Rearranging the shelves in the Atlant refrigerator: instructions with photos and tips

Rearranging the shelves in the refrigerator Atlantic is a task that every owner faces sooner or later. Whether it’s buying a large saucepan, the desire to optimize space for new products, or banal cleaning, the ability to properly adjust the internal elements will save time and nerves. However, not everyone knows that incorrect rearrangement can lead to breakage of fasteners, loss of tightness, or even damage to the compressor.

In this article we will analyze step-by-step algorithm for all popular models Atlant (from classic MXM-170 to modern NRM with the system No Frost), we will tell you about types fastenings and give advice on how to avoid common mistakes. You will also find out which shelves you can rearrange yourself, and which ones are absolutely not recommended to touch - and why.

We warn you right away: if your refrigerator is under warranty, any intervention in the design (including rearranging shelves) may cause a refusal of service. Check this point in warranty card or with the official dealer Atlantic.

Types of shelves in Atlant refrigerators: which can be rearranged and which cannot

Not all shelves in refrigerators Atlantic are designed for permutations. For example, glass shelves with metal edging usually removable and adjustable, but plastic guides on the back wall you should not touch - they fix the air circulation system.

Let's look at the main types:

• 🔹 Glass shelves —the most universal. They can be adjusted in height, removed for washing, and even rotated (in some models). Usually mounted on plastic or metal brackets.
• 🔹 Plastic shelves - often found in freezers. They can be rearranged, but are less durable than glass. Maximum load - up to 5 kg.
• 🔹 Shelves with locks - in models with No Frost (for example, Atlant XM 6025-031). They can be adjusted, but only within special grooves.
• 🔹 Fixed elements — back wall, shelves with built-in ventilation holes or temperature sensors. Rearranging them may disrupt the operation of the system.

In refrigerators Atlantic older than 2010 are often found metal grids instead of glass shelves. They can be rearranged, but they are less easy to clean and can rust when exposed to moisture.

How to determine the type of shelf in your model?

Open the refrigerator and inspect the fasteners:

- If the shelf is holding on protrusions on the side - it can be adjusted in height.

- If the fastenings hidden under rubber plugs are a non-removable element.

- In models with No Frost shelves often have special grooves for fixing.

Preparation for rearrangement: what needs to be done before starting work

Before you start adjusting the shelves, complete several mandatory steps:

1. 🔌 Disconnect the refrigerator from the mains. This will prevent the compressor from accidentally turning on during work (vibration can throw off the settings).
2. 🧊 Thaw the freezer compartment (if the rearrangement affects it). Ice on the walls will complicate access to the fasteners.
3. 📦 Unload all the food. Even light packages can interfere with maneuvers. Use a cooler bag or put the food in a cool place.
4. 🧽 Wipe the shelves and walls. Dirt and moisture can get into the grooves of the fasteners and make installation difficult.

If your model has electronic display (for example, in Atlant XM 6321-100), remember or take a photo of the current temperature settings. After disconnecting from the network, they can be reset.

Unplug the refrigerator|

Remove all products|

Prepare a rag and detergent|

Check the fasteners for cracks|

Inspect the rubber seal on the door|-->

⚠️ Attention: In refrigerators with a system No Frost it is not recommended to rearrange the shelves freezer unless absolutely necessary. This can disrupt the circulation of cold air and lead to icing of the fan.

Step-by-step instructions: how to remove and rearrange the shelf in the Atlant refrigerator

The algorithm of actions depends on the type of fasteners. We will consider the two most common options: shelves on brackets (in most models) and shelves with grooves (in refrigerators with No Frost).

Option 1: Shelves on brackets (classic models)

This type of fastening is found in Atlant MKhM-170, MKhM-180 and other budget models. The shelves here are held on plastic or metal protrusions.

1. 🔍 Determine the level of fastening. Usually there are several pairs of grooves on the side walls (from 3 to 5). Select the appropriate height.
2. 🖐️ Lift the shelf up and pull it towards you. If it is tight, do not apply force - check if it is caught on the back wall.
3. 🔄 Move the brackets to the desired level. In some models, you can simply move them manually, in others you will need to press the lock.
4. 📌 Put the shelf back, starting from the rear edge, make sure that it fits evenly into the grooves.

Option 2: Shelves with grooves (No Frost)

In refrigerators with No Frost (for example Atlant XM 6026-000) the shelves are fixed in special guides. Here it is important not to disturb the position of the ventilation ones. holes.

1. 📏 Measure the distance between the grooves at the new height. It should coincide with the width of the shelf.
2. 🔧 Tilt the shelf at an angle of 45° and pull it out of the grooves. pull it straight - you can break the clamps.
3. 🔀 Check compatibilitySome shelves in No Frost have asymmetrical fastenings and are only suitable for certain levels.
4. 🔒 Insert the shelf into the grooves, starting from the back, and lower until it clicks.

In Atlant models with electronic control (for example, Atlant XM 6324-100), after rearranging the shelves, you may need to reset the errors. To do this, press and hold the button Super Cool within 5 seconds.

Common mistakes and how to avoid them

Even such a simple operation as rearranging shelves can turn into problems if ignore the nuances. Here are the most common mistakes and ways to prevent them:

• 🚫 Ignoring weight restrictions. The shelves in the freezer are designed for less load than in the refrigerator. If you put heavy foods on them (for example, large quantities of frozen meat), they may crack.
• 🚫 Incorrect extraction angle. If you pull the shelf straight towards you, you can break the fasteners. Always lift it up at an angle of 30–45°.
• 🚫 Rearranging shelves while the compressor is running. Vibration can dislodge the shelf and jam it in the grooves. Always turn off the refrigerator before making adjustments.
• 🚫 Use of sharp objects. Some try to pry the shelf with a knife or screwdriver - this scratches the plastic and damages the seals.

