Moving the Gorenje refrigerator door to the other side: instructions with photos and videos

Re-hanging the refrigerator door Gorenje is a task that owners face when moving, renovating a kitchen, or a banal desire to optimize space. Unlike models from other brands, equipment from the Slovenian manufacturer has its own design features: from the type of hinges to the location of the display mounts (if there is one). In 80% of cases, the procedure can be performed independently, without resorting to the help of a specialist, but only subject to strict adherence to the algorithm and taking into account the nuances of a particular model.

Many people mistakenly believe that it is enough to simply unscrew the hinges and fasten them in a mirror. In practice, it requires reconfiguration door level, reinstallation sealing rubber band (in some models), and sometimes adjustment of position opening sensor. In addition, refrigerators Gorenje series NRK i NK have hidden mounting holes under plugs that are easy to miss. This article will help you avoid common mistakes and get the job done the first time.

To avoid damaging the mechanism and not voiding the warranty (if it is still valid), check before starting work documentation for the model for restrictions. For example, in refrigerators with a system NoFrost and electronic control (ECO Cooling), additional calibration may be required after rehanging. Also note that models with built-in ice maker (for example, Gorenje RK 6292 AW) require a special approach due to the water supply hoses.

1. Preparation: tools and conditions

A minimum set of tools is required for work, but its absence can lead to thread breakage or damage to plastic elements. Here's what you need to prepare in advance:

• ⚒️ Phillips screwdriver (PH2) - for most hinges Gorenje.
• 🔧 Socket wrench or 10 mm socket - for models with metal hinges (for example, Gorenje NRK 6191).
• 📏 Level (bubble or laser) - to check the vertical after installation.
• 🧲 Magnet or screwdriver with a magnetic tip - so as not to lose small screws.
• 🧴 Silicone grease (optional) - for processing hinges after rehanging.

Before starting work unplug the refrigerator and free the door from all removable elements: shelves, trays, magnets If the model is equipped display (for example, Gorenje ORB153), take a photo of the location of the wires - you will have to disconnect them. Also prepare a clean surface for laying out the parts: hinges, plugs, mounting screws often look the same, but have different lengths.

Pay attention to the temperature in room. If the refrigerator has just been operating, wait 1-2 hours until sealing rubber returns to room temperature. Otherwise, it may become deformed during dismantling.

⚠️ Attention: In models with automatic defrosting (system Total NoFrost) after re-hanging the door, it may be necessary to reset the error E1 or E2 through the service menu. Reset instructions are usually indicated in the device passport.

2. Design features of Gorenje refrigerators

Refrigerators Gorenje are divided into three types according to the method of fastening the door:

1. Classic hinges - found in budget models (for example, Gorenje RK 4181). details.
2. Hinges with hidden fastenings - typical for the series NRK i NKRequire removal of plugs and relocation of mounting holes.
3. Hinges with electronic components —in models with a display (Gorenje ORB173). data-i="114">on the top hinge. They are responsible for

The key difference from other brands is the availability adjusting screws on the top loop. They are responsible for door clamp and often require adjustment after rehanging. The table below shows typical parameters for popular series:

In models with French door (for example, Gorenje R6192) the process is complicated by the need for synchronous re-hanging of both leaves. Here you cannot do without an assistant: one door is fixed in the open position while the second is being reinstalled.

3. Step-by-step instructions for rehanging the door

Let's look at the universal algorithm using an example. model Gorenje NRK 6191 (the most common option). For other series, the steps may differ slightly - be guided by the design of your refrigerator.

Take a photo of the location of the loops and wires|

Disconnect the refrigerator from the mains and defrost (if required)|

Release door from shelves and trays|

Prepare tools and a clean work area-->

Step 1: Removing the top hinge

1. Open the door 90° and support it a wooden block or book - this will prevent it from falling when unscrewing the screws.

2. Remove decorative plug on the top hinge (pry it up with a flat screwdriver).

3. Unscrew adjusting screw (usually located under the plug) and remember its position - after rehanging it will need to be returned to its original state.

4. Unscrew the remaining screws securing the hinge to the refrigerator body and carefully remove. it.

Step 2: Removing the lower hinge

1. Close the door and lift it upto remove it from the lower pin.

2. screws securing the lower hinge to the body. In models with hidden holes pre-remove the plugs on the opposite side.

3. Transfer the hinge to the other side using the existing holes or plugs.

Step 3: Transferring fasteners and plugs

1. Remove plugs from the opposite side (where the door will now be attached) and install them on the vacated holes.

2. If the new holes do not have threads, use thread lock (for example, Loctite) for reliability.

3. Install the hinges in new places, but do not tighten the screws all the way -adjustment will be required.

Step 4: Door installation and adjustment

1. Place the door on the bottom pin and align it vertically.

2. Secure the top hinge and adjust the clamp using adjusting screw (the door should close with light force).

3. Check gaps along the perimeter of the seal - they should be uniform (1-2 mm).

What to do if the door does not close tightly?

If after hanging the door does not fit tightly, the reasons may be as follows:

1. Incorrect adjustment of the hinges — loosen the top screw and correct the position.

2. Deformation seal —heat it with a hairdryer (temperature 50–60°C) and shape it with your hands.

3. Case distortion —check the level of the refrigerator and adjust the legs.

4. Nuances for models with a display and electronic control

Refrigerators Gorenje with a display (ORB153*, ORB173*) require a special approach due to the presence of power cables and opening sensors. Here are the key points:

• 📱 Disconnecting the cable: Carefully pull the connector out of the socket on the case. Do not pull on the wires - only on the plastic housing of the connector.
• 🔌 Moving the opening sensor: In some models, the sensor is attached to a loop. It must be moved to the new side without disturbing the position.
• 🔄 Display calibration: After connecting the cable, you may need to reset the settings through the menu Settings → Factory Reset.

