Re-hanging the door refrigerator Indesit is a task that many owners face when moving, renovating a kitchen, or simply wanting to change the opening side. Despite the apparent complexity, the procedure is quite doable at home if you know the key points: from correct dismantling of hinges to precise adjustment of the seal. In this article, we will analyze the process step by step, taking into account the features of popular models. data-i="52">hidden hinges are often found, while in classic units there are open ones. We will consider a universal algorithm that is suitable for most options, but Indesit (For example, BIAA 13, C 132 G or TIA 16).
It is important to understand that the design of refrigerator doors Indesit may vary depending on the series and year of manufacture. For example, for models with a system No Frost Hidden hinges are often found, while in classic units there are open ones. We will consider a universal algorithm that is suitable for most options, but before starting work, be sure to check the presence of holes for attaching hinges on the opposite side - their absence means that hanging the door is not provided by the manufacturer.
If you have never done such work, do not worry: the article contains it. checklists, warnings about common errors and even a survey that will help determine your level of preparation. And for those who are afraid of damaging the seal or hinges, we have prepared a spoiler with the consequences of incorrect dismantling.
Preparing for reinstallation: tools and safety measures
Before you start work, make sure you have everything you need to hang the door. refrigerator Indesit you will need:
- 🔧 Phillips screwdriver (usually PH2) - for most hinges and fasteners.
- 🔧 Hex wrench (size depends on the model, usually 4 or 5 mm) - for some modern units.
- 📏 Ruler or tape measure —to measure gaps after installation.
- 🧲 Magnet or screwdriver with magnetic tip —for ease of working with small screws.
- 🧴 Silicone grease (optional) - for processing hinges after installation.
Also prepare the work space: free access to the refrigerator from all sides, unplug it from the network and completely defrost (if the model is not No Frost). This is important, since when dismantling the door, the elements of the cooling system may be damaged. Do not forget that the weight of the door with shelves can reach 10-15 kg - it is better to work with an assistant.
⚠️ Attention: If your refrigerator Indesit is equipped with a display or an electronic control unit on the door, overweight required disconnect the power connectors and signal cables. Their damage can damage the entire system!
It is worth noting that in some models (for example, Indesit ITF 118) the door the freezer compartment is hung separately from the main one. Check this in the instructions for your appliance. If the documentation is lost, look for it on the official website Indesit by the model number (usually indicated on a sticker inside the chamber or on the back wall).
Dismantling the old door: step-by-step algorithm
Start with the top hinge - it usually fixes the main load. decorative plugs (if any), under which the mounting screws are hidden. In models Indesit with open hinges, the screws can be hidden under plastic caps - pry them off with a flat screwdriver.
Next proceed as follows:
- Unscrew the screws of the top hinge (usually 2-3 pieces), but do not remove it completely - just loosen it so that the door can be lifted.
- Hold the door, carefully remove it from the lower pin (or unscrew the lower hinge, if the design is different).
- Put the door on a soft surface (for example, a blanket) so as not to damage the coating.
- Remove the lower hinge and plugs on the opposite side (if there are any).
At this stage, many people make a mistake: they try to remove the door without unscrewing all the screws or without holding it. This risks the door falling and damaging the hinges or seal. Also pay attention to gaskets and washers —they need to be saved and installed back in the same order.
What happens if you remove the door incorrectly?
If the door falls or is dismantled with a jerk, you can bend the hinges, damage the rubber seal, or even crack the plastic door body. In the worst case, you will have to replace the hinges or the entire door, which will cost. 30–50% of the cost of a new refrigerator.
If your refrigerator is a two-chamber one, the process of dismantling the freezer door is similar, but additional disconnection of wires may be required (for example, for lighting or sensors). In this case, take a photo of the connection diagram. before disassembling.
Transferring loops to the other side: nuances and diagrams
After dismantling the door, you need to move the hinges to the opposite side. There are several key points:
- 🔄 Symmetrical holes: Most models already have holes for the hinges on both sides, but they are closed with plugs. there are no holes - re-hanging the door Indesit There are already holes for the hinges on both sides, but they are closed with plugs. If there are no holes, rehang the door not provided!
