Re-hanging the doors of the Bosch refrigerator: instructions with photos, diagrams and life hacks

Rearranging the doors on the refrigerator Bosch is a task that almost every owner faces sooner or later. The reasons can be different: moving to a new place where the kitchen layout requires opening in the other direction, broken hinges, or simply a desire to update the interior. Fortunately, most models Bosch (from budget KGN33VW20R to premium KAN92VI30R) provide the ability to rehang doors without contacting a service center.

In this article you will find not just general instructions, but step-by-step guide taking into account design features different series of refrigerators Bosch. We'll look at what tools you'll need, how to properly remove and install the hinges, avoiding common mistakes (for example, warping the door or damaging the seal), and also give advice on setting it up after rehanging. We will pay special attention to models with display on the door and systems NoFrostwhere the process has its own nuances.

If you have never done such work, do not worry. With the right approach, re-hanging the doors will take no more than 1–1.5 hours, and all the necessary parts (plugs, fasteners) are usually included with the refrigerator. The main thing is to follow the instructions and take your time.

Preparation: tools and working conditions

Before you start re-hanging, make sure that you have everything you need. Most tools can be found in the home arsenal, but some (for example, hex keys) may require purchase.

• 🔧 Screwdrivers: cross (PH2) and flat (3-4 mm). For modern models Bosch often you need a screwdriver with a magnetic tip so as not to lose small screws.
• 🔩 Hex key: usually 5 mm in size (for hinges and door fastenings). Some models (for example KIV38X60) use 4 or 6 mm keys.
• 📏 Level: bubble or laser to check the vertical position of the door after installation. Even a slight misalignment can lead to loose closure.
• 🧲 Magnet or telescopic grip: will help to remove fallen screws from hard-to-reach places (for example, under the refrigerator).
• 🧴 Silicone grease: for processing hinges after hanging (prevents squeaking). Any food-grade lubricant will do, for example WD-40 Specialist Food Grade.
• 📦 Set of plugs: usually comes in a box with the refrigerator. If you lost it, you can order original ones from the dealer Bosch by article number (for example, 00643436 for series 6 models).

Also prepare the work space:

• 🚪 Get access: move the refrigerator away from the wall by 50–60 cm, so that it is convenient to work with loops. If the model is built-in (for example Bosch KUL15A50), dismantle the facade.
• 🔌 Turn off the power: unplug from the outlet and wait until the refrigerator is completely defrosted (if required). This will eliminate the risk of a short circuit when working with metal parts.
• 🧊 Remove food: move them to a cooler bag or other cool place. After rehanging, the doors will need to be left open for 1–2 hours for the seal to “get used to.”

⚠️ Attention: If your refrigerator Bosch is equipped with a system VitaFresh with electronic control (for example, models KGN36XL30R or KAN58A50), before rehanging, be sure to take a photo of the location of the wires and connectors on the door. Accidental damage to them can damage the display or temperature sensors.

Weighing schemes for different Bosch models

The design of the hinges and the method of fastening the doors depends on the series of the refrigerator. Below are typical diagrams for popular lines. If your model is not indicated, be guided by the visual similarity of the hinges.

To accurately determine the type of hinges, inspect them from the side: if the fastening screws are visible from the outside, this is a standard pattern. If the screws are not visible, and the hinge is covered with a decorative cover, it will need to be removed (usually it is fixed with latches or one screw from the bottom).

In refrigerators Bosch Serie 8 with a system Home Connect (for example, KAN92VI30R) after rehanging the doors, it is necessary to reprogram opening sensor in the service menu. Otherwise, the display will constantly show an error E:24 (incorrect door position).

How to enter the Bosch Serie 8 service menu?

To reset the error E:24 after rehanging the doors, press and hold the button for 5 seconds SuperCool + SuperFreeze. Then enter the code 1964 (for 2020–2023 models). In the menu, select the item Door Config and confirm the new position of the door.

Step-by-step instructions: removing the old hinges

Start with the top hinge - it is usually easier to dismantle. Important: do not try to remove the door from two hinges at once, otherwise it may fall and damage the seal or frame.

1. Remove the decorative plugs. They cover the mounting screws and are usually secured with latches. Pry them out from the side with a flathead screwdriver (do not use force to avoid breaking the plastic). In models Serie 4/6 the plugs can be glued - gently heat them with a hair dryer.

