Reversing the refrigerator door Indesit is a task which many owners encounter when moving, renovating a kitchen, or simply wanting to optimize space. Despite the apparent complexity, the procedure does not require professional skills if you strictly follow the algorithm and take into account the design features of the model. The main thing is to take your time and prepare all the necessary tools in advance.
In this article we will analyze the process of rearranging the door for refrigerators Indesit with an upper and lower freezer, indicate typical mistakes that lead to distortions or broken hinges, and give recommendations for adjustment after installation. We will pay special attention to models with electronic display and systems No Frost, where outweighing has its own nuances. If your refrigerator was manufactured after 2018, check for the presence of plastic plugs on the opposite side - their absence may mean that the model does not support double-sided fastening.
Before you begin, please note: the procedure will take from 1 to 3 hours depending on experience and equipment. Some models (for example Indesit ITF 118 or Indesit BIAA 13) require complete removal of the door, while in others it is enough to rearrange the hinges. To avoid damage to the seal or housing, carefully study the mounting diagram for your modification.
Preparation: tools and safety precautions
To hang the refrigerator door Indesit you will need:
- 🔧 Phillips screwdriver (usually PH2) - for most hinges and fasteners.
- 🔧 Socket wrench or 10 mm socket —for nuts on some models (for example, Indesit C 132 G).
- 📏 Ruler or square —to check the evenness of the installation.
- 🧲 Magnet or tape — for temporary fixation of screws and nuts.
- 🧴 Silicone grease —for processing hinges after rearrangement.
Before starting work be sure to unplug the refrigerator and defrost it if there is ice on the walls. This will prevent a short circuit and make it easier to manipulate the door. Make sure there is enough space around it - at least 1 meter on the side where the door will move. If the refrigerator is in a niche, you will have to pull it out.
⚠️ Attention: Do not turn it over. refrigerator door Indesit with system No Frost upside down - this can damage the drainage system and lead to condensation accumulation inside the case. Always place it on a soft surface (for example, a blanket) vertically.
Also prepare a container for small parts. (screws, washers, plugs) - they are easy to lose. If the refrigerator is supplied with decorative covers on the hinges, remove them carefully, prying them off with a flat screwdriver so as not to scratch the plastic.
Determination of the type of door fastening: what kind of hinges there are
Refrigerators Indesit equipped with one of three types of hinges, on which the re-hanging algorithm depends:
- Standard top and bottom hinges - the most common option (models Indesit BIA 18, Indesit ITF 118). data-i="88">Standard upper and lower hinges
- Hidden hinges —found in premium series (for example, Indesit XWA 81482 XThe hinges are hidden under decorative panels, and the door is fixed at four points. Here you will need to remove the lining.
- Central hinge - typical for models with French door (for example, Indesit BIAA 20The door is attached to one hinge in the middle, which simplifies hanging, but requires precise adjustment.
To determine the type of hinges, inspect the side walls of the refrigerator:
- 🔍 If you can see two round plugs on the opposite side, you have standard hinges.
- 🔍 If there are no plugs, but there is a vertical bar - these are hidden hinges.
- 🔍 If the loop is one and located in the center - this is central fastening.
For models with hidden hinges additionally required flat screwdriver to remove decorative panels. In some cases, the hinges can be secured not only with screws, but also with latches - they must be bent carefully so as not to break.
What to do if There are no plugs on the opposite side?
The absence of plugs may mean that the model does not support hanging the door. In this case, you will have to purchase an additional set of hinges for the other side (the article number is indicated in the instructions for the refrigerator). For models after 2020, it is sometimes necessary to order parts from an official dealer, since they are not included in the basic one. complete set. Indesit after 2020, it is sometimes necessary to order parts from an authorized dealer, since they are not included in the basic package.
Step-by-step instructions: how to remove the door of an Indesit refrigerator
The process of removing the door is the same for most models with an upper/lower freezer. We will look at the algorithm using an example Indesit BIA 18:
- Remove the decorative trims from the hinges (if any), prying them with a screwdriver.
- Unscrew the top hinge:
- 🔧 Hold the door with one hand (it may fall after unscrewing the last screw!).
- 🔧 Unscrew 2-3 Phillips screws a screwdriver.
- 🔧 Remove the hinge and set it aside along with the screws.
- 🔧 Lift the door up to remove it from the grooves.
- 🔧 If the door does not budge, check whether the seal is in the way - you can bend it slightly.
- Unscrew the bottom hinge and remove it from the body.
- Move the door to soft surface (for example, on a table covered with a blanket).
For models with freezer compartment. below (for example, Indesit BIAA 13) the algorithm is similar, but the bottom hinge may have an additional lock. If the freezer door is removable, it will also have to be removed.
☑️ Checklist before removing the door
Pay special attention seal do not pull on it when removing the door, so as not to deform it. If the seal is glued and not inserted into the groove, you will have to carefully. separate with a knife (but this is rare for Indesit).
Moving hinges to the other side: nuances and mistakes
After removing the door, you need to move the hinges to the opposite side. There are several critical points:
- Remove the plugs on the other side of the refrigerator (if there are any). Pry them off with a screwdriver or a knife. In some models, the plugs are glued - they can be heated with a hairdryer for easy removal.
- Check the holes for the hinges:
- 🔍 If there are no holes, you will have to drill them. (the diameter is indicated in the instructions).
- 🔍 If there are holes, but are closed with plastic inserts, remove them.
- 🔧 The top loop on the right side becomes the bottom on the left, and vice versa.
- 🔧 Do not confuse the hinges - they may differ in design!
- Secure the hinges screws from the kit. Do not tighten them completely - you need to adjust the door first.
On models Indesit with an electronic display (for example, Indesit EWD 8140), the wiring harness may need to be moved when re-hanging the door. It is usually attached to the loop using plastic ties - you need to carefully cut them and fix the harness on the new loop.
