The need to change the direction of opening the door refrigerator Biryusa often occurs when remodeling the kitchen or changing the arrangement of furniture. The standard factory configuration assumes opening from right to left, which is not convenient in every room. The rehanging process requires care, but it can be done at home without calling a specialist.
Before starting work, it is important to make sure that the selected opening side is technically possible for your specific model. Some budget versions single-chamber refrigerators may not have symmetrical holes for hinges or handles. Carefully inspect the body and door leaf from all sides.
To perform the operation, you will need a minimum set of tools, which most home craftsmen will have. The main attention should be paid to preparing the work area, since the refrigerator will have to be tilted and its contents must be completely removed. Below is a detailed diagram of actions for the safe and correct reinstallation of awnings.
Necessary tools and preparation of the workspace
Quality preparation is half the success of the entire operation. You don't need complex professional equipment; a standard home craftsman's kit is enough. The main requirement is that the tools must be in good working order and match the type of fastener used in your model Biryusa.
The basic kit includes a slotted and Phillips screwdriver. Often the screws can be quite tight, so it is best to use tools with a comfortable handle. You may also need a socket wrench or 10 mm socket if the hinges are secured with large diameter bolts.
- 🔧 A set of screwdrivers (phillips and flat head) for removing decorative elements.
- 🔩 Socket wrench or wrench (usually 8, 10 mm) for the main bolts loops.
- 🧤 Work gloves to protect hands from sharp edges and grease.
- 📏 Construction level or ruler to check the symmetry of the installation.
Pay special attention freeing up space. Open the doors wide and make sure there is nothing obstructing their full movement. If you plan to remove the door completely, there should be a place nearby where it can be safely placed on a prepared soft surface, such as cardboard or a blanket.
Dismantling the top part and removing the door
The process begins with the top hinge, since it is this that holds the bulk of the door canvases in a suspended state. First you need to remove the decorative plug, which is usually located on top of the case. It can be attached with latches or held in place due to a tight fit.
⚠️ Attention: Before starting work, be sure to disconnect the refrigerator from the power supply! This will protect you and prevent accidental damage to wiring or sensors.
After removing the plug, access to the upper mounting bolts will open. Carefully unscrew them, but do not rush to remove the loop itself. At this stage, you will need an assistant to hold the door. If you are working alone, make sure you can securely lock the position of the cabinet.
The next step is to remove the door from the bottom hinge. Lift the blade up to remove the axle from the bottom hole. Proceed with caution as the weight of the door is significant. Place the removed door on the prepared place with the outer side up so as not to scratch the coating.
☑️ Preparation for dismantling
Rearranging the fittings and handles
The most time-consuming part of the work is moving the fittings to the opposite side. In refrigerators Turk handles are often secured with screws on the inside of the door. You need to unscrew them and install plugs in the vacated holes on the outside.
If the model is equipped with hidden handles or recesses, the procedure is simplified. However, if the handle is removable, check the package: in some cases it is necessary to purchase a second set of handles separately, although modern models are usually equipped with a complete set for both sides.
| Element | Action | Nuance |
|---|---|---|
| Upper loop | Move to the other side | Use new holes |
| Bottom hinge | Move or turn over | Check for pin presence |
| Handle | Remove and rearrange | Close old holes |
| Plugs | Rearrange crosswise | Observe color and texture |
Don't forget about mounting holes. On the front side, where there are no longer handles, you need to insert plastic plugs. They usually come with the refrigerator and are stored in a bag with documentation or are already installed on the back side. If the plugs are lost, they can be ordered from the service center.
Installing the lower support and pin
The lower hinge is often structurally different from the upper one. In some models Turk it is a pin inserted into the body, and in others it is a full-fledged plate with a bushing. When rearranging, it is important not to confuse the orientation of the parts.
If your model uses a removable pin, remove it from the old socket and insert it into a new, pre-prepared hole on the opposite side. Make sure it is seated all the way and locked. In some cases, it may be necessary to lubricate the pin with a small amount of graphite grease for quiet operation.
