How to hang the Indesit refrigerator door to the other side: video instructions and step-by-step instructions guide

Repositioning the door refrigerator Indesit to the opposite side is a task that many owners face when moving, renovating a kitchen, or simply wanting to optimize space. Despite the apparent complexity, the procedure is quite doable with your own hands if you know the key nuances of the design and avoid typical mistakes. In this article we will analyze not only the universal algorithm of actions, but also features of Indesit modelswhere door fastenings may differ from standard ones.

You will find here step-by-step instructions with photographs, hidden "pitfalls" of the process (for example, why the door may not close well after rehanging)as well as a selection of video tutorials from the masters. We will pay special attention to the tools - without the correct set of keys and screwdrivers, the risk of damaging the hinges or seal increases significantly. If your refrigerator Indesit model C 132 G, B 16 FNF or another popular series, the instructions are suitable with minimal adjustments.

Preparation for rehanging: tools and safety

Before you begin dismantling, make sure you have on hand:

• 🔧 Phillips and flathead screwdrivers (for screws of different types)
• 🔨 Wrenches (usually 8, 10 and 13 mm - depends on the model)
• 🧲 Magnet or bowl for small parts (screws, washers, plugs)
• 📏 Level (to check the evenness of installation after rehanging)
• 🧴 Silicone grease (for hinges, if they creak)

Important: Indesit in some models it is used left-side threaded connections on hinges. This means that you need to unscrew the screws clockwise, and not against it, as usual. Neglecting this rule can lead to thread failure. Also check whether the refrigerator is included plugs for holes - they need to be moved to the opposite side of the case.

⚠️ Attention: If your refrigerator Indesit with system No Frost, before hanging the door be sure to unplug it for 10-12 hours. This is necessary to completely defrost the ice in the air ducts - otherwise, when the housing is tilted, water may get into the electronic unit.

Step 1: Removing the top door hinge

Start from the top hinge - it is usually easier to disassemble. Algorithm of actions:

1. Open the refrigerator door 90 degrees and support it a wooden block or book (so that it does not fall when unscrewing).
2. Remove decorative cover hinges (it snaps or is secured with one screw).
3. Unscrew top mounting screw hinges to the refrigerator body (usually it is hidden under the lid).
4. Hold the door, carefully remove it from the top pin and place it on the floor, having previously laid a soft cloth.

In models Indesit s double door (freezer + refrigerator) the upper part is dismantled first, and then the lower part. If the hinge is “stuck” and does not give in, do not apply force - process the connection WD-40 and wait 10 minutes.

Step 2: Transferring the lower hinge and fastenings

The lower hinge is most often fixed two screws: one fastens it to the body, the second to the door. It is important here:

• 🔄 Move opening limiter (if there is one) to the opposite side.
• 🔧 Unscrew screws holding the hinge on the body, and rearrange it into the mirror holes.
• 🔍 Check if there are any left in the old holes plastic bushings or washers —they also need to be moved.

In refrigerators Indesit series BIAA 13 the lower hinge may have hidden lockwhich holds the door closed. It must be carefully removed with a flat screwdriver so as not to damage the plastic case.

Step 3: Rearranging the handle and seal

The door handle is attached to two screwshidden under the decorative trim. To remove it:

1. Pry the cover with a flat screwdriver from the side (usually there is a small gap there).
2. Unscrew the screws and remove the handle.
3. Move it to the opposite one side mirrored (the holes are already provided by the manufacturer).

The sealing rubber (magnetic circuit) in refrigerators Indesit is symmetrical, so there is no need to rearrange it. However, after installing the door, check that the seal fits tightly along the entire perimeter. If there are gaps, heat the rubber with a hairdryer (temperature 50–60°C) and shape it with your hands.

Step 4: Installing the door on the new side

Now assemble the structure in the reverse order:

1. Put the door on bottom pin hinges (hold it so that it does not fall).
2. Align the upper part and secure it with a screw. Do not tighten it all the way —first check if the door opens easily.
3. Adjust the door position using adjusting screws on hinges (they allow you to move the door up and down and left and right).