⚠️ Attention: If, when transferring the loops, you find that the screws do not screw into the new holes (for example, due to the threads being misaligned), do not apply force. It is better to use thread lock (for example, Loctite 243) or select screws with a smaller diameter.
For models with No Frost system After re-hanging the door, be sure to check the operation of the fan. If it starts to make noise or rattle, it means that the door is not installed airtight and requires additional adjustment.
Door installation and adjustment: how to avoid distortions
Now you can begin installing the door on the new side. Follow this algorithm:
- Place the door on the lower hingelifting it so that the pin fits into the groove.
- Align the door vertically —it should stand level, without tilting. Use a level or visually check the gaps at the top and bottom.
- Secure the top hinge, but do not tighten the screws all the way.
- Check the tightness:
- 🔍 Close the door and pull the seal in different places - the resistance should be the same.
- 🔍 Place a sheet of paper between the seal and the body - if it falls out, adjustment is needed.
- 🔧 If the door sags - tighten the lower hinge.
- 🔧 If the door touches the body - loosen the upper hinge and move the door in the desired direction.
For precise adjustment, use hex key (usually included with the refrigerator). Turn the adjusting screw on the hinge clockwise to raise the door and counterclockwise to lower it. The optimal gap between the door and the body is 2–3 mm.
| Problem | Cause | Solution |
|---|---|---|
| The door does not close tightly | The hinges are skewed or the seal is deformed | Adjust the hinges, check the seal for damage |
| The door touches the body when opening | Incorrect position of the top hinges | Loosen the hinge and move the door to the side |
| Creak when opening/closing | Lack of lubrication or debris getting into the hinges | Clean and lubricate the hinges with silicone lubricant |
| Condensation on the seal | Tightness failure | Check the fit of the seal, adjust the door |
After adjustment, close the refrigerator and wait 10-15 minutes. Then check the temperature inside - if it starts to rise, it means the seal is broken. In this case, repeat the adjustment or check the seal for cracks.
Features of rehanging for models with a freezer compartment
Refrigerators Indesit with a lower or upper freezer (for example, Indesit BIAA 13 or Indesit C 132 G) have two separate doors, and rehanging each of them has its own nuances:
- 🔧 For the upper freezer:
- First, the refrigerator door is removed, then the freezer door.
- The freezer door is usually heavier, so it is better to remove it with an assistant.
- 🔧 For the bottom freezer:
- The freezer hinges can be hidden under the decorative panel.
- When installing, check whether the vegetable drawer is in the way - sometimes it needs to be temporarily removed.
- 🔧 For Side-by-Side models:
- Reversing the doors requires complete dismantling of the middle partition.
- Hinges in such models often have additional clamps.
In refrigerators with with one door for both chambers (for example, Indesit ITF 118) the algorithm is simpler, but the weight of the door increases. An assistant is definitely needed here to hold the door while removing it. Also note that in such models the seal may be double - it must be checked especially carefully.
⚠️ Attention: In models Indesit with electronic control (display on the door), when reversing, it may be necessary to move the control unit. If you are not confident in your skills, it is better to contact a service center - incorrectly connecting the wires will lead to a failure of the program.
Common mistakes and how to avoid them
Even if you carefully follow the instructions, you can make errors that will lead to breakdown or incorrect operation of the refrigerator. Here are the most common of them:
- 🚫 Use of unsuitable tools —for example, screwdrivers of the wrong size. This leads to the breaking of the slots on the screws.
- 🚫 Tightening the hinges - because of this, the door may be deformed or the hinges will burst under load.
- 🚫 Ignoring the plugs - if they are not removed before installation hinges, you can damage the case.
- 🚫 Incorrect position of the seal —it should fit evenly around the entire perimeter.
- 🚫 Lack of lubrication —without it, the hinges will quickly begin to creak and wear out.
Another typical error is ignoring the weight of the door. If the refrigerator is placed on an uneven surface, the door may open spontaneously after being rebalanced. To avoid this, use adjustable legs to level the body.
If, after rehanging, the refrigerator Indesit starts to work loudly, check:
- 🔍 Does the fan touch the door (in models with No Frost).
- 🔍 Are the wires pinched (in models with a display).
- 🔍 Has the compressor moved due to vibrations when removing the door.
FAQ: answers to frequently asked questions
Is it possible to hang the Indesit refrigerator door without an assistant?
Technically yes, but this is risky - the refrigerator door weighs from 10 to 20 kg (depending on the model). Without an assistant, there is a high chance of dropping it or damaging the hinges. If you work alone, use supports (for example, a chair) and safety belts.
What to do if the door does not close after hanging?
The reasons may be different:
- 🔧 The hinges are not adjusted - tighten or loosen them.
- 🔧 The seal is deformed - try to restore its shape with hot water.
- 🔧 The refrigerator body is uneven - level it using the legs.
If there is a problem is not resolved, check if the door body is bent when removed.
Is it necessary to defrost the refrigerator before rehanging it?
Yes, if there is ice or frost on the walls. When melting, water can get on the electrical contacts (for example, in models with a display) and cause a short circuit, which adds weight to the door. makes it difficult to remove.
How to hang a door if there are no holes for hinges on the other side?
In this case, you will have to drill the holes yourself. Use a metal drill with the diameter specified in the instructions (usually 5–6 mmPre-apply masking tape to the drilling site). do not scratch the case. If you are not confident in your skills, contact the service.
Is it possible to hang the door on an Indesit refrigerator with the No Frost system?
Yes, but with caution, it is important not to damage the ventilation system and not to pinch the wires (if they go through the loop). After re-hanging, check the operation of the fan - it should rotate freely, without extraneous sounds.