We rehang the Bosch refrigerator door yourself: instructions with photos and videos

In this article we will analyze the process using the example of popular series KIN86, KAN92, KAD90 and other two-chamber models with the system NoFrost. We will pay special attention to the nuances for refrigerators with a display, an ice maker and models with a French door. If yours Bosch was released after 2018, the instructions are 100% current - the design of the hinges has not changed. For older devices (before 2015), additional parts may be required, which we will also mention.

⚠️ Attention: Rearranging the doors will void the warranty if the refrigerator is under warranty service. Check the deadline in the documents or through the service Bosch Home Connect before starting work.

1. Preparation: tools and conditions

Before you begin, make sure that you have everything you need. Bosch supplies with the refrigerator special plugs for the holes for the hinges - they must be used when rearranging. If they are lost, order the original ones through the service center (the article depends on the model, for example, 00642439 for the series KIN86).

List of tools:

• 🔧 Phillips screwdriver (preferably magnetic, so as not to lose the screws)
• 🔨 Hex key 5 mm (for some models). space:
• 📏 Level (to check horizontality after installation)
• 🧲 Magnet or telescopic grip for screws
• 🧴 Silicone grease (for hinges after rearrangement)

Also prepare your workspace:

• 🚪 Clear a passage at least 1.5 m wide around the refrigerator.
• 🧊 Remove all food and turn off the power (at least 2 hours to allow the seal to defrost).
• 📦 Remove shelves from doors and put them in a safe place place.
• 🧹 Place a soft cloth or cardboard under the door in case of a fall.

⚠️ Attention: If your refrigerator is equipped with a system Home Connect or display on the door, after rearranging, you may need to reconnect the Wi-Fi module. Take a photo of the location of the wires in advance!

2. Door fastening diagram: what to rearrange and where

Design of doors Bosch symmetrical, but there are important details:

• 🔄 Upper loop - universal, rearranged in a mirror way.
• 🔄 Bottom hinge - often has a left/right version (marks L/R on the body).
• 🔄 Decorative panels - fastened with latches, when rearranged they change places.
• 🔄 Sealant - do not require replacement, but it must be cleaned and lubricated after work.

Below is a table with the location of holes for popular series:

For models with ice maker (for example, KAN94VI35) you will additionally need:

• 💧 Rearrange the water supply tube (included with the refrigerator).
• 🔌 Reconfigure the door opening sensor (instructions in the section 5).

3. Step-by-step instructions: removing the old hinges

Start with the top hinge - it is easier to dismantle. Important: for models with a display, first turn off the power and remove the protective cover from the wires (it is attached to latches).

Action algorithm:

1. Open the refrigerator door 90°. Support it with a chair or an assistant.
2. Remove the decorative panel from the top hinge (pull it up or pry it with a screwdriver).
3. Unscrew the screws securing the hinge to the body (usually 3 pieces). Hold the door!
4. Carefully remove the door from the bottom hinge, lifting it up.
5. Remove the bottom panel and unscrew the screws of the bottom hinge.

⚠️ Attention: U models KAD90 i KAD92 an opening sensor is hidden in the bottom hinge. Do not pull the wires - first disconnect the connector!

If the door is “jammed” when removing, do not apply force. Most likely, the seal is in the way - carefully bend it around the perimeter. For models with French Door (double-leaf freezer), first remove the upper small door, then the large one.

4. Installing hinges on the new side: nuances and errors

Now you need to transfer the hinges to the opposite side. The main thing here is not to confuse the upper and lower hinges (they are marked) and to position the decorative panels correctly.

Work order:

1. Install the bottom hinge on the new side using the standard holes. Tighten the screws not completely.
2. Place the door on the bottom hinge, level it.
3. Tighten the top hinge, but do not tighten the screws.
4. Check gaps: the door should open 90° without effort, and the seal should fit evenly.
5. Tighten all screws and install decorative panels.

