Hanging refrigerator doors Indesit is a task faced by many owners when moving, renovating a kitchen, or simply wanting to change the opening side. Despite the apparent complexity, the procedure is quite doable with your own hands if you know the key nuances of the design and avoid typical mistakes. In this article we will analyze the process step by step, supplement it video instructions in Russian, provide fastening diagrams for popular models and point out the “pitfalls” that are silent about in standard manuals.
Features of refrigerators Indesit (unlike many other brands) - a unified door fastening system on most models of the series C, B i T. This means that the instructions are suitable for devices aged from 5 to 15 years, if their design has not undergone radical changes. However on models with a system No Frost and electronic control (for example, Indesit ITF 118) you may need additional adjustment of the sensors after rehanging —we will also tell you about this.
Before you begin, check the equipment of your refrigerator: The box with the documentation should contain plugs for the holes on the opposite side and, possibly, a special key for adjusting the hinges. If they are not there, no problem, we will tell you what to replace.
Preparation: tools and conditions
To work, you will need a minimum set of tools, but you won’t be able to do without them. Here's what you need to prepare:
- 🔧 Phillips screwdriver (better magnetic so as not to lose the screws)
- 🔨 10 mm wrench (for some models - 8 mm)
- 📏 Level (for checking vertical after installation)
- 🧲 Magnet (to hold the door during operation)
- 🧴 Silicone grease (for hinges if they creak)
Also prepare your work space:
- 🚪 Clear the passage to the refrigerator by at least 1.5 meters - the door will be completely removable.
- 🧊 Unplug the refrigerator 2-3 hours before starting work so that the ice on the freezer melts (if any).
- 📦 Remove all food from door shelves and drawers.
⚠️ Attention: If your refrigerator Indesit is equipped with a display or touch buttons on the door, before removing the door, take a photo of the location of the wires and connectors. On models ITF 118 W i ITF 120 W the wires are attached to the loop with special clips - they can be easily damaged during careless dismantling.
If you have never done such work, look first video with a complete analysis of the process (we will provide links to verified videos below). This will help to visualize the steps and avoid annoying mistakes, for example, mixing up the top and bottom hinges.
Step-by-step instructions: how to remove the Indesit refrigerator door
Let's start by dismantling the old door. This stage is the most critical - it is easy to damage the hinges or seal. Follow the algorithm:
- Remove the decorative plugs from the hinges (they are usually plastic and are pryed off with a screwdriver). The fastening screws are hidden under them.
- Unscrew the top hinge:
- Hold the door with one hand (or fix it with a magnet).
- The screws can be a Phillips screwdriver or a wrench - it depends on models.
- On some refrigerators (for example, Indesit BIAA 13), the top hinge is secured with 3 screws, not 2.
- Lift the door up to remove the pin from the groove.
- If the door is “jammed”, do not pull by force - check that all the screws are unscrewed.
- Carefully place the door on a soft surface (for example, a blanket) so as not to scratch it.
On models with No Frost after removing the door you will see wires going to the opening sensor. They need to be disconnected, remembering the location of the connectors. If the wires are short, do not pull them - it is better to remove the sensor mount from the door body.
☑️ Checklist before removing the door
Now you can start re-hanging the hinges to the other side. But first, check if there are holes for fastenings on the opposite side of the case. If they are not there, you will have to drill (read about this in the next section).
Moving hinges to the other side: nuances for different models
On most refrigerators Indesit the holes for the hinges are symmetrically located on both sides, but are closed with plugs. However, there are exceptions:
- 🔹 Models BIAA 13, BIAA 16 and others like them have ready-made holes - just remove the plugs and screw in the hinges.
- 🔹 On refrigerators of the series C 132 i C 138 may required drill new holes (the template is usually included).
- 🔹 Two-door models (Indesit TIA 18) have additional fastenings for the freezer - they also need to be moved.
