We rehang the door of the Pozis refrigerator yourself: from A to Z

Rearranging the refrigerator door Pozis is a task that every owner faces sooner or later. The reasons may be different: moving, changing the layout of the kitchen, inconvenient opening, or even a banal desire to update the interior. Fortunately, most models Pozis (from classic RK-102 to modern Pozis RK-149W) support this option, but the process requires accuracy and knowledge of key nuances.

Unlike Western brands, where re-hanging the door often comes down to rearranging the hinges, in refrigerators Pozis (especially in models with electronic control) there may be hidden difficulties. For example, the need to reconfigure the opening sensor or the risk of damage to the sealing rubber. In this article we will analyze the process step by step - from preparing the tools to the final adjustment - and also tell you which Pozis models require mandatory flashing of the controller after changing sides opening (this applies to lines with a display released after 2021).

If you have never done such work, do not worry: with the right approach, the task will take no more than 1.5–2 hours. The main thing is not to miss critical points, which are often silent in standard instructions.

Preparation: tools and conditions

Before you start work, make sure that you have everything you need. Unlike furniture hinges, the refrigerator door Pozis is attached to specialized hinges with adjusting bolts, so a regular screwdriver may not be enough.

• 🔧 Tools: Phillips and flathead screwdrivers (preferably magnetic), 10 mm socket wrench, 5 mm hexagon, pliers, construction knife.
• 📦 Consumables: painting tape (for fixing the door), silicone grease for the seal, alcohol wipes for cleaning fasteners.
• 📏 Additionally: tape measure (for checking gaps), level (for vertical adjustment), assistant (the door is heavier than it seems!).

Please note: in models Pozis with the system No Frost (for example, RK-139 or RK-167) after re-hanging the door may be required reinstallation of air ducts. This is due to a change in the direction of cold air circulation. If you ignore this point, the refrigerator will work less efficiently, and ice may appear on the back wall.

⚠️ Attention: If your refrigerator Pozis is equipped with display or touch panelbe sure to disconnect it from the network before starting work. 10–15 minutes. This will reset the controller and prevent failures after repositioning the door. In models with a Wi-Fi module (for example, Pozis Smart RK-180), you may need to reconnect to the network.

Also note that in refrigerators with two compressors (linear Pozis Dual Cooling) overhanging the freezer door may affect the operation of the system Super Freeze. After completing the work, check whether the fast freezing settings have been lost.

Step 1: Removing the old door

Start by removing all products and shelves from the door. Even a small weight can deform the hinges when removed. Then seal the door with masking tape in several places - this will prevent it from accidentally falling. In models Pozis the door is attached to three hinges: two lower and one upper (in some modifications - vice versa).

Dismantling algorithm:

1. Remove the decorative plugs from hinges (pry them off with a flat-head screwdriver).
2. Unscrew the bolts of the upper hinge (usually 2-3 pieces) and carefully lift the door, sliding it up.
3. Make sure that the door “comes off” freely from the lower hinges. If it gets stuck, check to see if the rubber seal is in the way.
4. Remove the door and place it on a soft surface (for example, a blanket) to avoid damaging the covering.

In models with hidden hinges (for example, Pozis RK-120), the bolts may be hidden under decorative panel. To remove it, pull the panel towards you - it is held in place by latches. Be careful: plastic is fragile, especially in refrigerators older than 5 years.

⚠️ Attention: If you hear a crunching or crackling sound when removing the door, stop immediately work. This could mean the hinges are warped or the bolts are too tight. In this case, it is better to contact a service center, since continuing on your own can lead to damage to the fasteners.

Step 2: Transferring the hinges to the other side

Now you need to move the hinges to the opposite side. In refrigerators Pozis for this purpose, symmetrical holes are provided, closed with plugs. However, there are important nuances:

• 🔄 In models with electronically controlled (for example, Pozis RK-155) there may be door opening sensor wires under the plugs. They need to be carefully moved without bending.
• 🔧 The hinge bolts often have different lengths - remember which ones were screwed in where, or mark them with tape.
• 📐 Before installing the hinges, check their position with a level. Even a slight misalignment will lead to a loose fit of the door and cold leakage.