What to do if the holes do not line up?
In rare cases, budget models may only have holes on one side. In this case, you will need to drill the housing, which is not recommended to do yourself, since you can damage the insulating layer and break the tightness of the circuit. It is better to contact a service center or leave it as is.
Check the horizontal installation of the lower support. If this element is skewed, the door will open spontaneously or, conversely, close with force. Use a level for control. Accuracy at this stage is critical to the durability of the seal.
Installing the door in a new location
After preparing all the mounting points, you can begin hanging the door. Lift the door leaf and carefully slide it onto the bottom pin or bushing. Make sure that the door sits evenly and fits tightly to the body along the entire perimeter.
Now you need to fix the top hinge. Align the hinge holes with the holes on the refrigerator body. Insert the bolts and begin to tighten them by hand without applying excessive force. Only after making sure that the thread has gone correctly can you use the tool.
- 🔍 Visually assess the gaps between the door and the body - they should be uniform.
- 🚪 Check the ease of movement - the door should not creak or cling to the body.
- 🧲 Make sure that the magnetic seal fits tightly along the entire contour.
Final tightening of the bolts is carried out only after you are sure of the correct positioning. Excessive tightening force can lead to deformation of the metal or breakage of the thread, so proceed moderately. Tightening torque Should be sufficient for fixation, but without fanaticism.
Adjusting the position and checking the tightness
The final stage is adjustment. Even with perfect installation, (fine adjustment) may be required. Most models Biryusa have adjusting screws or the ability to change the height of the legs of the refrigerator itself to compensate for uneven floors.
Tightness testing is carried out using a simple method. Press a piece of paper between the door and the cabinet at various points around the perimeter. If the paper is pulled out with force, then the compactor is working correctly. If the sheet falls out freely or gets stuck tightly, adjustment is required.
⚠️ Attention: If after rehanging the door does not close tightly, check whether anything is interfering with the seal (for example, food on the shelves or incorrectly installed dishes).
It is also worth paying attention to the work closer (if it is in your model). When tilting the refrigerator backwards, the door should close on its own due to gravity. If this does not happen, try slightly unscrewing the front adjustable supports to create the necessary slope back.
Common errors and ways to eliminate them
When doing work on their own, beginners often make common mistakes. One of the most common is the loss of fasteners. It is better to place all screws and plugs in a magnetic tray or labeled container so as not to confuse their purpose.
Another mistake is ignoring the instructions for a specific model. Refrigerators Biryusa have been produced for decades, and hinge designs in models of the 1990s and modern versions can be radically different. Always check the product data sheet.
| Problem | Possible cause | Solution |
|---|---|---|
| The door is skewed | Uneven tightening of bolts | Loosen and retighten crosswise |
| Creak when opening | Lack of lubrication in hinges | Lubricate hinges graphite or silicone |
| Does not keep cold | The seal is damaged | Replace the sealing rubber |
| The door slams | The gap is too large | Adjust the height of the refrigerator legs |
If you notice that after all the manipulations the refrigerator starts to work louder or vibrations appear, check if the door is touching any protrusions or pipes at the back. Sometimes, when the body is skewed, contact becomes possible.
Is it possible to rehang the door if the second handle is not included?
In most modern models Biryusa the second handle is already installed on the back side or is in the bag with the documents. If it is not there, you can try to order an original spare part using the catalog number. Using non-original handles may lead to disruption of the opening geometry.
Do you need to defrost the refrigerator before rehanging?
Full defrosting is not necessary if you work quickly. However, if you plan to tilt the refrigerator too far or place it on its side, it is best to wait until it defrosts to prevent water from the drainage system from getting on the electrical components. It is enough to simply turn off the device 10-15 minutes before starting work.
Will the temperature settings be lost after disconnection?
Electronic settings may be reset to factory values if unplugged for a long time. Mechanical controls (thermostats) will remain in their position. After turning on, let the refrigerator operate for several hours without loading food so that it returns to normal mode.