If there are no holes, proceed as follows:
- Attach the loop to the attachment point and mark the centers of future holes with a pencil.
- Use a metal drill with a diameter
4–5 mm(for the exact size, see the instructions for the model). - After drilling, remove metal shavings with a vacuum cleaner - they should not get inside the refrigerator.
| Refrigerator model | Type of hinge fastening | Is it necessary drill? | Features |
|---|---|---|---|
| Indesit BIAA 13 | Symmetrical holes | No | Plugs are removed with a screwdriver |
| Indesit C 132 | Partially symmetrical | Yes (2 holes) | Template included |
| Indesit TIA 18 | Separate for cold rooms. and frost. cameras | No | Requires relocation of the opening sensor |
| Indesit ITF 118 | Hidden loops | No | Sensor wires in the loop |
⚠️ Attention: On models with No Frost after reversing the door, an errorF04orF05(sensor malfunction) may occur. This means that the wires are not connected correctly or the sensor has moved. Check their location and, if necessary, reset the error according to the instructions.
After moving the hinges, do not rush to hang the door back. First check:
- 🔧 Are all the screws tightened all the way (but without fanaticism, so as not to break the threads).
- 📐 Do the holes on the door and hinges match (if not, sharpen them with a file).
- 🧲 Attach the magnet to the hinges - it should fit tightly, without play.
Installing the door on a new side: procedure
Now that the hinges have been moved, you can hang the door back. This stage requires care, since the door is heavy, and the hinges must fit perfectly.
- Place the door on the lower hinge:
- Lift the door so that the pin fits into the hinge groove.
- If the door does not sit down, check if the seal is in the way.
- Secure the upper hinge:
- Tighten the screws diagonally to avoid distortion.
- Do not tighten them completely at once - first grab everything lightly, then tighten.
- The door should open smoothly, without creaking.
- The gap between the door and the body on all sides should be the same (
2–3 mm). - Place cardboard under the front legs or rotate them counterclockwise.
- Use a level to check the tilt.
- Plug in the refrigerator.
- Open and close the door 3-4 times in a row.
- If the error on the display does not disappear, refer to the instructions reset errors for your model.
If the door is after installation opens spontaneously, this means that the refrigerator is not level. Adjust the legs so that the body has a slight tilt back (1-2 degrees). For this:
On models with No Frost after installing the door, it may required calibrating the opening sensor. To do this:
Adjusting the door after re-hanging
Even if the door is visually level, it needs to be adjusted for a tight fit. fit. Here's how to do it:
- Check the seal:
- Close the door and run your hand around the perimeter - there should be no drafts.
- If the seal is deformed, warm it with a hair dryer (temperature
50–60°Cand give shape.
- Adjust the hinges:
- Loosen the screws on the hinges and slightly move the door in the desired direction.
- Tighten the screws and check the result.
- Place a sheet of paper between the seal and the body.
- If the sheet is pulled out without effort, additional adjustment is needed.
- Unplug the refrigerator for 5 minutes.
- Plug it back in and wait for the compressor to start.
On models with No Frost after adjustment, you may need rebooting the electronic unitTo do this:
⚠️ Attention: If, after rehanging, the refrigerator begins to buzz or vibrate loudly, check whether the door is touching the internal condenser tubes. This may lead to. damage to the cooling system.
If the adjustment did not help and the door still does not fit tightly, the seal may have worn out. In this case, it needs to be replaced (read more about this in our article “How to change the rubber band on the refrigerator Indesit»).
What to do if the door is re-hanged) creaks?
The creaking usually occurs due to a lack of lubrication in the hinges or misalignment. Lubricate the hinges with silicone grease (do not use WD-40 - it will corrode the plastic!). If the squeak remains, check whether the door is rubbing against the body. In extreme cases, you can loosen the hinge screws a little, but do not overdo it, otherwise the door will sag.