Transfer instructions:

1. Remove the plugs on the opposite side of the body (they are usually fixed with latches or glue).
2. Transfer the hinges by screwing the bolts into the new holes. Start with the lower loops - they bear the main load.
3. In models with with a magnetic seal (for example, Pozis RK-170), check whether the magnetic tape does not interfere with the new position of the loops. If necessary, carefully bend it.
4. Install the top hinge, but do not tighten the bolts to the end - you will do this after hanging the door.

Pay special attention Adjusting bolts on the hinges. In refrigerators Pozis they allow you to adjust the position of the door vertically and horizontally. If you tighten them, the door will open on its own; if you don't tighten it enough, a gap will appear.

Step 3: Installing the door in a new place

Hanging the door is the most critical step. Here it is important not only to “catch” the loops correctly, but also to avoid distortions. Start with the bottom hinges:

1. Lift the door and carefully slide it onto the bottom hinge pins. Make sure that it sits evenly, without distortions.
2. Lower the door all the way so that the top hinge aligns with the fastening.
3. Tighten the bolts of the top hinge, but not all the way - the door should “play” a little for adjustment.
4. Check how the door opens and closes. If it clings to the body, loosen the bolts and adjust the position.

In models with French door (for example, Pozis RK-200) the process is complicated by the need to synchronize both leaves. Here you cannot do without an assistant: one person holds the main door, and the second holds the upper leaf.

After preliminary installation, check gaps along the perimeter of the door. They should be the same (1–2 mm). If there is a larger gap on one side, loosen the hinge bolts on the opposite side and adjust the position of the door.

What to do if the door does not close tightly?

If after installation the door does not fit tightly, the reasons may be as follows:

1. Skewed hinges - loosen the bolts and level the door.

2. Deformation of the sealing rubber - warm it with a hairdryer (temperature 50–60°C) and stretch it in problem areas.

3. The sensor wires are in the way - check their location and move them if necessary.

4. Magnets are not transferred correctly (in models with a magnetic seal) - remove the door and reinstall the magnetic tape.

Step 4: Adjusting and checking the tightness

Even if the door is visually level, this does not guarantee its tightness. To check, use test with a sheet of paper:

1. Insert a sheet of paper between the seal and the refrigerator body.
2. Close the door and try to pull out the sheet. If it comes out without effort, the seal does not fit.
3. Repeat the test along the entire perimeter of the door.

If the sheet comes out easily, follow these steps:

• 🔧 Adjust the hinges: loosen the bolts and slightly move the door in the desired direction.
• 🔥 Warm up the seal with a hairdryer (no higher than 60°C!) and stretch it in places where there is a loose fit.
• 🧴 Apply silicone grease to the rubber - this will restore its elasticity.

In refrigerators Pozis s electronic display after re-hanging the door, an error may appear E1 or E2. This means that the opening sensor does not work. To fix the problem:

1. Disconnect the refrigerator from the power supply for 5 minutes.
2. Check the position of the sensor (it should be opposite the magnet in the seal).
3. If the error persists, reset the settings to factory settings (instructions in the manual user).

Step 5: Features for models with electronic control

Refrigerators Pozis with a display or touch panel (series Smart i Premium) require additional manipulations after re-hanging the door. In them, the opening sensor is connected to the control system, and its transfer can disrupt the settings.

What needs to be done:

• 📱 Reflashing the controller: In models Pozis RK-180 and newer, after changing the opening side, you need to update the firmware. This can be done through the official application Pozis Smart or at the service center.
• 🔄 Calibration of sensors: Go to the engineering menu (usually hold down the buttons Super Cool + Light for 5 seconds) and select item Door Calibration.
• 🔌 Checking the Wi-Fi module: If the refrigerator is connected to the network, after moving the door you may need to re-authorize in the application.

