Reversing the doors on a Veko refrigerator: instructions with photos and expert advice

If your refrigerator is under warranty, check the conditions of the service center: some dealers Veko the warranty will be void if you tamper with the design yourself. For models with a display (for example Veko RCN 3302 X), additional adjustment of the sensors may be required after changing the door position.

Preparation: tools and conditions

Before starting work, make sure that you have everything you need. For most models Veko you will need:

• ✅ Phillips screwdriver (PH2) - for hinge screws and decorative panels.
• ✅ Hex key (4 mm) - for some models with lower door fastening.
• ✅ Plastic spatula or mediator - to carefully remove decorative trims.
• ✅ Masking tape - to secure the door during the rearrangement process.
• ✅ Level (optional) - to check the horizontal position after installation.

Important: if your refrigerator is equipped system No Frost (for example, Veko KFN 1601 W), before work, disconnect it from the network for 1-2 hours. This will prevent the fan from accidentally turning on when the door is open, which can lead to icing of the evaporator.

Work in a well-lit area. If the refrigerator is in a niche, pull it out 50–60 cm for easy access to the hinges. Place cardboard or soft cloth under the legs to avoid scratching the floor.

Removing the door: step-by-step process

The algorithm for dismantling the door depends on the model. Below is a universal instruction suitable for most refrigerators Veko 2018–2026. For older models (before 2015), a different approach may be required - see section on outdated series.

1. Unplug the refrigerator from the network and make sure that there are no fragile products inside (glass jars, eggs).
2. Remove the decorative covers from the hinges. To do this, pry them off with a plastic spatula from the side (not from above!). In models Veko GSN the covers can be attached with latches - pull them towards you with force.
3. Unscrew the screws of the top hinge (usually 2-3 pieces). Hold the door so that it does not fall after loosening the fastening.
4. Remove the door from the lower hinge, lifting it up at an angle of 30–40°. If the door is "jammed", check whether the seal is in the way - it can be temporarily bent.

Critical point: in refrigerators Veko s French Door (two-door models, for example RCN 5201 X) First, the upper small door is removed, and then the lower large one. An attempt to dismantle them at the same time will lead to damage to the guides.

Make sure that the refrigerator is unplugged from the mains|

Secure the door with masking tape to avoid falling|

Prepare a place for laying the door (soft surface)|

Check the presence of all tools

-->

Transfer of hinges and fasteners

After removing the door, holes from the hinges remain on the refrigerator body. Most models Veko provide symmetrical fastenings for hanging, but sometimes it is necessary rearranging the plugs or drilling new holes.

Inspect the opposite side of the refrigerator:

• ✅ If there are factory holes for hinges (usually closed with plastic plugs), use them.
• ✅ If there are no holes, you will have to drill. To do this:
1. Attach the loop to the attachment point and mark the centers of future holes with a pencil.
2. Use a drill with a diameter of 4–5 mm (for most models Veko).
3. Cover the internal shelves with film so that metal shavings do not get into the cooling system.

Attention! In refrigerators with inverter compressor (series Inverter Pro), do not drill holes closer than 5 cm to the back wall - refrigerant tubes pass there. Damage to the tube will lead to freon leakage and expensive repairs.

Veko model	Hinge type	Do I need to drill?	Features
RCN 3301 W	Removable, 3 screw	No (there are symmetrical holes)	Decorative overlays are fragile - remove carefully
KFN 1602 X	Fixed, 2 screws + latch	Yes (only for the lower hinge)	The upper hinge is universal, the lower one requires relocation
GSN 5101	Hidden, 4 screws	No	The hinges are hidden under the top panel - you need a screwdriver with a long blade

What to do if are the hinges not symmetrical?

In some models Veko (for example, RCN 2201) the hinges are not interchangeable - the left and right ones have different shapes. In this case you will have to:

1. Order a mirror hinge from an authorized dealer. (the article number is usually indicated in the instructions).

2. Use universal hinges from third-party manufacturers (suitable for 80% of refrigerators Veko).

3. Turn over existing hinges, if their design allows this (check for holes on both sides).

Installing the door in a new position

Before installing the door on the opposite side check. sealIn refrigerators Veko it often has an asymmetrical profile - one side is thicker for a tight fit. If the seal is hard or deformed, it will have to be turned over or replaced.

Installation sequence:

1. Place the door on lower hingealigning it with level.
2. Secure top hinge, but do not tighten the screws all the way - the door should “play” a little.
3. Check the gaps around the perimeter: they should be the same (1-2 mm) if one side fits tighter, loosen the hinge and adjust the position.
4. Install the decorative trims, making sure they do not interfere with the closure.

Tip: if the door closes with force after installation, lubricate the seal with silicone grease (not Vaseline!) In models with electronically controlled (for example, Veko RCN 3302 X) after rehanging. an error may occur E1 (loose closure). To reset it, hold the button Super Cool 5 seconds.

Removable (3 screw)|

Fixed (with latches)|

Hidden (under the panel)|

I don’t know

-->

Adjustment and checking

After installing the door be sure to adjust its position. In refrigerators Veko this is done using:

• ⚙️ Upper hinge — adjusts the tilt of the door (if it tilts forward/backward).
• ⚙️ Lower hinge —responsible for the vertical position (if the door sags).
• ⚙️ Middle bracket (available in models with a height >180 cm) - corrects the horizontal.