Video instructions in Russian
For clarity, we have selected proven videos with a step-by-step analysis of the process of hanging doors on refrigerators Indesit. Pay attention to models similar to yours:
- 📺 Indesit BIAA 13 / BIAA 16 - classic model with mechanical control:
- Video: “Re-hanging the door in 15 minutes” (channel Repair of Household Equipment).
- Features: showing the transfer of hinges without drilling, adjustment of the seal.
- 📺 Indesit ITF 118 W (No Frost) —with electronic control:
- Video: “How to hang a door with a sensor” (channel Cold at Home).
- Features: disconnecting the sensor wires is shown in detail.
- 📺 Indesit TIA 18 —two-door model:
- Video: “Re-hanging both doors” (channel MasterPlus).
- Features: separate analysis of freezer fastenings.
If your model is not in the list, look for the video using keywords:
"Indesit [your model] rehang the door" or «Indesit door reversal». Pay attention to the date of publication - the design of refrigerators can change even within the same series.
Before repeating the steps from the video, check our instructions. For example, in some videos the authors do not mention. data-i="223">on models with relocating the opening sensor on models with No Frostwhich can lead to errors in operation.
Frequent errors and how to avoid them
Even when following the instructions, you can make mistakes that lead to breakdowns or incorrect operation refrigerator. Here are the most common:
- 🚫 The upper and lower hinges are mixed up:
- Consequences: the door does not close or is warped.
- Solution: swap the hinges and check the markings (on some models they are marked
«TOP»i«BOTTOM»).
- 🚫 The holes for attaching the handle have not been moved:
- Consequences: the handle interferes with opening or is not fixed.
- Solution: remove the handle and move it to the other side (the holes are usually symmetrical).
- 🚫 The seal is damaged:
- Consequences: the refrigerator does not keep cold, there is ice in the freezer.
- Solution: warm the seal with a hair dryer or replace it.
- 🚫 Not sensor wires are connected (on models with No Frost):
- Consequences: error on the display, the compressor runs without stopping.
- Solution: check the connectors and reset the error according to the instructions.
Another typical problem - the door does not magnetize after rehangingThis happens due to:
- 🔹 Incorrect adjustment of the hinges (you need to loosen the screws and move the door closer to the body).
- 🔹 Deformation of the seal (try warming it up or replacing it).
- 🔹 The refrigerator is skewed (adjust the legs according to the level).
If after all the manipulations the door still does not close tightly, perhaps the problem is worn hingesIn this case, they need to be replaced (parts can be ordered by the refrigerator model number).
FAQ: answering frequently asked questions
Is it possible to hang the door on an Indesit refrigerator yourself if you have no experience?
Yes, the procedure does not require special skills, but it will require accuracy. The main thing is to take your time and follow the instructions. If you have a model with No Frost, pay special attention. on the sensor wires. In difficult cases (for example, if you need to drill new holes), it is better to invite an assistant.
How long does it take to rehang the door?
On average - from 30 minutes to 1.5 hours, depending on the model and the availability of tools. On classic refrigerators (Indesit BIAA 13) it takes less time, on models. c No Frost (Indesit ITF 118) - longer due to the need to work with wires.
Is it necessary to defrost the refrigerator before hanging the door?
It is advisable, especially if there is ice on the freezer compartment. This will make it easier to remove the door and prevent moisture from getting on the electrical contacts. there is no ice, you can do without defrosting.
What to do if the door creaks after rehanging?
The creaking is usually caused by friction of the hinges or misalignment. Lubricate the hinges with silicone grease (do not use oils or WD-40!) If the creaking remains, check whether the door is rubbing against the body and adjust. hinges.
Is it possible to reverse the door on an Indesit refrigerator with a display?
Yes, but on such models (Indesit ITF 118 W, ITF 120 W) you need to carefully disconnect the wires of the display and the opening sensor. It is better to photograph their location before dismantling. After installing the door, check the operation of the display - if it does not turn on, check it. perhaps the contacts are damaged.