Rearranging the refrigerator door LG is a task that many owners face when moving, renovating a kitchen, or simply wanting to optimize space. Unlike models of other brands, the equipment of the Korean manufacturer has its own design features: from the location of the hinges to the fastening of the dispenser (if there is one). Incorrect dismantling can lead to damage to the seal, warping of the door, or even breakdown of the electronic unit - this is especially true for models with a system SmartThinQ.
In this article you you will find step-by-step instructions taking into account all the nuances: from preparing tools to final adjustment. We will look at how to hang the door on refrigerators LG with and without a water dispenser, as well as on models with a French door (French Door). We will pay special attention to the typical mistakes that beginners make - their consequences are more expensive than calling a specialist.
If your refrigerator is under warranty - recheck the terms of service. Some dealers LG consider moving the door yourself a violation of the warranty. Check this point in the documents or with an official representative.
1. Preparation: tools and safety
Before you get started, make sure you have everything you need. Without the right tools, you risk breaking fasteners or damaging plastic parts —this is especially true for models with hidden hinges (for example, LG GR-B207SLQZ).
You you will need:
- ✅ Phillips screwdriver (preferably magnetic, so as not to lose the screws)
- ✅ Hex key (size depends on the model, usually 4 or 5 mm)
- ✅ Flat screwdriver or plastic pick for removal decorative panels
- ✅ Wrench (for hinges on some models)
- ✅ Making tape (to secure the door during operation)
- ✅ Level (to check evenness after installation)
Also prepare the workspace:
- 📦 Empty the refrigerator of food and unplug it.
- 🧊 Let it stand for 1-2 hours with the door open door to avoid condensation on the seal.
- 🧹 Place a soft cloth or cardboard under the door - this will protect the floor from scratches.
⚠️ Attention: If your refrigerator is equipped with linear compressor Inverter Linear, after moving the door it may need sensor calibration. flashing light or error on the display. In this case, follow the instructions for the specific model.
2. Determine the type of door fastening
LG uses three main types of hinges, and the algorithm of actions depends on this:
| Hinge type | Refrigerator models | Features |
|---|---|---|
| Open hinges | LG GA-B419, GR-B247 | Screws are visible outside, rearrangement takes 20–30 minutes |
| Hidden hinges | LG GC-B247, GR-B207 (Door-in-Door series) | Removal of the decorative cover is required, risk of damage to the plastic |
| Hinges with gas shock absorber | LG GR-M207, models with French Door | Care is required when disconnecting the shock absorber, otherwise the door will fall |
To find out the type of hinge on your model, inspect the top and bottom corners of the door. If the screws are hidden under a plastic cover, this is a hidden type. On models with a dispenser (LG GR-D247SL), the hinges are often combined: the upper one is open, the lower one is hidden.
Also pay attention to the direction of opening. On some refrigerators LG with an electronic display (SmartThinQ), after rehanging it is required reset door settings through the menu. This option is in the section Settings → Door. → Opening direction.
How to check the LG refrigerator model?
The model number is indicated on the sticker inside the chamber (usually on the left) or on the back wall Format: two letters (series), then numbers and letters (modification), For example, GA-B419SLQZ, where GA - series, B419 —volume and type.
3. Step-by-step instructions: removing the old door
Let's start with dismantling. The main rule: remove the door carefully so as not to damage the cable wires (on models with a dispenser) or a seal.
Procedure:
- Close the door and secure it with masking tape in two places (top and bottom).
- If there are decorative trims on the hinges, pry them off with a flat screwdriver and remove.
- Unscrew the top hinge screws (usually 2-3 pieces). Hold the door! On models with a gas shock absorber, first disconnect it.
- Gently lift the door up to remove it from the bottom hinge. If it is tight, check that all the screws are unscrewed.
- Put the door on a prepared surface (for example, on a table covered with a blanket).
On refrigerators with a dispenser (LG GR-D247SLQZ) before removing the door you must:
- 🔌 Disconnect the cable from the main unit (the connector is usually located under the top hinge).
- 📱 Take a photo of the connection diagram so as not to confuse it during reassembly.
⚠️ Attention: If after removing the door you see rust on the hinges - this is a signal of high humidity in room. Before installation, clean the metal and apply silicone grease.
☑️ Checklist before removing the door
4. Transferring the loops to the other side
Now you need to move the loops to the opposite side. It is important here do not confuse the upper and lower loops they are often not interchangeable!
Algorithm:
- Remove the plugs on the opposite side (where the new holes will be). They are usually held on by latches.
- Move the hinges to the other side, aligning the holes (LG GC-B247) may be required. data-i="150">—to do this, use a metal drill (∅ 4–5 mm). drill new holes — for this use a metal drill (∅ 4–5 mm).
- If the hinges are asymmetrical (for example, on models with French Door), check their markings:
L(left) andR(right). - Tighten the screws, but not all the way - leave some play for adjustment.
For refrigerators with dispenser additionally:
- 🔧 Move the cable mount to the other side (usually there are symmetrical grooves).
- 💧 Check the water supply tube - it should freely reach the new door position.