2. Unscrew the screws of the top hinge. In most cases, these are 2-3 screws for a Phillips screwdriver or hexagon. Hold the door with your hand, as after unscrewing the last screw it may move.

3. Remove the door from the top hinge. Lift it up 1-2 cm and pull it towards you. If the door does not budge, check whether a screw or fastener has gone unnoticed.

4. Disconnect the lower hinge. A ​​hex key may be required here. In models with NoFrost (for example, KGN36XL30R), the lower hinge often has an adjusting bolt - remember its position in order to return the setting later.

After removing the door, inspect the hinges for wear. If there is play or rust on the hinges, replace them (original hinges for Bosch can be found by article numbers 00643435 (upper) and 00643436 (lower)).

⚠️ Attention: In refrigerators Bosch c French door (models KAN58A50, KAN92VI30R), first the upper part of the door is removed, then the lower freezer. An attempt to remove them at the same time will lead to damage to the synchronizing mechanism.

Installing hinges on the opposite side

Now we move on to the most important stage - installing hinges on the new side. It is important to follow the sequence here and not overtighten the screws so as not to damage the threads.

1. Move the plugs. Install plastic plugs on the holes from the old hinges (they usually come with the refrigerator). If the plugs are lost, use similar in size (for example, furniture plugs with a diameter of 8–10 mm).

2. Install the lower hinge. Insert it into the grooves on the opposite side and secure with screws. In models with height adjustment (for example KIN86AF30R), first tighten the screws not completely, then adjust the door position according to the level.

3. Secure the top hinge. Place the door on the lower hinge, align it vertically and fix the upper hinge. Do not tighten the screws completely - first check how the door opens/closes.

4. Adjust the position of the door. Use a level to check the vertical position. If the door sags, tighten the screws on the top hinge. If the body catches, loosen the lower hinge and adjust its height.

For models with display on the door (Bosch Serie 6/8) after installing the hinges you must:

1. Carefully lay the wires into the channels on the new side (use plastic ties to secure them).
2. Connect the connectors to the control board (their location should coincide with the photo taken before dismantling).
3. Check the operation of the display and sensors. If an error appears on the screen E:24 —reset as described in the spoiler above.

After installation is complete, apply a small amount of silicone grease to the hinge hinges - this will prevent creaking when opening.

Adjustment and checking after rehanging

Even if at first glance the door is level, be sure to perform several checks to avoid problems in the future:

• 📐 Checking the level: Apply the level to the side surface of the door. The permissible skew is no more than 1–2 mm. If more, adjust the hinges.
• 🧲 Magnetic fit test: take a sheet of paper and clamp it between the seal and the body. If the sheet is pulled out without effort, the seal needs to be adjusted.
• 🔊 Check for squeaking: open and close the door several times. Extraneous sounds indicate a lack of lubrication or misalignment of the hinges.
• ❄️ Tightness test: Plug in the refrigerator and wait until it reaches temperature. If condensation forms on the walls, the seal allows air to pass through.

To adjust the door, use the following methods:

• If the door sags: tighten the screws top hinge or slightly lift the bottom hinge.
• If the door catches the body: loosen the screws on bottom hinge and move it back a little.
• If the seal does not fit tightly: heat it with a hairdryer (temperature 40–50°C) and press the door for 10–15 minutes. As a last resort, replace the seal (the original one for Bosch has the article number 00643437).

In refrigerators with a system NoFrost after rehanging the doors, cooling may temporarily deteriorate. This is normal: the system needs 12–24 hours to adapt to the new position of the sensors. If after 24 hours the temperature has not returned to normal, check whether the sensor wires are pinched.

⚠️ Attention: In models Bosch with the function SuperCooling (for example, KAN92VI30R) after reversing the doors it may the protection against incorrect installation will trigger. To reset it, press and hold the button SuperCooling 10 seconds until the sound signal.

Frequent errors and how to avoid them

Even if you carefully follow the instructions, you can make mistakes that will lead to incorrect operation of the refrigerator. Here are the most common ones and how to eliminate them:

Pay special attention to models with inverter compressor (for example, Bosch KIN86VF30R). After re-hanging the doors, the compressor may start working at increased power, trying to compensate for the loss of cold. If after 24 hours the noise has not returned to normal, check whether the refrigerant pipes are pinched when installing the hinges.

