We rehang the door of the Atlant 1709 refrigerator with our own hands: from A to Z

Re-hanging the refrigerator door Atlant 1709 is a task that many owners face when moving, renovating a kitchen, or simply wanting to change the opening side. Unlike modern models with universal hinges, this Belarusian technology requires accuracy and knowledge of the nuances. Incorrect dismantling can lead to damage to the seal, misalignment of the door, or even breakage fastenings - and this is already a reason for expensive repairs.

On the other hand, with the right approach, the whole procedure will take no more than an hour, will not require special skills and will save you 1,500–3,000 rubles (that’s what craftsmen charge for such a service). In this article - step-by-step instructions with photos, a list of tools, typical errors and tipshow to avoid problems. We took into account all the features of the model 1709, including the location of the hinges, the nuances of fastening the seal and the adjustment procedure after installation.

If your refrigerator is still under warranty - rehanging the door can invalidate it. Check this point with the service center Atlant before starting work. Also check whether the holes for the hinges on the opposite side are covered with decorative plugs (some batches do not have them, and you will have to purchase them separately).

1. Preparation: tools and conditions

For work you will need a minimum set of tools, but you won’t be able to do without them. Do not use improvised means (knives, screwdrivers of the wrong size) - this can lead to thread breakage or damage to plastic parts.

• ⚒️ Phillips screwdriver (PH2 size - standard for household appliances)
• 🔧 10 mm wrench (for fixing the hinges)
• 📏 Level (to check the vertical after installation)
• 🧲 Magnet or screwdriver with a magnetic tip (so as not to lose small screws)
• 🧴 Silicone grease or WD-40 (if the hinges are tight)

Before starting work unplug the refrigerator and empty the door shelves of products. If the model has a system No Frost, wait 1-2 hours for the ice on the evaporator to melt - this will make access to the fasteners easier. Do not turn the refrigerator over - compressor oil may get into the circuit, which will lead to breakdown.

⚠️ Attention: On models Atlant 1709 released before 2021, the top hinge is attached four screws, and the bottom - three. Make sure you have enough fasteners for the reverse side (sometimes they are hidden under plugs).

Is the refrigerator unplugged from the outlet?

Have all products been removed from the door shelves?

Are there spare screws/plugs for the opposite side?

Is the area prepared for laying the door (soft surface)?-->

2. Dismantling an old door: step-by-step algorithm

Start with the top hinge - it usually fixes the door in a vertical position. Do not remove the bottom hinge firstotherwise the door may fall and damage the seal or plastic case.

1. Open the door to 90° and support it chair or assistant. This will prevent you from falling when the fastenings are loosened.

2. Unscrew decorative cover the top hinge (it is secured with latches or one screw). Under it you will see 4 screws.

3. Loosen the screws of the top hinge 2-3 turns, but do not unscrew completely. Hold the door - it will begin to “walk.”

4. Carefully lift the door up, remove it from the lower pin and place it on a soft surface (for example, a blanket).

Now you can unscrew the bottom loop. It is important not to lose here adjusting washers —they are responsible for the correct clamping of the door. Take a photo of their location before dismantling.

What to do if the screws do not unscrew?

If the fasteners are “stuck” or the paint is in the way, use WD-40. Apply the product for 10-15 minutes, then try again. Do not apply excessive force -breaking the screw head will complicate the task. As a last resort, you can drill out the screw with a drill with a thin drill bit (2–3 mm), but this is risky for a plastic case.

3. Transferring the hinges to the opposite side

On the refrigerator box Atlant 1709 the holes for the hinges on the opposite side are usually closed plastic plugs. They need to be carefully pryed off with a flat screwdriver and removed. If there are no holes, you will have to drill new ones (diameter 8 mm), but this is rare for this model.

Move the hinges in a mirror image:

• 🔄 The upper loop goes to left side (if the door now opens on the right).
• 🔄 The lower loop goes to there is a right side (taking into account the pin for canopy).

Critical important point: on the lower hinge adjusting bolt (usually with a lock nut). When moving, do not change its position - this will ensure correct clamping of the door after installation. If the bolt is unscrewed, the door will hang.

4. Installing the door on new hinges

This is the most critical stage. Improper installation can lead to misalignment, poor seal fit and cold leakage. Follow the algorithm:

1. Place the door on bottom pin hinges, holding it in a vertical position.

2. Align the top so that the holes for the screws coincide with the hinge. Do not tighten the screws immediately - screw them in 1-2 turns first.

3. Check that the door opens/closes without effort. If it is tight, loosen the top hinge and adjust the position.

4. Tighten all screws crosswise (top first, then bottom) to avoid distortion.

On the model Atlant 1709 between the door and the body there should be a gap of 2-3 mm around the entire perimeter. If the gap is larger, tighten the lower loop with the adjusting bolt.