- 📐 Marking: If there are no plugs, carefully drill new holes according to the template (use old hinges as a stencil).
- ⚙️ Adjusting screws: In some models (for example Indesit BIA 18) the hinges have eccentrics for height adjustment - do not lose them!
The loop transfer scheme usually looks like this:
| Element | Action | Note |
|---|---|---|
| Upper loop | Move to the opposite side, mirrored | Screws do not tighten all the way to adjustLater |
| Bottom loop | Similar to the top, but the pin may need to be repositioned | In some models, the pin enters the body - it needs to be removed and inserted on the other side |
| Plugs | Install on old holes | Use original plugs from the kit |
| Sealant | Check for deformation after rehanging | When need to warm up with a hairdryer to restore the shape |
Pay special attention lower loop. In models with a system Total No Frost (for example, Indesit ITF 118 W) it can be attached to the frame of the freezer - in this case, partial disassembly of the case will be required. If you are not confident in your abilities, it is better to contact. master.
⚠️ Attention: In refrigerators Indesit s electronic control on the door (for example, Indesit ITR 5200 W) after rehanging may be required reflashing the control unit, since sensors door positions change orientation. Check this with the service center!
Installing the door on a new side: adjustment and testing
When the hinges have been transferred, you can begin installing the door. Start with the top hinge:
- Place the door on the bottom pin (or temporarily fix the bottom hinge).
- Align the door vertically and horizontally, then tighten the screws of the top hinge not completely.
- Close the door and check the gaps around the perimeter. They should be the same (1–2 mm).
- Adjust the position of the door by tightening the hinge screws, then tighten them.
After installation, check:
- 🔹 Tightness of fit seal —if gaps remain, the door needs to be adjusted.
- 🔹 Ease of opening/closing —the door should move smoothly, without creaks.
- 🔹 Sensor performance (if any)—after rehanging, an error may appear on the display.
If the seal is deformed, heat it with a hairdryer (temperature no higher than 60°C) and shape it with your hands. As a last resort, replace it with a new one (the article number can be found in the instructions or on the website Indesit).
The door opens 90° without effort|
The seal fits evenly around the entire perimeter|
No distortions or play when closing|
All screws are tightened, but not overtightened-->
In models with water dispenser (for example, Indesit ITF 160after re-hanging, you may need to reconfigure the water supply. To do this, you need to remove the dispenser panel and reconnect the tubes. If you are not sure, it is better to call a specialist.
Typical mistakes and how to avoid them
Even with careful work, you can make mistakes that will lead to incorrect operation of the refrigerator. Here are the most common ones:
- 🚫 Tightening the hinge screws - this leads to deformation of the door or breakage of the thread. with a force of no more than 1–1.5 Nm.
- 🚫 Ignoring gaskets - without them the door will hang or not close tightly.
- 🚫 Incorrect installation of the seal - if it is twisted or displaced, the refrigerator will be worse cool.
- 🚫 Lack of adjustment after installation —even a perfectly installed door can sag in a month or two.
If, after rehanging, the refrigerator begins to operate loudly or condensation appears on the walls, it is most likely broken tightness. Check the seal and adjust the hinges. In models with No Frost leak closing of the door can lead to freezing of the evaporator and malfunction of the system.
Another common problem is creaking. hinges. It occurs if the hinges are not lubricated or installed crookedly. Use silicone grease (not oil!) to eliminate the sound, check the alignment of the hinges - perhaps one of them is misaligned.
Features of re-hanging doors in Indesit models with No Frost
Refrigerators Indesit with system No Frost (for example, Indesit DF 5200 W) have their own nuances when re-hanging doors:
- ❄️ Additional sensors —temperature or humidity sensors may be built into the doors, which need to be carefully disconnected.
- ❄️ Ventilation channels —when dismantling, do not damage the plastic air ducts coming from the evaporator.
