Rehanging the refrigerator door “Biryusa” on the other side: step-by-step video and instructions for beginners

Rearranging the refrigerator door Biryusa to the opposite side is a task that many owners face when moving, renovating, or the banal need to optimize space in the kitchen. Despite the apparent complexity, the procedure is quite doable at home without calling a specialist, if you strictly follow the algorithm and take into account the nuances of a particular model. The main thing is to take your time, prepare the tools and remember the key points: from the correct removal of decorative plugs to fine adjustment of the hinges after installation.

In this article you will find step-by-step guide with videoadapted for popular models Biryusa (for example, Biryusa-10K, Biryusa-18C etc.), as well as list of necessary tools, typical mistakes and tips for avoiding breakdowns. We will pay special attention adjusting the door after rehanging - this stage is often missed, which is why, over time, a distortion or loose fit of the seal appears.

If your refrigerator was manufactured after 2010, most likely the design of the hinges is unified, and the instructions will work with minimal adjustments. For older models (before 2005), additional parts may be required - we’ll tell you about this too.

Preparation: tools and safety measures

Before you start work, make sure that you have everything you need on hand. Minimum set of tools to hang the door Biryusa:

• 🔧 Phillips screwdriver (PH2 is usually suitable) - for unscrewing hinges and fasteners.
• 🔧 5 mm hexagon (for some models where the hinges are fixed with hexagon socket bolts).
• 🔧 Flat screwdriver or plastic spatula — for removing decorative plugs.
• 📦 Painting tape —to fix the door in the open position and avoid falling.
• 🧲 Magnet or pallet - for collecting small parts (screws, washers).

Also prepare clean cloth or a towel - you can put the removed door on them so as not to scratch the surface. If the refrigerator No Frostbefore operation, unplug it for 10-15 minutes so that the fan stops. For models with a drip defrosting system, simply remove the food and shelves from the door compartments.

⚠️ Attention: Do not turn the door upside down after removal - this may damage sealing rubber or the shelf mounting system. Place it on a flat surface with a soft cloth.

If your refrigerator Biryusa is equipped display or electronic control unit on the door, before starting work, take a photo of the location wires and connectors. In most cases, they do not need to be disconnected - just carefully move the door along with the wires, but for models with touch control (for example, Biryusa-22S), partial disassembly of the panel may be required.

Step 1: Removing the decorative plugs and top hinge

Start with top hinge —it is usually easier to dismantle. Gently pry decorative cap a flathead screwdriver or plastic spatula. On most models Biryusa the cap is held on by latches, but in some series (for example, Biryusa Premium) it can be screwed on from the bottom.

After removing the plug you will see fastening bolts loops. Their number depends on the model:

• 🔹 2 bolts —for refrigerators up to 160 cm high (for example, Biryusa-10K).
• 🔹 3 bolts —for models from 170 cm (for example Biryusa-18S).
• 🔹 4 bolts - for two-chamber refrigerators with increased load on the hinges.

Unscrew bolts cross. with a screwdriver, holding the door with your hand. Do not remove the hinge completely - just loosen the fastening so that the door can be lifted and removed from the lower pin. If the bolts are stuck, use WD-40 or an equivalent, but avoid getting liquid on the seal.

⚠️ Attention: On some models Biryusa (for example, Biryusa-22S) the top hinge is hidden locking screw under the decorative trim. If the door cannot be removed after unscrewing the visible bolts, check for the presence of additional fasteners!

After loosening the top hinge, carefully lift the door up to remove it from the lower pin. If the door is heavy (for example, on two-chamber models), ask an assistant to hold it. Place the door on the prepared surface do not place it on its side. data-i="136">☑️ Preparing to remove the door - this may deform the seal.

Step 2: Removing the bottom hinge and rearranging the fasteners

Bottom hinge on refrigerators Biryusa usually is fixed two bolts and has pin-axison which the door is held. After removing the door, unscrew the bolts and remove the hinge. Pay attention to plastic washers or gaskets —they must be saved and installed in a mirror during assembly.

On the opposite side of the body (where the door will be moved) you will see plugs for fasteningsThey need to be removed by prying them under with a screwdriver. there are plugs threaded holes for the hinges - they can be closed with factory plugs. Remove the plugs, if any.

Important point: on some models Biryusa (for example, Biryusa-130) holes for the hinges not symmetrical. In this case, you will need rearrange metal bushings (they are screwed into the body) to the other side. hexagon 5 mm to dismantle them.

After rearranging the bushings or plugs check the compatibility of the holes with hinges. If the holes do not line up, you may need expand them with a drill (use a 4-5mm drill bit). However, on most modern models Turk the holes are universal, and additional modification is not needed.

Step 3: Transferring the handle and seal (if necessary)

On most models Biryusa door handle it is universal and does not require transfer - it can simply be turned over or moved to the other side without additional tools. However, in some series (for example Biryusa-130) the handle is secured with screws and needs to be removed:

1. Unscrew screws for securing the handle (usually 2-3 pieces).
2. Remove the handle and move it to the opposite side, turning it mirrored.
3. Tighten the screws without overtightening - a tight fit is enough.

As for sealing gum, on refrigerators Turk it is usually does not require transfer - just install the door correctly, and the elastic band will automatically take the desired position. However, if the seal is deformed or torn, it is better to replace it before rehanging the door. To do this:

• 🔧 Carefully pry the seal around the perimeter of the door (it is held in the groove).
• 🔧 Remove the old rubber band and clean the groove from glue or dirt.
• 🔧 Install a new seal, starting from the corners, and warm it hairdryer for a better fit.

If the seal is in good condition, but after rehanging the door poor fitthe cause may be incorrect adjustment of hinges or the body is skewed. We will talk about this in the next section.