In models with voice control (for example, Pozis RK-190) after reversing the door, the microphone setting may be lost. To restore it, reset the voice settings in the menu Settings → Voice Control → Reset.

⚠️ Attention: If after flashing the refrigerator gives an error E4, this means that the controller does not recognize the new position of the sensor. In this case, contact the service center - independent intervention in the firmware can lead to damage to the board.

Also keep in mind that in refrigerators with with the camera inside (for example, Pozis RK-200 Vision) after reversing the door, the viewing angle may change. In this case, you will need to reconfigure the camera position through the engineering menu.

Common errors and how to avoid them

Even if you follow the instructions, you can make mistakes that will lead to incorrect operation of the refrigerator. Here are the most common of them:

• 🚫 Tightening the hinge bolts: This leads to door deformation or broken fasteners. Tighten the bolts with a force of no more than 2–3 Nm.
• 🚫 Ignoring the sensor wire: In models with electronic control, a forgotten or pinched wire can cause a permanent error E1.
• 🚫 Incorrect installation of the magnetic tape: In refrigerators with a magnetic seal (for example, Pozis RK-167), the tape must be strictly parallel to the body.
• 🚫 Lack of adjustment after installation: Even a perfectly installed door can sag over time. Check the tightness once every 3 months.

If, after hanging the door, the refrigerator began to operate louder, check:

• Whether the door touches the housing when opening/closing (this may cause vibration).
• Have the hinge bolts become loose (this can cause the door to rattle).
• Has the compressor shifted (in rare cases, when the door is skewed, vibration is transmitted to it).

In models with inverter compressor (for example, Pozis RK-149W) after re-hanging the door, the noise may temporarily increase. This is normal - the compressor adapts to the new load distribution. If the noise does not disappear after 2-3 days, check the fastening of the compressor.

FAQ: Answers to popular questions

Is it possible to hang the door on a Pozis refrigerator yourself if you have no experience?

Yes, but only if your model does not belong to the series Smart or Premium with electronic control. In classic refrigerators (for example Pozis RK-102 or RK-139) the process is no more complicated than replacing a hinge on a furniture door. The main thing is to follow the instructions and take your time. If in doubt, practice removing and installing the door without re-hanging it.

Is it necessary to change the rubber seal after moving the door?

Not necessary, but in some cases it is recommended. If the seal is older than 5 years or has lost elasticity, it is better to replace it with a new one. In models Pozis with magnetic tape (for example, RK-167) after hanging the door, the elastic band may become deformed. Warm it up with a hairdryer and stretch it - this will help restore its shape. If the seal is torn or cracked, replacement is inevitable.

What to do if, after hanging the door, the refrigerator does not cool?

The reason may be incorrect settings or impaired air circulation. Check:

1. Are the air ducts pinched (relevant for models with No Frost).
2. If the temperature settings are lost (in electronic models a reset may be required).
3. Does the door close tightly - if there is a gap, the compressor will run idle.

If the problem remains, turn off the refrigerator for 1 hour, then turn it on again. In 90% of cases, this helps.

How much does it cost to rehang the door at the service center?

The cost depends on the model and region: On average:

• For classic models (RK-102, RK-110) — 1500–2500 rubles.
• For refrigerators with No Frost (RK-139, RK-149W) — 2500–3500 rubles.
• For Smart models (RK-180, RK-190) — 3500–5000 rubles (including flashing).

If the refrigerator is under warranty, the service may be free - check with the official service Pozis.

Is it possible to hang the door on the freezer separately from the refrigerator?

Yes, but this more difficult. In two-compartment refrigerators Pozis the freezer compartment often has separate hinges, but its door is heavier and requires more precise adjustment. In models with with one compressor (for example, RK-120), overhanging the freezer door can affect the operation of the refrigerator compartment - check the temperature after completion of work.