Rearranging the door on the refrigerator Liebherr is a task that every owner faces sooner or later. The reasons may be different: remodeling the kitchen, changing the arrangement of furniture, or a banal desire to make opening more convenient. Fortunately, the manufacturer has provided this option for most models, and you do not have to contact a service center. However, the process requires accuracy and knowledge of key nuances - from the correct selection of tools to taking into account the features of a specific series of refrigerators.
In this article we will figure out how to hang the door on a refrigerator Liebherr without the risk of damaging the mechanism or seal. You'll learn which models support this feature, what tools you'll need, and how to avoid common mistakes. We will also share life hacks that will save you time - for example, how to temporarily fix a door while working or what to do if the fasteners are rusty. Are you ready? Then let's get started!
Preparation: checking the possibility of re-hanging
Before taking a screwdriver, make sure that your model Liebherr generally supports re-hanging the door. Most modern brand refrigerators have this option, but there are exceptions. For example, some built-in models or devices with non-standard design (for example, series Monolith or Bluespace) may have rigidly fixed hinges.
How to check?
- 🔍 Inspect top and bottom hinges the doors: if there are plugs or holes for fastenings on the opposite side, the model supports re-hanging.
- 📄 Look at operating instructions (section "Installation" or "Installation"). It can be found in electronic form on the website Liebherr by model number.
- 🔧 Check the package contents: the box should contain spare plugs for the holes and, possibly, a key for adjusting the hinges.
If your refrigerator belongs to the Premium, Comfort or BioFreshseries, most likely there will be no problems. But for models with water dispenser (for example, Liebherr SBSes 7256), the process may become more complicated due to additional tubes and wiring - here it is better to enlist the help of a second person.
⚠️ Attention: Refrigerators Liebherr with system NoFrost in the freezer compartment require special care when removing the door - there may be seal heating elements inside. Do not pull the door sharply so as not to damage the wiring!
Required tools and materials
For work you will need a minimum set of tools, but some of them must be exact shape and sizeto avoid damaging the fastenings. Here is the complete list:
| Tool/material | Purpose | Notes |
|---|---|---|
| Phillips screwdriver (PH2) | For unscrewing hinges and plugs | Preferably with a magnetic tip |
| Hex wrench (4 or 5 mm) | Adjusting hinges (if required) | Included in some models |
| Flat screwdriver | Removing plugs and prying up decorative panels | Thin so as not to scratch the surface |
| Wrench (10 mm) | For the bottom hinge bolts (if yes) | Not always required |
| Making tape | Fixing the door during operation | A width of 5 cm is enough |
Also prepare:
- 🧴 Silicone grease (for example, WD-40) - if the fasteners are rusty or difficult to unscrew.
- 🧼 Soft fabric - to place under the door when removing and not scratch the floor.
- 📦 A box or stand - for neat placement of the removed door.
Step-by-step instructions: removing the old door
Start with the top hinge - this will simplify the further process. Follow the algorithm:
Unplug the refrigerator and get all the products from the door shelves (they may fall out when tilted).
Seal the door with masking tape in two places - on top and from below - so that it does not fall when the fastenings are loosened.
Remove decorative plugs from the hinges: pry them off with a flat screwdriver (carefully so as not to break them!). Under them you will see fastening bolts.
Unscrew the bolts top hinge with a Phillips screwdriver. Hold the door with your hand - after removing the last bolt, it may move.
Lift the door up and remove it from the bottom pin. If it is tight, rock it slightly from side to side.
Lay the door on the prepared surface face upto avoid damaging the seal.
Now repeat the process for of the lower hinge (if your model has one). In some refrigerators Liebherr the lower hinge is fixed not with bolts, but with a pin and nut it needs to be unscrewed with a wrench.
What to do if the bolts do not unscrew?
If the fasteners are “stuck”, apply to them WD-40 and wait 10-15 minutes. Do not apply excessive force as this may strip the threads. As a last resort, use an impact screwdriver or contact service.
In refrigerators Liebherr with a system BioFresh there may be temperature and humidity sensors inside the door. When removing the door, do not pull the wires - carefully disconnect the connectors (they are usually marked with a colored mark).
Re-hang the hinges to the other side
This is the most critical stage. It is important here not to confuse left and right fastenings they may look the same, but have different threads or shapes. The refrigerator usually comes with spare plugs for the holes on the opposite side.
We proceed step by step:
Remove the plugs from on the opposite side the body (where the door will now be). Under them you will see threaded holes.
Move top loop to the new side and tighten the bolts. Do not tighten them completely - leave some play for adjustment.
Install the lower hinge (or pin) in the same way. In some models (Liebherr CBPes 4866), the lower hinge has adjusting screw —it must be unscrewed before installation.
Check that all sealing rubbers on the hinges are intact and correctly positioned.
If your model has middle hinge (for example, in refrigerators with French Door), it also needs to be moved. Usually it is fastened with two bolts and has a groove for fixing the door.
