts and accessories

If you are missing plugs, screws or seals, you can buy them in addition:

• 🛒 Official service centers Indesit - original parts, but more expensive.
• 🛒 Online stores (for example, "Spare parts for household appliances", "220-volt.ru") - a wide range, but check compatibility by model.
• 🛒 Furniture fittings stores - universal plugs and screws.
• 🛒 Used markets (Avito, Yula) - sometimes they sell kits for re-hanging from disassembled refrigerators.

When purchasing, pay attention to:

• 🔹 Diameter of holes for plugs (usually 8–10 mm).
• 🔹 Length of screws - too long can damage the inner lining.
• 🔹 Sealant material - for Indesit rubber or silicone with a magnetic insert is suitable.

Cost of parts (for 2026):

• 💰 Set of plugs (4 pcs.) - 150–300 rubles.
• 💰 Seal (according to door perimeter) - 800–1500 rubles.
• 💰 Screws and hinges (if lost) - 200–500 rubles per set.

If you are not sure about the choice, take an old part with you or take a photo of it with a ruler for scale.

8. When is it better to call a specialist

Although re-hanging a door Indesit usually does not require professional skills, there are cases when it is better to contact the service:

• 🔧 The refrigerator is under warranty - self-repair can void it.
• 🔧 Models with electronic control (for example, Indesit EWT 81052), if after re-hanging errors appeared on the display.
• 🔧 Side-by-Side - due to the weight of the doors and the complexity of the fastenings.
• 🔧 If the doors are damaged during removal refrigerant pipes (this is dangerous!).
• 🔧 If after all the manipulations the door does not close or refrigerator does not freeze.

Cost of re-hanging the door in the service (for 2026):

• 💰 Single-door refrigerator - 1500–2500 rubles.
• 💰 Two-door - 2500–4000 rubles.
• 💰 Side-by-Side - 4000–6000 rubles.

If you decide to do it yourself, but something went wrong, don’t panic. Most mistakes are correctable. installation does not close, check:

1. Is the refrigerator level (use a level).
2. Is the seal in the way (sometimes it needs to be trimmed slightly).
3. Are the hinges tightened correctly (loosen and tighten again).

FAQ: Frequently asked questions

Is it possible to re-hung the Indesit refrigerator door without an assistant?

Technically yes, but it's dangerous. The refrigerator door weighs 15–30 kg and is difficult to hold alone. If there is no assistant, use supports (for example, a chair or box) or belt slings to fix the door in the raised position. In models Side-by-Side you can’t do without an assistant.

What to do if after re-hanging the door does not close tightly?

There are several reasons:

1. Distortion of the hinges — loosen the bolts and adjust the position of the door according to the level.
2. Deformation of the seal —heat it with a hairdryer (50–60°C) and shape it.
3. The magnets are in the way — lubricate them with silicone grease.
4. Uneven floor —adjust the legs of the refrigerator.

If all else fails, check to see if the door itself is bent (this happens when you fall).

Is it necessary to defrost the refrigerator before rehanging?

It is advisable, but not necessary. If there is a lot of ice in the freezer, it may interfere with the door's removal. It is enough to turn off the refrigerator 1–2 hours before work so that the ice melts slightly. In models with No Frost there is no need to defrost.

Where can I get plugs for the holes if they are lost?

Plugs can be:

• Buy at Indesit service center (original).
• Pick up universal at a furniture fittings store (diameter 8–10 mm).
• Order at AliExpress or Wildberries (search for "refrigerator plugs").
• Make it yourself from plastic plugs or rubber shock absorbers.

Select a color to match the refrigerator (usually white, gray or black).

Will re-hanging the door affect the warranty?

Formally re-hanging yourself is not a warranty case, but if you damage the hinges, seal or electronic components, the service center may refuse warranty repairs. To avoid problems:

• Take a photo of the process (in case of disputes).
• Do not use force when unscrewing the bolts.
• If the refrigerator is electronically controlled, after re-hanging, reset settings.

In most cases, the warranty is maintained if re-hanging is done carefully.