On models LG Door-in-Door (for example, GR-D247SL) the inner door is attached separately. It also needs to be removed and re-hanged, but the screws there are smaller and require a 3 mm hexagon.
5. Door installation and adjustment
The most important step is to hang the door back. If this is done incorrectly, over time it will sag and the seal will no longer fit tightly.
Assembly procedure:
- Carefully put the door on the lower hinge, holding it by the upper edge.
- Align it in the center and lower it until it stops.
- Tighten the screws of the upper hinge, but do not tighten them completely.
- Check how the door closes: it should fit evenly, without slots.
- If there is a misalignment, loosen the screws and adjust the position.
For models with a dispenser:
- 🔌 Connect the cable cable to the connector (watch the polarity!).
- 💡 Turn on the refrigerator and check the operation of the dispenser. If water does not flow, check the tube for bends.
After installation:
- 📏 Use a level to check the vertical evenness of the door.
- 🧴 Apply silicone grease to the seal - this will extend its service life.
⚠️ Attention: If, after rehanging, the refrigerator LG began to hum loudly, check whether the door is touching the body. This can lead to vibration and damage to the compressor.
6. Typical mistakes and how to avoid them
Even with the apparent simplicity of the process, many make mistakes, which are then costly. Here are the most common:
- ❌ The upper and lower hinges are mixed up → the door does not close or sags. Solution: check the markings on the hinges (
TOP/BOTTOM). - ❌ The screws are too tight → over time, the thread breaks. Solution: use a torque wrench (force 1.5–2 N m).
- ❌ The seal is damaged → refrigerator stops freezing. Solution: Before work, seal the seal with masking tape.
- ❌ Plugs are not transferred → holes from old hinges are visible. Solution: use decorative covers from the kit.
- ❌ Forgot to disconnect the dispenser cable → short circuit. Solution: always take a photo of the connection diagram.
On models with electronic display (LG SmartThinQ) after re-hanging, an error may appear dE (door error). This means that the door sensor does not work. Solution:
- Check whether the sensor cable is pinched.
- Reset the error through the menu:
Settings → Diagnostics → Resetting sensors. - If the error remains, the control unit needs to be re-flashed (it is better to contact service).
If you notice that after the rearrangement the refrigerator has become worse at freezing, check tightness of the seal with a sheet of paper. Close the door by inserting the sheet between the seal and the body. If it falls out, adjustment is needed.
7. Features for LG refrigerators with French Door
Models with a French door (LG GR-M207SL, GC-X247MC) have a more complex design: two upper doors and a lower drawer. Re-hanging here takes 2-3 times more time and requires care.
What needs to be taken into account:
- 🔄 Hinges of the upper doors synchronized - they need to be rearranged in pairs.
- 📦 Lower the drawer has separate guides, which also require relocation.
- ⚡ Electronic unit is often located in the upper part - do not pull the wires when working!
Procedure:
- First remove the upper flaps (as described above).
- Pull out the bottom drawer and unscrew the guides.
- Move the fasteners to the other side, paying attention to symmetry.
- Install the drawer back, then hang the upper doors.
On models with Twin Cooling after rearrangements may be required recalibration of temperature sensors. To do this:
- Press and hold the button
Freezer(freezer) for 5 seconds. - Wait sound signal and blinking indicator.
- The refrigerator will automatically perform self-diagnosis.
⚠️ Attention: On refrigerators LG French Door with a system Instaview (transparent door) after rehanging, it may be required resetting the sensor. If the door does not open after knocking twice, contact service.
FAQ: Frequently asked questions about rearranging the LG door
Is it possible to re-hang the door on an LG refrigerator yourself if Is it under warranty?
Formally, independent intervention can be considered a violation of the warranty terms. However, if you do not damage the parts and do not break the seals, the service center may not notice the changes. It is better to check this point with an authorized dealer LG before starting work.
How much does it cost to rehang the door at the service center?
The cost of the service depends on the model and region. On average:
- Refrigerators without a dispenser: 1,500–2,500 ₽
- Models with a dispenser: 2,500–4,000 ₽
- French Door: 3 500–5 000 ₽
The price includes labor and adjustment, but does not include the cost of spare parts (if required replacing hinges or seals).
What to do if, after rehanging, the door does not close tightly?
Causes and solutions:
- Disk of the hinges → loosen the screws and adjust the position.
- The seal is damaged → try to restore its shape with a hairdryer (temperature 50–60°C) or replace it.
- The magnetic latch is in the way → check its position and, if necessary, move it to the other side.
Necessary Is it possible to reprogram the refrigerator after reversing the door?
Only for models with electronic control (SmartThinQ, Inverter Linear). Usually you need to:
- Reset the door settings in the menu.
- Calibrate the sensors (if the refrigerator gives an error).
On mechanical models (LG GA-B309), programming is not necessary.
Is it possible to overweight door on an LG refrigerator with an ice maker?
Yes, but it is more complicated due to the additional tubes and wires. Important:
- Turn off the water supply before working.
- Move the ice maker tube to the other side, avoiding kinks.
- Check the tightness of the connections after installation.
If you are not sure, it is better to call a technician, as a leak can damage the electronic unit.