Reversing the Bosch refrigerator door: video instructions and step-by-step analysis

Rearranging the refrigerator door Bosch is a task that many owners face when moving, renovating a kitchen, or simply wanting to optimize space. Despite the apparent complexity, the procedure does not require calling a specialist if you approach the matter systematically. In this article we will analyze not only the universal algorithm for most models (KGE36AW20R, KAN58A55, KGN39VL35R etc.), but also the nuances that the manufacturer is silent in the official instructions.

You will find out what tools you will need (spoiler: nothing exotic), how to avoid typical mistakes when removing hinges, and why the door may not close well after rehanging - even if everything is done “by the book.” And for visual learners, we have selected 3 verified videos with a step-by-step process from experienced craftsmen, including models with a display and system NoFrost.

Important: if your refrigerator is under warranty, moving the door automatically voids Bosch warranty (check the conditions in the product data sheet). Electronically controlled models (Home Connect) may require a reset after manipulation.

Preparation: tools and safety

Before you begin, make sure you have on hand:

• 🔧 Phillips screwdriver (better magnetic, so as not to lose the screws)
• 🔨 5 mm hexagon (for some models, for example, KAD92SX50R)
• 📏 Ruler or square (for checking gaps)
• 🧲 Magnet (to hold the door when working alone)
• 🧴 Silicone grease (for hinges after rearrangement)

Most refrigerators Bosch are equipped with a set of plugs for the holes for the hinges - they need to be moved to the opposite side. If there are no plugs (or they are lost), use decorative stickers the same color as the case. In models with a display (KAI90VI30R), it may be necessary. moving the screen power cable is a separate procedure, which we will discuss below.

⚠️ Attention: Do not try to hang the door if the refrigerator is connected to the network. Even when turned off, the compressor capacitor may retain a charge. Unplug the plug and wait 10 minutes. data-i="76">Before starting work, take a photo of:

Before starting work, take a photo of:

• 📸 Location of hinges and screws (top and bottom)
• 📸 Connecting wires (if there is a display or sensors)
• 📸 Position of the sealing rubber relative to the body

Removing the door: step-by-step instructions with photos

Let's start with the top hinge - it usually fixes the main load. The algorithm for most models:

1. Open the door 90° and place a book or a wooden block under it (so as not to damage the seal when removing).
2. Remove the decorative cover the hinges - it snaps on or is held on by one screw. In models Series 8 the cover can be glued - pry it off with a plastic card.
3. Unscrew the screws hinge fastenings (usually 2-3 pieces In refrigerators with a display, there is also a power connector here - carefully disconnect). it.
4. Holding the door, remove it from the bottom hinge by pulling up. If the door is “jammed”, check whether you forgot to unscrew the screw from the bottom.

For models with French door (KAN58A55, KAD92SX50R) the process is more complicated:

• 🔹 First, the small upper door (freezer) is removed.
• 🔹 Then the large door of the refrigerator compartment.
• 🔹 Lower the hinge in such models is often hidden under the decorative panel - it needs to be removed by prying it with a screwdriver.

If the door after removal “walks” in the hinges or the springs are hanging, this is normal. The main thing is not to lose plastic bushingswhich often fall out during dismantling. In models Bosch Series 6 the bushings can be metal - they need to be lubricated before reinstallation.

Moving the hinges to the other side: diagrams and nuances

Now you need to move the hinges to the opposite side. There are several critical points here:

For models with asymmetrical loops (for example, built-in Bosch) are supplied with a stencil for drilling new holes. If there is no stencil, use the old holes as a template:

1. Attach the loop to the opposite side.
2. Mark the centers of future holes with a pencil.
3. Drill the holes drill ∅4 mm (for most screws).

⚠️ Attention: In refrigerators with a system NoFrost (KGE36AI40R), when moving the hinges, the air duct may move. After installing the door, check whether it blocks the flow of cold air - otherwise the freezer will freeze.

If your model has door opening sensor (the light flashes when opening), it also needs to be moved. Usually it is attached to one screw inside the case - carefully disconnect the connector and move the sensor to the other side.

What to do if the holes for the hinges do not match?

If the refrigerator body does not have symmetrical holes for the hinges (relevant for older models or built-in options), you will have to drill new ones. Use a metal drill ∅4–5 mm and be sure to cover the drilling site with masking tape so as not to damage the enamel. After installing the hinges, treat the edges of the holes with an anti-corrosion compound (for example, WD-40).

Installing the door on a new side: procedure

Now we assemble everything in the reverse order, but taking into account the nuances:

1. Place the door on the lower hinge, holding it at an angle of 45°. In models with NoFrost make sure that the seal does not wrinkle.
2. Secure the upper hinge, but do not tighten the screws all the way - the door should “play” a little for adjustment.
3. Check the gaps:
   • 📏 On the sides - 2-3 mm (for free movement)
   • 📏 On top - 1-2 mm (so that the seal does not rub against the body)

Adjust the position doors, tightening or loosening the screws hinges. If the door opens spontaneously, you need to move it down a little.

For models with display (KAN58A55, KAI90VI30R) after installing the door:

1. Connect the screen power connector (it is usually marked in red or blue).
2. Turn on the refrigerator and check if the display lights up. If not, double-check the polarity of the connection.
3. Reset the settings to factory settings through the menu Settings → Reset (if the display does not work correctly).

