The situation when standard opening of the refrigerator door becomes inconvenient due to the peculiarities of the kitchen layout occurs quite often. Appliance owners often look for information on how to hang the door of a Beko refrigerator to gain access to food from the right side. Fortunately, most models of this Turkish brand are designed to provide the ability to reinstall the hinges without calling a technician.
Before starting work, you must carefully study technical data sheet your device, since the design may differ depending on the series. Some models require removing the top cover, others require removing decorative plugs. Video instructions often demonstrate the general process, but the specific nuances of attaching the handles may vary.
This procedure requires care and a basic set of tools so as not to damage the enamel or plastic elements of the case. An incorrect sequence of actions can lead to skewing of the canvas and failure of the seal. In this article, we will analyze all the stages in detail so that you can complete the work efficiently and safely.
Necessary tools and preparation of the workplace
Before starting dismantling, you need to prepare a flat and free area where it will be convenient to lay out the removed parts. You will need a stable surface to rest the door on while rearranging the hardware. The absence of unnecessary objects around minimizes the risk of accidental impact or loss of small screws.
The basic set of tools usually includes a Phillips and flat-head screwdriver, as well as a wrench or socket of the appropriate size. For some models Beko you may need a hex key, which is often included with the equipment. It would also be a good idea to have a soft rag or cardboard on hand to protect the floor and door covering.
⚠️ Attention: Before starting any work, be sure to disconnect the refrigerator from the power supply by removing the plug from the outlet. This is critical for safety, since you will be working in close proximity to electrical components and wiring.
Pay special attention fastenersthat you will be unscrewing. It is best to put them in a separate container with a magnetic bottom or labeled container so as not to mix up the top and bottom screws. The loss of even one bolt can make it impossible to securely fix a heavy door.
☑️ Preparing for rehanging
Analysis of the design and search for video materials
Searching for a high-quality video for the query “how to hang a refrigerator door beko video” often becomes the first step for many users. Visualization of the process helps to understand the principle of operation of the mechanism, but it is important to find a video that matches your specific series of devices. Models with a bottom freezer and two-chamber options may have differences in design.
When viewing instructional materials, pay attention to the location of electrical connector indication controls. In modern models, the wires may pass through the top or bottom loop and must be carefully disconnected. Ignoring this step will make it impossible to install the door on the new side.
Where can I find the exact diagram for your model?
Official diagrams are often located on the inside of the door or on the back wall of the refrigerator. You can also enter the full model number (for example, RCNE520E23ZXPN) into the search bar on the manufacturer's website to download a PDF manual.
It is worth noting that not all hinges can be re-hinged. There are models with non-removable handles or integrated mechanisms, where changing the opening side is not provided by the factory. Checking this information in the documentation will save you time and effort.
Step-by-step instructions: dismantling the door
The process of removing the door begins with dismantling the top hinge, which holds the bulk of the leaf. Carefully remove the decorative plug, if present, and unscrew the mounting bolts. At this moment, the door must be held, as it can move under its own weight.
Next you should disconnect control cableif it passes through the top part. The connector is usually secured with a plastic lock, which must be released before pulling the plug out. Proceed without sudden movements to avoid damaging thin wires or contacts.
| Beko model type | Wire arrangement | Top loop type | Complexity |
|---|---|---|---|
| Single-chamber | Often absent | Simple plate | Low |
| No Frost (bottom seam) | Top loop | Complex mechanism | Medium |
| Combined | Through door hinge | Double hinge | High |
| Side-by-Side | Hidden wiring | Integrated | Very high |
After turning off the electrics, remove the door from the lower support axis and place it on the prepared surface. Now you can start rearranging stop pins and handles. Plastic plugs, included in the kit or already installed on the opposite side, are installed on the vacated holes.
Installing hinges and hanging the door
Installation on the new side begins with installing the lower support axis in symmetrical holes on the opposite side of the body. Make sure the axle is seated tightly and does not wobble. Then the door is put in place, and the top hinge is preliminarily fixed.
Pay special attention to the connection electrical connector. The wires must be laid in special grooves so as not to be pinched by metal when closing. Incorrect cable routing is a common cause of insulation damage and subsequent malfunctions.
The final step is to adjust the position of the door. If you notice a misalignment or loose seal, use the adjusting screws on the hinges. Ensure that the door closes tightly around the entire perimeter.
⚠️ Attention: Do not fully tighten the top hinge mounting bolts until you are sure that the door is level. Final fixation is carried out only after checking the gaps and parallelism of the body lines.
Adjustment and leak testing
After installation, it is necessary to conduct a thorough check of the quality of the work performed. The main criterion is the tightness of fit magnetic seal along the entire contour. To check, you can use a sheet of paper: clamp it between the door and the body at different points.
If the paper is pulled out too easily or, on the contrary, breaks, additional adjustment of the height of the refrigerator support legs or the position of the hinges is required. A uniform force when pulling the sheet indicates the correct setting.
It is also worth checking the operation of the door open alarm system. After connecting to the network, the indicators should light up and go out after a certain time, signaling that the temperature has been reached. Any failures in the indication may indicate poor contact in the connector.
Typical errors and ways to eliminate them
One of the most common errors is the loss or mixing up fasteners of different sizes. This leads to the fact that a short screw does not reach the thread, and a long one can pierce the plastic housing. Always check the length of the bolts before tightening.
Another problem is damage sealing rubber if the door is handled carelessly during a revolution. If the elastic is deformed, you can try to straighten it with a hairdryer, but in critical cases it will need to be replaced. Careful handling of the canvas will prevent this nuisance.
- 🔧 Ignoring the power outage can lead to a short circuit in the control circuit.
- 🔧 Door misalignment causes constant operation of the compressor and the formation of ice.
- 🔧 Insufficient tightening of the loops will lead to sagging and creaking over time.
If you have difficulties selecting a tool or understanding the diagram, it is better to contact official service centers. Self-repair always carries risks, especially when it comes to complex electronically controlled household appliances.
Is it possible to rehang a door if it has a glass insert?
Yes, it is possible, but increased caution is required. Glass makes the structure heavier and more fragile. It is recommended that two people work together to avoid hitting hard objects and chips.
Do you need to defrost the refrigerator before rehanging?
It is advisable, but not strictly necessary if you work quickly. However, the presence of ice may complicate access to some components, and water may leak when the body tilt changes during work.
What to do if the holes for the new side do not fit?
In 99% of cases, the holes are symmetrical. If they are not there, your model may not allow for overhang. Check the instructions: sometimes the holes are closed with factory plugs that need to be squeezed out.
Does re-hanging affect the warranty?
According to the conditions of most manufacturers, re-hanging the door yourself does not void the warranty if the unit components are not damaged. However, if controversial situations arise, the service may require evidence of the accuracy of the work.