- ❄️ Electronic unit —if it is located on the door, you will need to reconnect the connectors.
In such models, before starting work required unplug the refrigerator and wait until it is completely defrosted (at least 12 hours). the system No Frost includes heating elements that can be damaged by mechanical action.
After rehanging the door in the refrigerator, check: No Frost check:
- 🔹 Operation fan (there should be no extraneous noise).
- 🔹 No errors on the display (if any).
- 🔹 Uniform distribution of cold in the chambers.
⚠️ Attention: In some models Indesit s No Frost (for example, Indesit ITF 118 S) after re-hanging the door it is required reset settings through the service menu. Reset instructions can be found in the technical data sheet or on forums for repairing household appliances.
When is it better to turn to a professional
Despite the fact that re-hanging the refrigerator door Indesit can be done independently, in some cases it is better to trust the master:
- 🛠️ If your model is equipped touch display on the door —there is a high risk of damaging the electronics.
- 🛠️ If the refrigerator is under warranty, self-repair can void it.
- 🛠️ If during dismantling you find corrosion of hinges or fasteners —they need to be replaced, not rearranged.
- 🛠️ If the door is after rehanging does not stay closed —this may indicate wear of the seal or deformation of the body.
The cost of professionally re-hanging the door in service centers Indesit usually amounts to 1,500–3,000 rubles (depending on the model and region). This is not so expensive, considering the risks of damaging the refrigerator when working independently. For example, replacing a broken hinge will cost 2. 000–4,000 rubles, and a new door - up to 15,000 rubles.
If you still decide to act on your own, but encounter difficulties, look for video instructions specifically for your model. For example, on YouTube there are detailed analyzes for Indesit BIAA 13, Indesit C 132 G and other popular series.
FAQ: Frequently asked questions about reversing the door of an Indesit refrigerator
Is it possible to rehang the door on an Indesit refrigerator if there are no openings on the other side? hinges?
No, if the manufacturer has not provided holes for attaching hinges on the opposite side, re-hanging the door impossible without drilling a new body can break the tightness and lead to breakage. In such cases, the only way out is to order a mirror door from the manufacturer (if it is provided for your model).
How to understand that the door seal is damaged and needs to be replaced?
Signs of a worn seal:
- Condensation or ice appears on the walls of the refrigerator.
- Door closes with difficulty or, on the contrary, opens too easily.
- The rubber has lost its elasticity, is cracked or deformed.
- When the door is closed, a gap of more than 2 mm is visible between it and the body.
If at least one of the points matches, it is better to replace the seal. Indesit original rubber bands cost from 800 to 2,500 rubles.
Do you need to defrost the refrigerator before hanging the door?
Yes, requiredeven if you have a model with No Frost, before. By dismantling the door, the refrigerator must be disconnected from the network and completely defrosted. This is due to:
- Safety - when working with electronics (if there is one on the door), the risk of a short circuit is reduced to zero.
- Convenience - a defrosted seal is easier to remove and install. back.
- Safety of equipment - in the freezer, when dismantling the door, the evaporator may be damaged.
An exception is refrigerators with the function Holiday (vacation), which maintain a minimum temperature, but it is better to defrost them before work.
How long does it take to rehang a door?
On average, the procedure takes from 1 to 3 hours, depending on:
- The experience of the master (a beginner will need more time).
- The complexity of the design (models with No Frost or electronic it takes longer to disassemble the block).
- The presence of an assistant (it is more difficult to cope alone, especially with heavy doors).
If you are doing this for the first time, set aside the work half a day - taking into account preparation, adjustment and checking.
What to do if, after rehanging, the door does not close tightly?
The problem usually lies in:
- Incorrect adjustment of the hinges - loosen the screws and adjust the door position vertically/horizontally.
- Deformed seal —heat it with a hairdryer (t ≤ 60°C) and shape it or replace it.
- Warped refrigerator body —check whether it is level (use a level).
- Ingress of foreign objects —inspect the seal for crumbs or debris.
If all else fails, the hinges may be worn out and need to be replaced.