Another typical problem is displacement of the shelf holders on the door. In some models (for example, KAD92SB30R) the shelf holders are fixed on special guides, which must be moved to the other side when re-hanging. If this is not done, the shelves will hang or fall. opening.

How to move the shelf holders to the other side?

In models Bosch Serie 4/6 the shelf holders are mounted on symmetrical grooves To move them:

1. Remove the shelves from their holders.

2. Press the holder lock from the bottom and slide it up.

3. Move the holder to the opposite groove and fix it until it clicks.

4. Return the shelves to their place. data-i="239">Reversing doors in Bosch refrigerators with a display

Reversing doors on Bosch refrigerators with display

Electronically controlled models (Bosch Serie 6/8, Home Connect) require a special approach due to the presence of wires connecting the door to the main unit. Here it is important not only to mechanically re-hang the door, but also to reposition the cables correctly.

Algorithm. steps:

1. Disconnect the connectors. Carefully disconnect all wires from the board on the door (usually these are connectors for the display, opening sensor and backlight). Remember or photograph their location.

2. Move the wires to the channels on the other side. In the doors Bosch special plastic channels are provided for this. Use plastic ties to secure the wires and avoid bending them.

3. Connect the connectors on the new side. Make sure that all connections are tight. If the connector does not lock, check whether its contact is bent (you can carefully straighten it with a thin wire). screwdriver).

4. Reset the settings. After reversing, an error may appear on the display. To reset it, enter the service menu (see spoiler above) and select the item Door Config.

On models with Wi-Fi module (for example, KAN92VI30R) after re-connection, you may need to reconnect to the network. To do this:

1. Press the button Home Connect to 5 seconds.
2. In the mobile application Bosch Home Connect select "Add device".
3. Follow the instructions on the screen (usually you need to enter the PIN code from the sticker on the back wall of the refrigerator).

⚠️ Attention: If after re-hanging the doors of the refrigerator Bosch with the display stopped responding to button presses, check whether the main power cable of the display is pinched (it comes from the bottom hinge). In this case, you will have to remove the door again and lay the wire correctly.

FAQ: answers to frequently asked questions

Is it possible to rehang the doors on a Bosch refrigerator yourself if you have no experience?

Yes, this is quite possible even for a beginner. The main thing is to follow the instructions, take your time and prepare all the tools in advance. The most difficult part is working with wires in models with a display, but if you take a photo before dismantling, there will be no problems. On average, the process takes 1–1.5 hours. data-i="267">What to do if, after rehanging, the Bosch refrigerator door does not close tightly?

What should I do if, after rehanging, the Bosch refrigerator door does not close tightly?

First, check if the refrigerator is level (use a level). Then adjust the hinges: if the door sags, tighten the top hinge; if the body catches, loosen the bottom one and move it back a little. Also check the seal: it may have become deformed when removed. Warm it up with a hairdryer (temperature 40–50°C) and press the door for 10–15 minutes.

Do you need to defrost the refrigerator before rehanging the doors?

Absolutely! Even if you have a model with NoFrost, before work you need to unplug the refrigerator and wait until it is completely defrosted. This is due to two reasons: firstly, condensation on parts can lead to corrosion of the hinges; secondly, ice in the freezer will add weight to the door, which will complicate its removal.

Where can I get plugs for the holes after rehanging the doors?

The plugs usually come with the refrigerator (in the package with documentation). If they are not available, you can order original ones from the dealer Bosch (article 00643436) or use universal furniture plugs with a diameter of 8–10 mm. As a last resort, the holes can be covered with decorative tape, but this is a temporary solution.

Error E:24 appeared after rehanging the doors on the Bosch Serie 8 refrigerator. How to fix it?

The error E:24 means that the system recognized the incorrect position of the door. To reset it:

1. Press and hold the buttons SuperCool + SuperFreeze 5 seconds.
2. Enter the code 1964 (for models 2020–2023).
3. In the service menu, select item Door Config and confirm the new position of the door.

If the error remains, check whether the door sensor wires are connected correctly.