What to do if the seal comes off after rehanging?

If the sealing rubber does not fit well after installing the door, check:

1. Correct adjustment of the hinges (the door should close with light force).

2. Integrity of the magnetic insert inside the seal (if damaged, replacement is required).

3. Cleanliness of the groove - sometimes dirt or remnants of old glue accumulate there.

If the problem remains, warm the seal with a hairdryer (temperature 50–60°C) and press the door for 10–15 minutes.

Step 4: Installing the door on the new side and adjusting

Now we move on to the most important part installing the door on the opposite side. Follow the algorithm:

1. Bring the door to the refrigerator and align bottom pin with the hole in the hinge.
2. Lower the door down so that the pin entered the groove. Hold the door so that it does not fall.
3. Install top hinge and tighten the bolts not up to end (70–80% of the effort).
4. Check how the door closes. If there is misalignment, loosen the bolts and adjust the position.

For adjustments doors, use the following method:

• 🔧 If the door touches the body from below — lift it up slightly and tighten the bottom hinge.
• 🔧 If the door does not fit tightly on top — loosen the top hinge and slide the door down.
• 🔧 If the door opens on its own check the horizontal level (the refrigerator may be on a slope).

Critical point: after adjustment, tighten the hinge bolts crosswise to avoid distortion. For example, first the upper left bolt, then the lower right, then the upper right and lower left. This will ensure uniform distribution load.

After final fixation of the hinges, check tightness of the seal. To do this, use test with a paper sheet:

1. Insert a sheet of paper between the seal and the body.
2. Close the door and try to pull out the sheet.
3. If the sheet pulls out effortlessly the seal requires adjustment or replacement.

Step 5: Checking operation and eliminating possible problems

After installing the door be sure to check:

• 🔹 Make sure that door opens and closes smoothly, without creaks.
• 🔹 Check the gap between the door and the body —it should be the same around the entire perimeter.
• 🔹 Turn on the refrigerator and make sure that the compressor starts (there are no errors on the display, if any).
• 🔹 After 1-2 hours, check whether condensation on the seal is a sign of a leaky fit.

If problems arise after rehanging, here are the reasons and solutions:

If your refrigerator Biryusa equipped open door alarm system, after reweighing it may be required error reset. To do this:

1. Disconnect the refrigerator from the network for 5 minutes.
2. Plug it back in and wait initialization.
3. If the signal remains, check sensor contacts (they can be on the hinge or body).

⚠️ Attention: On models Turk s electronically controlled (for example, Biryusa-22S) after re-hanging the door may be required sensor calibration. This is usually done automatically, but if an error appears on the display (for example E1 or E2), refer to the operating instructions.

Video instructions and additional tips

For clarity, we recommend that you read video instructions on rehanging the refrigerator door Biryusa. The video below shows the process on the model Biryusa-18S, but the algorithm is also suitable for other series with minimal adjustments:

Key points from the video:

• 🎥 How to properly remove decorative plugs without damage.
• 🎥 The sequence of unscrewing the hinge bolts (from top to bottom).
• 🎥 Adjusting the door using level (optional).
• 🎥 Checking the seal after installation.

If you have not found a video specifically for your model, pay attention to general principles:

• 🔹 Hinges on refrigerators Biryusa usually universal, so the rehanging process is similar.
• 🔹 The main difference is number of bolts and the presence of bushings (see table above).
• 🔹 For models with display it is important not to damage the wires when rearranging.

If you are afraid of damaging the refrigerator, try first practice on the top hinge - its dismantling is less critical than the lower one. You can also take a photo of each stageso as not to confuse the parts during assembly.

FAQ: Frequently asked questions about re-hanging the door Biryusa

Is it possible to re-hang the door on a refrigerator Biryusa over 10 years old?

Yes, but for models before 2005 it may be required replacement of hinges or bushingsas their design is less universal. Also often found on old refrigerators metal hinges without adjustment, which complicates the process. Before starting work, check the availability of spare parts or contact the service center Biryusa.

Do I need to defrost the refrigerator before hanging the door?

For models with using a drip system defrosting is not necessary, but it is recommended remove food and shelves from the door compartmentsso that they do not interfere. For refrigerators No Frost it is enough to turn off the power for 10–15 minutes to stop the fan. Complete defrosting is only required if you plan replace the seal.

What to do if the door sags after rehanging?

Door sagging is usually due to insufficient fixation of the lower hinge or pin wear. Solutions:

1. Tighten the bolts of the lower hinge (but do not overtighten!).
2. Check whether the pin is loose in the hole. If yes, replace it or the entire hinge.
3. Install additional washer under the lower hinge to compensate for play.

If the sagging remains, it may have been deformed refrigerator body (for example, after moving). In this case, professional adjustment will be required.

How to rehang the door if a display is installed on it?

For models with a display (for example, Biryusa-22S) the algorithm is as follows:

1. Disconnect the refrigerator from the network.
2. Take a photo of the location of the wires and connectors on the door.
3. Carefully disconnect the connectors (usually they are secured with latches).
4. Reverse the door according to the standard instructions, do not pull the wires!
5. After installation, connect the connectors back and check the functionality of the display.

If after rehanging the display does not work or shows an error, check wire integrity and that the connectors are connected correctly. In rare cases, it may be necessary reset (see instructions for the model).

How long does it take to rehang the door?

If you have the tools and experience, the procedure occupies from 30 to 60 minutes. For beginners, it may take up to 1.5–2 hours, especially if the seal needs to be adjusted or replaced. Take your time - it is better to spend more time on careful dismantling than to later eliminate the consequences of haste (for example, a broken thread or a damaged seal).