5. Adjusting and checking the tightness

Even if the door is visually level, this does not guarantee tightness. A poor fit of the seal increases energy consumption by 15–20% and leads to freezing of the back wall.

How to check the tightness:

• 📄 Take sheet of paper A4 format.
• 🚪 Close the door, holding the sheet between the seal and the body.
• 🤏 Try to pull out the sheet. If it slips out without effort the seal does not fit well.

To adjust:

1. Loosen upper loop and slightly move the door towards the body.
2. Tighten lower adjustment bolt (clockwise - the pressure is stronger).
3. Repeat the test with paper. Optimal resistance - the sheet is pulled out with force, but does not tear.

⚠️ Attention: If, after adjustment, the door begins to close tightly, check whether it is skewed vertically. Use a level - a deviation of more than 2 mm will lead to spontaneous opening.

6. Typical mistakes and how to avoid them

Even with the apparent simplicity of the process, many make mistakes that then have to be corrected at the service center. Here are the most common:

• 🔩 Thread breakage in hinges - occurs due to the use of an unsuitable screwdriver or excessive force. Solution: Tighten the screws smoothly, without jerking.
• 🚪 Door skewed -usually due to uneven tightening of the hinges. Solution: tighten the screws crosswise, like the wheels of a car.
• 🧊 Damage to the seal — if the door fell or was pulled by the handle during dismantling. Solution: before work, remove the handle (it is secured with 2 screws).
• ⚡ Forgot to turn off the refrigerator —this is dangerous! When dismantling, you can damage the backlight wires or sensors. Solution: always unplug the plug from the socket.

Another common problem - extraneous sounds (creaking, knocking) after re-hanging. Reasons:

• The hinges are not lubricated (use silicone greasebut not oil!).
• The screws are not fully tightened (check all fastenings).
• The door touches the shelves (adjust the height of the legs of the refrigerator).

7. Additional tips for the model Atlant 1709

This model has several features that are rarely written about in general instructions:

• 🔄 The door handle symmetrical - it does not need to be rearranged. But if it interferes, remove it by unscrewing 2 screws from the back side.
• 🧲 Magnetic seal is Atlant 1709 more rigid than in other models. If the door does not close well, try warm up the seal hairdryer (temperature 50–60°C) - this will restore its elasticity.
• 🔧 Spare screws for hinges can be ordered from an authorized dealer (article: ATL-0045 for the top hinge, ATL-0046 for the bottom).

If your refrigerator is with display or electronic control, after reweighing it may be required reset settings. To do this:

1. Unplug the refrigerator for 5 minutes.
2. Turn on and hold the button Super Cool 10 seconds.
3. Wait for the beep - this means the system has rebooted.

⚠️ Attention: On some batches Atlant 1709 (2020-2022 release) the bottom hinge has plastic linerwhich may crack if over-tightened. Tighten the screws with a force of no more than 1.5 Nm (use a torque wrench if available).

FAQ: Frequently asked questions about reweighing doors

Is it possible to hang the refrigerator door Atlant 1709 alone?

Technically, yes, but it’s inconvenient. The door weighs 8–10 kg and must be held and leveled at the same time. If there is no assistant, use table or stoolto support the door during installation. The main thing is not to drop it so as not to damage the seal.

What to do if after hanging the door does not close tightly?

There are several reasons:

1. The hinges are not adjusted correctly - loosen the top and tighten the bottom one.
2. The seal is deformed - warm it with a hairdryer or replace it.
3. The refrigerator is not level - adjust the legs according to the level.

Check the gap around the entire perimeter - it should be the same (2-3 mm).

Is it necessary to rehang the freezer compartment if it is separate?

In the model Atlant 1709 the freezer compartment is usually located at the bottom and has common door with a refrigerator compartment. Only one door needs to be re-hung. If you have a two-door model (for example Atlant 1709-100), then the freezer will also have to be re-weighed, but the hinges are different - you will need a separate set of fastenings.

How much does it cost to rehang a door in a service center?

The cost of work in official services Atlant (for 2026) is 1500–2500 rubles, depending on the region. In private workshops, the price may be lower (1000–1500 rubles), but there is a risk of running into unskilled craftsmen. If the refrigerator is under warranty, some services do it for free (check by calling the hotline).

Is it possible to rehang the door without removing it completely?

Theoretically, yes, but this is extremely inconvenient and is fraught with damage. Hinges Atlant 1709 require complete dismantling of the door to be transferred to the other side. Attempts to take shortcuts often end in thread failure or misalignment. The exception is if you are simply adjusting existing hinges (for example, tightening the bolts).