Adjusting the door after rehanging

Even if the door is visually level, it needs to be adjusted for proper operation. Here's what we check:

• 🔄 Spontaneous opening: if the door “moves” back, loosen the top hinge and move the door 1-2 mm down.
• 🚪 Cracks in the seal: do a test with a sheet of paper - it should be pressed tightly around the entire perimeter. If the paper falls out, tighten the hinges or adjust the bracket.
• 🔊 Creaks or extraneous sounds: lubricate the hinges with silicone grease (do not use WD-40 - it corrodes the plastic).

In refrigerators with NoFrost after re-hanging the door, air circulation may change. If after 24 hours you notice:

• ❄️ Ice in the freezer
• 🌡️ Uneven cooling (one corner is warmer)
• 💨 Loud fan noise

this means the door is blocking the air duct. The solution is to move it 3–5 mm to the side (by loosening the hinges) or check the position of the internal partitions.

⚠️ Attention: In models with linear compressor (Bosch Serie 8) after re-hanging the door, the calibration of the sensors may be lost. If the refrigerator starts to turn on more often or an error appears on the display E:02, perform a reset: turn off the power for 10 minutes, then turn on and hold the button Super Cooling 5 seconds.

Typical errors and how to find them avoid

Even experienced craftsmen sometimes make mistakes when hanging a door. Here are the most common ones:

Error	Consequences	How to fix
Did not rearrange the hole plugs	Dust and moisture get into the case, corrosion	Close the holes with standard plugs or sealant
The hinges are too tight	The door warps, the seal is deformed	Loosen the screws, adjust the gaps
The magnetic seal was not moved	The door does not close tightly, there is ice	Remove the seal and move it to the new side
The display cable is damaged	The screen does not work, errors E:24, E:25	Check the integrity of the wire, solder if broken

Especially often errors occur when working with two-chamber models (KAN58A55, where you need to synchronize the position of both doors. If, after rehanging:

• 🔹 The top door (of the freezer) closes normally, but the bottom door (of the refrigerator) does not, check middle hinge (it may be displaced).
• 🔹 The doors “touch” each other when opening, adjust tilt angle the upper hinge.

For models with Home Connect after rehanging, it may be necessary reconnecting to Wi-Fi. Go to the application, select the refrigerator and execute the command Reconnect the device.

Video instructions: the best rollers for different models

Theory is good, but a visual demonstration simplifies the task significantly. We have selected 3 verified videos with detailed analysis:

• 📺 For classic models (KGE36, KGN39): "We rehang the Bosch door in 15 minutes" (channel “Home Appliance Repair”) The author shows how to do it without an assistant, using a magnet and available tools.
• 📺 For Side-by-Side (KAN58, KAD92): "Complicated case: Bosch French door" (channel “Cold Master”) Here are the nuances of moving the display cable and adjusting the middle hinge.
• 📺 For built-in models (KAI90, KUL15): "Re-hanging the door of a built-in Bosch refrigerator" (channel "Kitchen Appliances"). holes.

Pay attention to the comments under the video - they are often discussed hidden problems, which are not voiced in the video itself. For example, in. model KGE36AI40R after re-hanging, the temperature sensor may need to be reconfigured (instructions in the comments from the user @HolodMaster24).

If you have not found a video for your model, look for videos by refrigerator series (for example, “Bosch Serie 6 door reversal”). Usually the process is identical for all models of the same line.

FAQ: answers to frequently asked questions

Is it possible to rehang the door of a Bosch refrigerator yourself if it is under warranty?

Technically, yes, but this cancels the warranty on the refrigerator. The manufacturer considers hanging the door to be an intervention in the design. If the refrigerator is new (up to 1 year), it is better to call a service center Bosch —they will do it free of charge under warranty (the service may be paid, please specify when ordering).

How long does it take? rehanging the door?

For classic models (KGE36, KGN39) - 30-60 minutes. For Side-by-Side or French doors - 1.5-2 hours (due to moving cables and adjusting several hinges, add another 20-30 minutes). data-i="239">What to do if, after rehanging, the door does not close tightly?

What should I do if the door does not close tightly after rehanging?

The reasons may be different:

1. The seal is deformed — try heating it with a hairdryer (50°C) or replace it.
2. The hinges are overtightened — loosen the screws and adjust the gaps (2–3 mm on the sides).
3. The magnetic circuit has shifted —check that the metal plate on the body matches the magnet in the seal.
4. The door is skewed —remove it and reinstall, leveling it.

If the problem persists, take a photo of the gaps and contact service - the case may be deformed.

Do I need to defrost the refrigerator before re-hanging the door?

Required! for NoFrost-models. Turn off the refrigerator, remove all the food and wait until the ice in the freezer melts.

• 🔹 Preventing short circuits (water + electricity).
• 🔹 Ease of operation - a door with ice is heavier and can damage the hinges when removed.
• 🔹 Checking the seal - in the cold the rubber becomes hard and you will not notice defects.

Is it possible to hang the door on a Bosch refrigerator with a display, not turning it off?

No! The display is connected to the main board, and when moving the loops you risk:

• 🔹 Damaging the cable (broken wires).
• 🔹 Losing the settings (if you do not reset).
• 🔹 Get an electric shock (capacitors may be charged).

Unplug the refrigerator, wait 10 minutes and only then start working. After installing the door, turn on the power and check the operation of the screen.