To check:

1. Place a sheet of paper between the seal and the body around the entire perimeter.
2. Close the door and try to pull out the sheet. Optimal resistance —the sheet comes out with a slight effort.
3. If the sheet falls out on its own or not pulls out - adjust the hinges.

Criteria for successful rearrangement: the door closes with a slight push (without slamming), and the seal does not deform. In models with display after adjustment, calibration of the closing sensor may be required (see instructions for the specific model).

Frequent errors and how to avoid them

Even with careful work, owners Veko face typical problems. Here are the most common:

• 🔧 Door skew —occurs if the hinges are not leveled. Solution: loosen all the screws, level the door and tighten the fastenings crosswise.
• 💧 Condensation on the seal — means that the door does not fit tightly. Solution: check the seal for deformation, if necessary, warm it with a hairdryer (temperature no higher than 50°C).
• 🔊 Creak when opening —usually caused by friction of the hinges. Solution: lubricate the hinges with silicone grease (not oil!).
• ⚡ Error on the display (for example, E2) - appears in models with a closure sensor. Solution: reset the error according to the instructions or turn off the refrigerator for 10 minutes.

Attention! If, after re-hanging, the refrigerator begins to cool worse, check Are the refrigerant pipes behind the door pinched? In models Veko with a system Multi Air Flow (for example, RCN 4001), pinching the air ducts can lead to freezing of the evaporator.

Another common mistake is ignoring door weights. In refrigerators with French Door the upper door is lighter than the lower one, and if the hinges are mixed up, the lower door will sag. In this case, it will be necessary to replace the hinges with reinforced ones.

Features for old models (before 2015)

Which models are considered “old”?

We classify them as “obsolete” refrigerators Veko, released before 2015, including the series:

- RC (single-chamber),

- KN (with mechanical control),

- GS (without No Frost system).

These models have metal hinges without plastic linings and often require drilling new holes.

Refrigerators Veko manufactured before 2015 have fundamental differences:

• 🔩 Metal hinges, without decorative trims - unscrew with a 10 mm wrench.
• 🔧 There are no symmetrical holes - you will have to drill new ones.
• 📏 The seal is glued, not inserted into the groove - when rehanging it, you need to carefully separate it and re-glue it.

For these models:

1. Remove the door, as described above, but keep in mind that the screws may be rusty - use penetrating lubricant.
2. Move the hinges to the opposite side, having previously marked the holes through a template (can be made of cardboard).
3. When drilling, use a metal drill - the body of the old ones Veko is thicker than for new models.
4. After re-gluing, press the seal with a load (for example, books) for 12 hours.

Attention! In old models with drip system (without No Frost) after rehanging the door, the direction of condensate drainage may change. Check that the drainage hole remains at the bottom - otherwise water will accumulate at the bottom of the chamber.

FAQ: answers to frequently asked questions

Is it possible to hang the door on a Veko refrigerator with a display (for example, RCN 3302 X) independently?

Yes, but after rearrangement it may be required resetting the closing sensor. To do this:

1. Disconnect the refrigerator from the power supply for 1 minute.
2. Turn on and hold the button Super Cool 5 seconds until the signal sounds.
3. If error E1 remains - repeat the procedure or contact service.

In models with touch controls (for example, Veko Inverter Pro), flashing may be required if the door was hung incorrectly.

What to do if the door does not close after rehanging tight?
Causes and solutions:
• The seal is deformed → Warm it with a hairdryer (max. 50°C) and level it with your hands.
• The hinges are tightened unevenly → Loosen all screws, level the door and tighten crosswise.
• The refrigerator body is deformed → Check the levelness of the floor - if the refrigerator is on a slope, the door will be skewed.
Do I need to rehang both doors in a Veko two-chamber refrigerator?
No, not necessarily. In models like French Door (for example, Veko RCN 5201 X), you can hang only the upper or only the lower door. However, keep in mind:
• If you only re-hang the top door, the bottom one may rest against it when opened.
• In refrigerators with with one compressor (most Veko), re-hanging one door does not affect the operation of the other.
How to rehang a door if the hinges are rusty and cannot be unscrewed?

Action algorithm:

1. Treat the screws with penetrating lubricant (WD-40, Liqui Moli) and wait 15-20 minutes.
2. Use an impact screwdriver or a wrench with a lever, but without excessive force.
3. If the screw breaks, drill it with a metal drill (diameter 0.5 mm less than the thread) and cut a new thread with a tap.
4. For older models Veko you can find a hinge repair kit (the article usually starts with VK-).

Attention! Do not use a grinder to cut screws - sparks can damage the paint of the case.

How much does it cost to rehang a door at the Veko service center?

The cost of the service depends on the model and region:

• Single-chamber refrigerators (for example, Veko GSN 3101) - from 1,500 to 2,500 rubles.
• Double-chamber (for example, Veko RCN 3302 X) - from 2,500 to 3,500 rubles.
• Models with French Door - from 4 000 rubles (due to the complexity of adjusting two doors).

The price usually includes:

• Dismantling/installation of the door.
• Adjusting the hinges.
• Diagnostics of the seal.

Additionally the following may be paid for:

• Replacement of hinges (from 800 rubles per piece).
• Replacement of the seal (from 1,200 rubles).

⚠️ Check the price in the official service Veko —tariffs may vary depending on the dealer's policy.