Reversing the LG refrigerator door to the other side: video instructions and lifehacks

Rearranging the refrigerator door LG to the opposite side is a task that many owners face when moving, renovating a kitchen, or simply wanting to optimize space. Despite the apparent complexity, the procedure is quite doable with your own hands if you know the key nuances: from the correct dismantling of hinges to the transfer of electrical wiring (for models with a dispenser). In this article you will find a step-by-step guide with videoan analysis of typical errors and a table of tool compatibility for different series LG.

Important: the design of refrigerator doors LG varies depending on the year of manufacture and functionality. For example, models with a system Door-in-Door or a built-in ice maker require a special approach. We took these features into account and prepared universal instructions that are suitable for 90% of the brand’s household refrigerators. If your model belongs to the premium series (for example LG Instaview or Signature), check for additional fasteners before starting work.

Before you begin, answer one question:

Preparation: tools and safety

For hanging the refrigerator door LG You will need a minimum set of tools, but their absence may lead to damage to the case or hinges. Here is the complete checklist:

Pay special attention hex wrench — in 70% of models LG (for example, series GA-B or GC-X) hinges are fastened with star or hex bolts. Using the wrong tool (for example, a flathead screwdriver) will cause the edges of the bolt to “lick off.” If your kit does not have a hex key, purchase it in advance - the cost is 50–150 rubles.

Before starting work:

• 🔌 Unplug the refrigerator and wait until the interior lighting goes out (this will take 1–2 minutes). Some models LG have capacitors that retain charge even after being turned off.
• 🧊 Defreeze the refrigeratorif it is not equipped with a system No Frost. This will prevent moisture from entering the electrical contacts during dismantling.
• 📦 Release the door shelves from food and remove them. The shelves are usually attached to plastic clips - pull them up with force.

Step 1: Removing the top hinge

Start with the top hinge - it is usually easier to handle than the bottom. Algorithm of actions:

1. Remove the decorative plug of the loop (it is secured with latches). Use a flat-head screwdriver to pry it off from the side, where there are no visible fasteners.
2. Under the plug you will see 2-3 bolts. In models LG before 2020, bolts are often used for a Phillips screwdriver, in new ones - for a hexagon. Do not unscrew the bolts completely - it is enough to loosen them by 2-3 turns.
3. While holding the door (it heavier than it seems!), carefully remove it from the top pin of the hinge and place it on the floor, first placing a soft cloth.

The main thing in this step is not to mix up the bolts. In refrigerators LG the upper and lower hinges often have bolts of different lengths. To avoid confusion, fold them separately or mark them with tape.

What to do if the bolt cannot be unscrewed?

If the bolt is “stuck” or the edges are licked off, use WD-40 or an equivalent. Apply the product, wait 10 minutes and try again. If that doesn’t help, carefully drill out the bolt with a drill with a thin drill (2–3 mm), then remove the remains with pliers.

Step 2: Transferring the bottom hinge and preparing the holes

The bottom hinge is the most critical step. There are often hidden pitfalls here:

• 🔧 In models with a dispenser (LG GR-B207, GC-B247 etc.), water supply hoses pass under the lower loop. They need to be carefully disconnected, after being pinched with pliers to avoid leaks.
• 🔄 On the opposite side of the refrigerator body LG usually there are already technological holes for the hinges, closed with plugs. If there are no holes, you will have to drill them yourself (see the table below).
• ⚡ For models with an electronic display (series Instaview) before removing the hinge, turn off the door power cable. It is located under the decorative panel and is fixed with a plastic clip.

Location and diameter of holes for hinges in refrigerators LG (standard models):

In LG refrigerators with the Door-in-Door system (for example, model GC-B247) the bottom hinge has an additional lock that holds the inner door. It must be removed first, otherwise the hinge will not detach.

Step 3: Transferring electrical wiring and hoses (for models with a dispenser)

If your refrigerator is equipped with a water or ice dispenser, you will have to move the hoses and wires to the other side. Here's how to do it correctly:

1. Disconnect the water supply hose from the back of the refrigerator. It is usually secured with a plastic nut - unscrew it counterclockwise.
2. Pull the hose through the body of the refrigerator. Models LG have special channels for this (look for rubber seals on the side).
3. Connect the hose to the new location, making sure that it is not kinked. Check the tightness of the connection by turning on the water supply for 10–15 seconds.
4. For electrical wiring (if there is a display on the door), use the cable duct that comes with the refrigerator. If it is not there, secure the wires with electrical tape, avoiding tension.

⚠️ Attention: In refrigerators LG with the function Smart ThinQ (for example, models LRMVC2306S) a Wi-Fi module is installed in the door. When transferring the wiring, do not pull the antenna cable - it is fragile and can come off the board.

After transferring the wiring and hoses, check:

• 💧 There are no water leaks when the dispenser is turned on.
• 🔋 Does the backlight and display on the door work (if any).
• 📶 Is the Wi-Fi connection still intact (for “smart” models).