In models Gorenje ORB173 and ORB153 after re-hanging the door, you must update the firmware through the service menu, otherwise the display may display an error Err 04 (mismatch of sensor positions). Update instructions are usually attached to the documentation or available on the website manufacturer.

If after re-hanging the display does not turns on:

1. Check polarity of the cable connection (usually marked in red or white).
2. Make sure contacts are not dirty - wipe them with alcohol.
3. Do hard reset: unplug the refrigerator for 5 minutes.

⚠️ Attention: In refrigerators with the function SmartCool (for example, Gorenje RK 6292 AW) after re-hanging the door, the temperature zone settings may be lost. Check the readings after a day and, if necessary, recalibrate.

5. Typical mistakes and how to avoid them

Even if you follow the instructions, you can make mistakes that will lead to loose closure, creaking hinges or electronics failure. Here are the most common mistakes:

• 🔩 Tightening the screws - leads to thread failure. Tighten the fastenings with a force of no more than 2–3 Nm.
• 🚪 Ignoring adjustment of hinges —the door may sag in a week. Always check the vertical level.
• 🔌 Incorrect connection of the cables —in 30% of cases it causes display errors. Use a marker to mark the position of the connectors.
• 🧊 Working with the refrigerator on —risk of short circuit when the tool comes into contact with the electronics.

One of the most insidious mistakes — unaccounted for hidden fastenings. For example, in the model Gorenje NK 6191 under the bottom hinge there is an additional screw that holds door shock absorber. If you do not move it, the door will close with a bang.

Another point - sealing rubber band. It is easy to damage during dismantling. If, after rehanging, you notice that the elastic band comes off in the cornerheat it with a hairdryer (not higher than 60°C) and press it for 10-15 minutes with a heavy object (for example, a book).

6. Checking the result and final settings

After rehanging the door, perform the required checks:

1. Leak test: Place a sheet of paper between the seal and the body. If it falls out, the hinges need to be adjusted.
2. Checking the level: Use a bubble level to make sure there is no distortion.
3. Display functionality (if any): Make sure all indicators are working and there are no errors type E1 or Err.
4. Noise test: Open and close the door several times - creaking or knocking indicates incorrect installation of the hinges.

If the refrigerator equipped with a system NoFrost, after reversing the door the fan noise may temporarily increase. This is normal - the system redistributes the air in the new position. The noise should disappear after 12–24 hours.

For models with ice maker (Gorenje RK 6292 AW) additionally check:

• Integrity water supply hose —it should not bend.
• Position water level sensor —it is attached to the door and can get knocked down.

⚠️ Attention: In refrigerators with inverter compressor (series ORB) after re-hanging the door, it may be necessary to restart the cooling system. To do this, unplug the device for 10 minutes, then turn it on again.

7. When is it better to contact a specialist?

Despite the apparent simplicity, in some cases it is better to entrust the door hanging to a professional:

• 🔧 If your model is over 10 years - the plastic and rubber bands could have lost their elasticity, and an attempt to hang them will lead to damage.
• ⚡ If the refrigerator is on guarantees - independent repair can void it.
• 📱 If an error appears after re-hanging E5 or Err 03 —this indicates a problem with the electronic unit, which cannot be eliminated without diagnostics.
• 💧 If in a model with ice maker after rehanging, water stops flowing, the hose or sensor may be damaged.

The cost of the service for re-hanging the door in service centers Gorenje ranges from 1,500 to 3,000 rubles (for 2026), depending on the model and region. If you are not confident in your abilities, compare this amount with the cost of possible repairs in case of an error.

Also contact a specialist if, after re-hanging yourself, you notice:

• Increase energy consumption (the compressor works without stopping).
• Appearance condensation on the walls or seal.
• Spontaneous opening doors.

FAQ: Frequently asked questions about reversing the Gorenje door

Is it possible to rehang the door of a Gorenje refrigerator with a display yourself?

Yes, but special care is required when working with cables and sensors. In models ORB153 and ORB173 after rehanging, you may need to update the firmware through the service menu. If you are not sure, it is better to contact the service.

What to do if, after rehanging, the door does not close tightly?

The reasons may be different:

1. Incorrect adjustment of the hinges - loosen the top screw and adjust the position.
2. Deformation of the seal - warm it up with a hairdryer (50–60°C) and shape it.
3. The case is skewed - check the level of the refrigerator.

If the problem persists, check if something is preventing it from closing (for example, display wires).

Do you need to defrost the refrigerator before re-hanging the door?

Required if you have a model with drip system (not NoFrost). Otherwise, when the housing is tilted, water from the drainage system may flood the compressor. For NoFrost defrosting is not required, but the refrigerator must be unplugged.

How long does it take to hang the door?

On average - from 40 minutes to 2 hours, depending on the model:

• Budget models (Gorenje RK) - 40–60 minutes.
• Models with hidden hinges (Gorenje NRK) - 1–1.5 hours.
• Refrigerators with display (Gorenje ORB) - up to 2 hours (including work with electronics).

If you are doing this for the first time, allow yourself some time - there may be hiccups with adjustment.

Is it possible to reverse the door on a Gorenje refrigerator with a French door?

Yes, but this is more difficult due to the need to simultaneously rehang both leaves. You will need:

1. Dismantle both doors.
2. Move the hinges and fastenings for the middle lintel.
3. Adjust the pressure of each leaf separately.

It is almost impossible to cope without an assistant - one door must be fixed while hanging second.