Another typical problem is level mismatch after rearrangement. For example, if in the model Atlant XM 6026-000 the shelf is moved too high, it can block access to the ventilation holes, which will lead to overheating compressor.

⚠️ Attention: In refrigerators with inverter compressor (for example, Atlant MY 3104-000) after rearranging the shelves, noise may temporarily increase. This is normal - the system adapts to the new air distribution. If the noise does not go away after 2-3 hours, check whether the shelf is blocking the ventilation grilles.

Rearrangement features shelves in the freezer

The freezer requires a special approach. Here the shelves are often made of plastic (as opposed to glass in the refrigerator) and have a lower load capacity. In addition, in models with No Frost rearrangement may affect the operation of the defrosting system.

Basic rules:

• ❄️ Do not rearrange the shelves during defrosting. Plastic becomes brittle at low temperatures.
• ❄️ Avoid contact of shelves with the evaporator (back wall). This may lead to icing.
• ❄️ Check the location of the temperature sensor. In some models, it is attached to the shelf - if it is removed, the sensor may move.

In freezers Atlant are often used drawers instead of shelves. They can be rearranged in height, but only within the guides. If the drawer is difficult to move, do not try to pull it out by force - lubricate the guides with silicone grease (do not use oils!).

How to secure a shelf if it is wobbly or sagging

If, after rearranging, the shelf dangles or sags under the weight of the food, the problem may be:

• 🔧 Worn fasteners (especially in refrigerators older than 5 years).
• 🔧 Improper installation (the shelf does not fully fit into the grooves).
• 🔧 Flange deformation (for example, after washing with hot water).

Solutions:

1. 🔄 Reinstall the shelf. Remove it and reinstall it, making sure that both edges fit evenly into the grooves.
2. 🛠️ Fold the brackets. If they are plastic and loose, carefully bend them with pliers (do not overdo it!).
3. 📌 Use additional fasteners. Refrigerator spare parts stores sell silicone gasketswhich can be placed under the shelf for better fixation.
4. 🔧 Replace fastenings. If the brackets are broken, buy new ones (specify the refrigerator model!). For Atlant are suitable.If the shelf is cracked, do not try to repair it with tape or glue - it is unsafe. Order a new one at the service center universal fastenings from Indesit or Beko.

If a shelf is cracked, do not try to repair it with tape or glue - it is unsafe. Order a new one from the service center Atlantic or select an analogue in size.

When is it better to contact a specialist: signs of serious problems

In most cases, rearranging shelves can be done independently, but there are situations when it is better to call a specialist:

• 🚨 The shelf broke inside the grooves, and its fragments are blocked mechanism.
• 🚨 After rearrangement, the refrigerator began to make noise or freeze poorly.
• 🚨 The shelf fastenings were welded to the wall (in older models due to corrosion).
• 🚨 An error appeared on the display (for example, E1 or F2 - this may mean a problem with the sensors).

The average cost for a technician to come out to adjust the shelves is from 800 to 1500 rubles (depending on region). If the problem is in the fasteners, replacing them will cost 300–600 rubles per piece (excluding work).

⚠️ Attention: If after rearranging the shelves the refrigerator started turn on more often or poor cooling, check that the ventilation holes are not blocked. In models with No Frost this can lead to evaporator icing fan failure.

FAQ: Frequently asked questions about rearranging shelves in Atlant refrigerators

Is it possible to rearrange shelves in an Atlant refrigerator with No Frost?

Yes, but with caution. In models with No Frost shelves are often connected to the ventilation system. Replace them only in the slots provided for this purpose and do not block the holes on the back wall. In the freezer, it is better not to touch the shelves unless necessary - this can disrupt air circulation.

Why did the refrigerator become louder after moving the shelf?

This may be due to:

• 🔊 Blocking the ventilation holes (in models with No Frost).
• 🔊 Displacement of the temperature sensor (if the shelf touched its mount).
• 🔊 Vibration of the shelf, which is transmitted to the body.

Check whether the shelf is level and, if necessary, adjust its height.

How remove the glass shelf if it is jammed?

Do not pull it by force! Try:

1. 🔹 Gently rock the shelf left and right to free it from possible snagging.
2. 🔹 Heat the grooves with a hairdryer (no more than 30 seconds!) - plastic will expand slightly.
3. 🔹 Lubricate the fasteners with silicone grease (not with oil!).

If that doesn’t help, call a technician - independent attempts can lead to cracks.

Is it possible to place shelves from one Atlant refrigerator into another?

Only if the models are identical in size and type of fastenings. For example, shelves from Atlant MHM-170 are not suitable for Atlant XM 6026-000, even if they look similar. data-i="301">Atlant MHM-170

• 📏 Width and depth shelves.
• 🔧 Type of fastenings (brackets, grooves, clamps).
• 🏗️ Material (glass, plastic, metal).

What to do if, after rearranging the shelves, the refrigerator began to freeze worse?

Most likely, you blocked the ventilation holes or the temperature sensor has been moved. Return the shelves to their original position and check:

• ❄️ Whether the shelf is blocking the air flow in the freezer.
• ❄️ Is the sensor positioned correctly (in some models it is attached to the shelf).
• ❄️ Is there any formation? ice on the back wall (this is a sign of poor circulation).

If the problem persists, call a technician for diagnosis.