After preliminary fixation:

• 📏 Check levelif the refrigerator is level. If necessary, adjust the legs.
• 🧲 Make sure that magnetic seal is attracted evenly on all sides.
• 🔄 Open and close the door 5–6 times - if she opens spontaneously, you need to tighten the hinges more or adjust the limiter.

What to do if the door creaks after rehanging?

The creaking occurs due to a lack of lubrication in the hinges or their misalignment. Treat the hinges with silicone grease (do not use petroleum-based oils - they damage the plastic). If the creaking remains, check whether the door touches the body when opening (you may need to loosen the fastenings and move it by 1-2 mm).

Typical mistakes and how to avoid them

Even with careful installation, mistakes can be made that will lead to loose closing, distortion or breakage of hinges. Let's look at the most common ones:

⚠️ Attention: If after rehanging the refrigerator Indesit started more noise, check whether the compressor tube is touching the door housing. In some models (for example, Indesit EWT 167), when changing the opening side, it is required reconfiguration of shock absorbers.

• 🚫 Incorrect tightening of the screws - if you overtighten, the hinge will be deformed; if you don’t tighten it enough, the door will “walk.”
• 🔄 Ignoring the plugs - open holes spoil the appearance and collect dust.
• 🧲 Damage to the seal - even a small tear in the elastic will lead to loss cold.
• ⚡ Operation under voltage —in models with an electronic display (Indesit ITF 118) this can cause a malfunction in the control unit.

If the door is after overweight does not close tightly, try:

1. Loosen the top hinge and move the door towards the body by 1-2 mm.
2. Warm the seal with a hairdryer (as described above).
3. Check whether the vegetable drawer shelves are in the way - sometimes they move when the refrigerator is tilted.

Video instructions: selection of the best videos

For clarity, we recommend watching videos from the masters. We have selected videos that show the nuances specifically for refrigerators Indesit:

• 🎥 "Rehanging the Indesit C 132 G door in 10 minutes" —a step-by-step analysis with comments on the tools.
• 🎥 "Secrets of Indesit hinges: left-hand thread and hidden fasteners" —emphasis on non-obvious points.
• 🎥 "What to do if the door does not close after rehanging?" —diagnosis and solutions to problems.

Pay attention to the comments under the video - there are often are discussed specific models and advice is given on their features. For example, Indesit BIA 18 may require moving the closing sensorwhich is not always mentioned in the instructions.

FAQ: Frequently asked questions about hanging the Indesit door

Is it possible to hang the Indesit refrigerator door without an assistant?

Technically yes, but it is risky. The door weighs 10–15 kg, and without support it is easy to drop it, damaging the hinges or the frame. If you don't have a helper, use strong ropesto hang the door from a ceiling beam or cabinet while dismantling. In models with French Door (double doors) help is required!

Do you need to defrost the refrigerator before rehanging?

For models with No Frost — It is necessary (turn off for 10–12 hours). For drip systems, it is enough to remove food to let the refrigerator stand for 1-2 hours with the door open for the condensation to evaporate. This will prevent moisture from entering the electronic components when the case is tilted.

What to do if the door sags after rehanging?

Sagging occurs due to:

1. Loose hinges —tighten the screws (but do not overdo it).
2. Worn pin in the bottom hinge—the part needs to be replaced.
3. Case misalignment —adjust the legs of the refrigerator according level.

If the sagging remains, check whether the inside of the hinge is cracked (a common problem in models plastic sleeve inside the loop (a common problem in models Indesit over 5 years old).

Is this instruction suitable for Indesit refrigerators with a display?

In general, yes, but in models with electronic control (Indesit EWT 269, ITF 118) there are nuances:

• Before work turn off the power and wait until the display turns off completely (1-2 minutes).
• Do not touch sensor wires (they may be attached to the door).
• After rehanging, it may required reset settings (hold the button Super Cool 5 seconds).

Where can I find spare hinges for Indesit if the old ones are broken?

Original hinges can be order:

• On the website Indesit (section "Spare parts").
• In service centers - check serial number of the refrigerator (located on the sticker inside the chamber).
• On AliExpress or eBay —look for the part code (for example, C00304306 for the top loop Indesit C 132 G).

The cost of the original loop is from 800 to 2500 rubles. Analogues cheaper, but may not fit in size or thread.