Typical mistakes and how to avoid them:

• ❌ Door misalignment → Use a level and check the diagonals.
• ❌ Mismatched holes → Make sure you are using the correct plugs (they are of different diameters!).
• ❌ The seal is damaged → Do not pull on it during installation, lubricate it with silicone after installation.
• ❌ The door does not close tightly → Check whether the sensor wire is in the way (relevant for KAD90).

For models with ice maker after installing the hinges:

1. Move the water supply tube to the other side (included).
2. Reconfigure the closing sensor (instructions in the next section).
3. Check the tightness of the connections - leaks can damage the electronics!

5. Setting up sensors and electronics after rearrangement

If your refrigerator is equipped with a display (KAD90VI30, KAN94VI35 etc.), after rearranging the doors you will need to:

1. Reset the error E:24 (if it appears) through the menu Settings → Reset.
2. Reconfigure the door opening sensor:

1. Unplug the refrigerator for 5 minutes.
2. Turn on and immediately press Super Cool + Super Freeze for 5 seconds.
3. Wait for the sound signal - the sensor is calibrated.

For models with Home Connect:

• 📱 Reconnect the refrigerator in the application (section Devices → Settings → Reset connection).
• 🔄 Update the firmware if a notification appears.

⚠️ Attention: If after rearranging the refrigerator Bosch gives an error E:15 (problem with the temperature sensor), check whether the wires under the decorative panel are pinched. This often happens when the top hinge is installed carelessly.

6. Checking the tightness and final steps

After installing the doors, you need to make sure they are working correctly:

1. Check adhesion of the seal - take a sheet of paper, close the door and try to pull it out. efforts, adjustment is required.
2. Measure temperature in cameras after 2 hours of operation Norm: +4°C in the refrigerator and -18°C in the freezer.
3. Listen extraneous noise -creaking or knocking may indicate misalignment of the hinges.

If the seal does not fit tightly:

• 🔧 Loosen hinge screws and adjust the position of the door.
• 🧴 Apply silicone grease to the rubber (do not use vegetable oil!).
• 🔥 Warm the seal with a hairdryer (temperature 50°C) - it will become more elastic.

For models c NoFrost after rearranging the doors, the compressor operating time may temporarily increase - this is normal. The system adapts to new conditions within 24 hours.

1) Door closure tightness (test with a sheet of paper).

2) Location of products - they should not block the ventilation openings.

3) Temperature settings (the mode may have gone wrong after turning off the power).-->

7. Features for different Bosch series

The design of hinges and doors may vary depending on the series. Below are the key nuances:

For refrigerators with French door (two doors on the freezer) process more difficult:

• 🔄 First, the small upper door is rearranged.
• 🔄 Then - the large freezer door (an assistant is required!).
• 🔄 Lastly - the refrigerator camera.

⚠️ Attention: For models Bosch with the system VitaFresh (freshness zone), after rearranging the doors, you may need to re-adjust the humidity. Go to the menu Settings → VitaFresh → Calibrate.

8. solutions

Even with careful rearrangement, difficulties may arise. Let's consider typical cases:

Problem 1: The door does not close tightly.

• 🔹 Check whether the seal is in the way (it may have become deformed during removal).
• 🔹 Adjust the height of the door using the screws on the bottom hinge.
• 🔹 Make sure that the refrigerator is level (use a level).

Problem 2: There is a creaking sound when opening.

• 🔹 Lubricate the hinges with silicone grease (do not use WD-40!).
• 🔹 Check to see if the screws are loose.
• 🔹 If the squeaking persists, the hinge bushing may be damaged - replacement is required.

Problem 3: The refrigerator has become louder.

• 🔹 This is normal in the first day - the system adapts to the new position of the doors.
• 🔹 Check whether the door is touching the housing (it may vibrate during operation compressor).
• 🔹 Make sure the ventilation grilles are not blocked.

Problem 4: The display or ice maker does not work.

• 🔹 Check the wire connections (take a photo of them before dismantling?).
• 🔹 Reset errors through the menu Settings → Reset.
• 🔹 If the problem remains, the connector may be damaged - contact the service.

FAQ: Answers to frequently asked questions