Step 4: Installing the door on the new side

Now you can begin reassembling. Follow this order:

1. Install the bottom hinge onto the new side by inserting the pin into the hole. Tighten the bolts not all the way —the door should “play” a little for adjustment.
2. Place the door on the lower pin and align the upper hinge. An assistant will be needed here, since the door needs to be held level.
3. Tighten the bolts of the upper hinge, then finally secure the lower one. Use torque wrench (if any) with a force of 1.5–2 Nm for M6 bolts.
4. Install decorative plugs and check the door movement. It should open smoothly, without creaks or distortions.

If the door LG after installation does not close well or opens spontaneously, the reasons may be the following:

Step 5: Adjusting and checking the tightness

The final stage is adjusting the door for a perfect fit. Here's what you need to do:

1. Checking the level: Use a spirit level to make sure the door is level. If necessary, adjust the height of the refrigerator legs.
2. Leak test: Close the door and try to stretch a sheet of paper around the perimeter of the seal. If the sheet passes easily, the seal needs adjustment.
3. Sealant adjustment: In models LG the seal is attached to a magnetic tape. If it comes off, warm the problem areas with a hairdryer (temperature 50–60°C) and press with your hands.

For models with Door-in-Door (inner door) additionally check:

• 🔄 Smooth movement of the inner door - it should not cling to the main one.
• 🧲 Strength of magnets - if the inner door opens with a light touch, the magnetic tape needs to be replaced.

⚠️ Attention: In refrigerators LG with function Smart Diagnosis (for example, LRMVC2306S) after re-hanging the door, an error may occur dH (door malfunction). To reset it, press and hold the button Ice Plus for 5 seconds.

Video instructions: rehanging the LG refrigerator door

For clarity, we have prepared a selection of videos with a step-by-step process. Pay attention to models similar to yours:

• 📺 Without dispenser: Video for models GA-B, GC-X (duration 8:45).
• 📺 With dispenser: Video for GR-B, GSL (with hose transfer) (duration 12:20).
• 📺 Side-by-Side: Video for GSL361, GSL761 (duration 15:10).

If the video uses tools different from yours, do not be alarmed - the principle of operation is the same. The main thing is to follow:

• 🔧 The sequence of removing the hinges (from top to bottom).
• 🔌 Correct disconnection of the wiring (if any).
• 📏 The accuracy of marking new holes.

In refrigerators LG Instaview series (for example, model LRMVC2306S) after reversing the door, the touch panel may need to be reprogrammed. To do this, hold down the "Lighting" and "Ice Type" buttons for 10 seconds.

Typical mistakes and how to avoid them

Even when following the instructions, many make mistakes that lead to breakdowns. Here are the most common ones:

1. Using inappropriate tools. For example, trying to unscrew hex bolts with a Phillips screwdriver results in the edges being licked off. Solution: Buy tools in advance, checking the table above.
2. Incorrect transfer of hoses. In models with a dispenser, the hoses must not be bent or pulled too hard. Solution: Use standard channels in the refrigerator body.
3. Tightening the bolts. This deforms the hinges and leads to the door being skewed. Solution: Tighten the bolts with a force of no more than 2 Nm.
4. Ignoring the tightness check. Poor fit seal increases energy consumption by 15–20%. Solution: Check the tightness with a sheet of paper.

If after rehanging the door LG it has become worse to close, use this algorithm:

⚠️ Attention: In refrigerators LG with a system Linear Cooling (for example, models GC-B247) after reversing the door, cooling may temporarily deteriorate. This is due to the redistribution of cold air. Give the refrigerator 12–24 hours to stabilize the temperature.

FAQ: Frequently asked questions about re-hanging the LG door

Is it possible to re-hang the LG refrigerator door yourself if you have no experience?

Yes, the procedure is not required special skills, but it is important to follow instructions and use the right tools. Start by watching a video for your model to get an idea of ​​the scope of work. If the refrigerator is under warranty, it is better to contact a service center - independent intervention may void the warranty.

How long does it take to rehang the door?

On average, the process takes 1-2 hours for models without a dispenser and 2-3 hours for refrigerators with an ice maker. Most of the time is spent on transferring hoses and wiring. If this is your first time doing this, allow 3-4 hours, including breaks.

Do you need to defrost the refrigerator before hanging the door?

It is mandatory if your model is not equipped with a system No Frost. Otherwise, condensation may get onto the electrical contacts during dismantling. To No Frost it is enough to unplug the refrigerator for 30 minutes before starting work.

What to do if, after rehanging, the door does not close tightly?

There may be several reasons:

• Hinges are skewed - loosen the bolts and adjust the position of the door according level.
• Deformation of the seal - warm it with a hairdryer (50–60°C) and press.
• Incorrect tilt angle of the refrigerator - adjust the front leg so that the door is at an angle of 1-2° back.

If the problem is not solved, check if there is any interference shelves or drawers inside the refrigerator.

Is it possible to reverse the door on an LG Side-by-Side refrigerator?

Yes, but the process is more complicated than with classic models. T Side-by-Side the two doors are connected by a common hinge, and they have to be hung at the same time. In addition, the doors weigh more (up to 25 kg each), so you can’t do it without an assistant. For models LG GSL361 i GSL761 we recommend using special ties to secure the doors during work.