The plugs have been removed from the new side|The hinge bolts are screwed in, but not tightened|The rubber seals are in place|The wires (if any) are not twisted-->
We install the door in a new place
Now we carefully lift the door and hang it on the hinges. Here it is better to work with an assistant - the door can be heavy (especially in models with double glassas in the series Bluespace).
Procedure:
Lift the door and put it on lower pin hinges. Make sure it is seated all the way.
Lower the door so that top hinge you may have to slightly raise or lower the door for an accurate fit.
Tighten the bolts of the top hinge, but not all the way - leave room for adjustment.
Check that the door fits evenly to the body along the entire perimeter. If there are distortions, loosen the bolts and adjust the position.
After preliminary installation, close the door and check:
- 🔄 Ease of movement —the door should open/close without effort.
- 🚪 Gaps —there should be no gaps between the door and the body wider than 2 mm.
- 🔊 Sound —there should be no creaks or knocks when closing.
Adjustment and final checks
Even if the door is visually level, it needs adjust to fit perfectly. This affects the tightness and, as a result, the energy consumption refrigerator. Here's how to do it:
1. Vertical adjustment (if the door sags or touches the bottom):
- Loosen the bolts of the lower hinge.
- Raise or lower the door to the desired level.
- Tighten the bolts and check the movement.
2. Horizontal adjustment (if the door is skewed on the sides):
- Loosen the bolts top hinge.
- Move the door to the left or right.
- Tighten the bolts and check the fit of the seal.
3. Checking the seal:
- Take a sheet of paper and clamp it between the door and the body.
- If the sheet easily pulled out - the seal needs to be adjusted or replaced.
- Carry out a test along the entire perimeter.
After adjustment, turn on the refrigerator and let it run for 1-2 hours. Then. check:
- 🌡️ Temperature in the chambers - it must correspond to the specified one.
- ❄️ Ice - if the seal does not fit tightly, frost may appear on the walls.
- 🔋 Energy consumption — after re-hanging it should not increase significantly.
⚠️ Attention: If after re-hanging the refrigerator Liebherr with the system SmartDevice (for example, Liebherr SBS 86I2 Premium) shows an error on the display, reset the settings via menu Settings → System → Reset. This is due to a change in the position of the sensors.
Typical errors and how to avoid them
Even with the apparent simplicity of the process, many make mistakes that then have to be corrected in the service center. Here are the most. common:
| Error | Consequences | How to avoid |
|---|---|---|
| Tightening the hinge bolts | Thread breakage, cracks in plastic parts | Tighten the bolts with a force of no more than 2–3 Nm |
| Ignoring wiring (in models with a display) | Short circuit, errors on the screen | Turn off the power and carefully disconnect the connectors |
| Incorrect position of the seal | Leaks, ice, increased energy consumption | Check the fit with a sheet of paper |
| Use of inappropriate tools | Torn edges of bolts, scratches on case | Use only a PH2 Phillips screwdriver and a 4-5 mm hexagon |
Another common problem is creaking of the door after re-hangingIt occurs due to:
- 🔧 Insufficient lubrication of the hinges —use silicone grease, but not oil!
- 🔄 Door skew —check the adjustment again.
- 🧲 Magnetic sealthat rubs against the body—gently bend it it.
If after all the manipulations the door still does not close tightly, the seal may be worn out. In this case, it is needed replace - original rubber seals for Liebherr can be ordered by number. model.
FAQ: answers to frequently asked questions
Is it possible? rehang the door on a Liebherr refrigerator with a water dispenser?
Yes, but the process is more complicated due to additional pipes and wiring. In models like Liebherr SBSes 7256 you will have to:
- Turn off the water supply and drain the remaining water from the system.
- Carefully disconnect the hoses and wires (they are usually marked in color).
- Move the dispenser mounts to the other side.
If you are not sure, contact the service.
How long does re-hanging take?
On average - 1–2 hours, if everything goes smoothly. The longest thing to do is adjust and check the tightness. For the first time, you can spend up to 3 hours.
Do you need to defrost the refrigerator before reinstalling?
No, if you work quickly. (more than 30 minutes), it is better take out the food to let the refrigerator stand turned off to avoid ice.
What to do if after re-hanging the refrigerator began to work louder?
This may be due to:
- 🔧 By skewing the door —check the adjustment.
- 🔄 By shifting the compressor (if the refrigerator was uneven).
- 🧲 Friction of the seal —lubricate it with silicone grease.
If the noise does not disappear, check the level of the refrigerator (it should be level).
Is it possible to rehang only the top door in a French Door refrigerator?
Technically yes, but this is not recommendedB. models Liebherr with French Door (for example, Liebherr SBS 86I2) the doors are balanced among themselves. Re-hanging only one can lead to:
- 🔄 Distortion and uneven wear of the hinges.
- 🚪 Problems with tightness.
- 🔊 Increased noise when opening.
It is better to rehang both doors at once.