Changing the side of the door opening is one of the most popular operations during installation household appliances in a new kitchen. Often the standard factory configuration, where the handle is located on the right, does not fit into the layout of the room or interferes with easy access to other cabinets. Owners of refrigerators Hisense can independently change the hinge if the model provides such an opportunity. This does not require calling a specialist, but requires accuracy and the availability of a basic set of tools.
Before starting work, it is important to understand that the design of refrigerators Hisense may differ depending on the series and year of manufacture. In models with a display on the door or a NoFrost system with a complex duct system, the procedure may be limited or require turning off the electronics. If you are not confident in your abilities, it is better to enlist the help of a second person, since the doors are heavy and have glass shelves that can fall out if handled carelessly.
Next, we will analyze a step-by-step algorithm of actions that will help you safely dismantle and install the hinges. Compliance with the sequence of operations will avoid damage to the housing and disruption of the seal. Carefully read the instructions before you pick up a wrench.
Preparation of tools and workplace
The success of the operation depends 90% on proper preparation. You don't need complex specialized equipment; a standard home craftsman's kit is enough. The main thing is to ensure the stability of the unit, since when removing the top hinges the refrigerator may lose balance. Clear the space around the equipment by at least one meter on all sides.
For work you will need the following tools:
- 🔧 A set of screwdrivers (phillips and flat) for removing decorative plugs.
- 🔩 8 mm wrench or socket (most often used c Hisense).
- 🧤 Work gloves to protect your hands from sharp metal edges.
- 🧼 Soft rags for wiping the attachment points.
Be sure to disconnect the refrigerator from the power supply before starting any manipulations. This is a basic safety rule that cannot be ignored, even if you are only working with. mechanical parts. In some models, wiring may pass through loops, and accidental damage to the insulation is dangerous.
⚠️ Attention: Make sure the floor under the refrigerator is level and dry. If you are working on slippery linoleum or tiles, place a non-slip material under the legs of the unit or have an assistant hold the cabinet.
Dismantling the top hinge and removing doors
The process starts from the top of the refrigerator compartment. This is where the main supporting hinge is attached, which holds the weight of the door. First, you need to remove the decorative hinge cover. Usually it is held on by latches or one screw hidden under a sticker or plastic plug.
After removing the cover, you will see. fastening bolts. Do not unscrew them completely at once - loosen until the door begins to move. Important: before the final unscrewing of the bolts, the upper door must be held by an assistant or a special stop, otherwise it may fall and damage the floor or zichzelf. Hisense a system is often used where the hinge is fixed with two or three bolts.
Algorithm for removing the upper part:
- ❄️ Remove all shelves and contents from the refrigerator door to make the structure easier.
- 🔌 Disconnect the wire connectors if lighting or a display is connected to the door (carefully pull the chip, not the wires).
- 🔓 Unscrew the bolts securing the top hinge and remove the metal plate.
- 🚪 Remove the top door by lifting it up from the bottom hinge (if the design allows) or completely disconnecting it.
☑️ Ready for dismantling
If your model The refrigerator Hisense has a system NoFrost, be especially careful with the wires. They can be laid inside the case and only come out in the area of the top hinge.
Flipping the bottom door of the freezer
After removing the top door, the turn comes. freezer compartment. In two-chamber models Hisense the lower door is often attached to a separate hinge located in the middle of the body. The procedure is similar, but has its own nuances. The weight of the lower door is usually greater, so the help of a second person is required here.
First remove the decorative panel of the middle hinge (if there is one) and loosen the fasteners. The freezer door must be carefully removed, moving it to the side. Pay attention to the pins or bushings that may be in the hinge holes - they must be saved for reinstallation, but on the other side.
Now you need to turn the door itself over:
- 🔄 Place the door on a soft surface with the outer side down (lay it down). blanket).
- 🔩 Find the plugs for the holes for handles and hinges at the ends of the door.
- 🛠️ Unscrew the handle pin (if it is removable) or move the handle to the other side according to the instructions for your model.
- 🧩 Rearrange the plastic plugs on new places, closing the old holes.
⚠️ Attention: When moving the handle, make sure that it clicks into place. A loose handle can come off under load.
What to do if the handle cannot be removed?
In some Hisense models, the handles may be missing. non-removable or fastened with hidden screws under the decorative trims. If the handle does not give in, do not use excessive force - check for the presence of screws at the ends or bottom of the handle. Sometimes it is necessary to remove the entire outer panel of the door.
Scheme for installing hinges on the new side
The most critical step is installing the hinges on the opposite side. side. Refrigerators often come with spare bushings or pins, but sometimes you have to use the old ones by simply replacing them. The main thing is not to confuse the top and bottom, since the shape of the holes may differ. Hisense Replacement bushings or pins are often supplied, but sometimes you have to use the old ones and simply reposition them. The main thing is not to confuse the top and bottom, since the shape of the holes may differ.
Installation begins from the bottom up (or the middle one, if it serves as a support for the freezer). Insert the pin into the new hole, making sure it fits tightly. Then put on the freezer door. Check that the sealing rubber lies evenly around the perimeter.
Turnover action table:
| Element | Action | Nuance |
|---|---|---|
| Bottom hinge | Move to the opposite corner | Use new holes |
| Middle hinge | Dismantle and install mirror | Monitor the level |
| Top loop | Install last | Do not tighten all the way right away |
| Plugs | Move to old places | For aesthetics and tightness |
After installing the lower part, proceed to installing the upper door. Here it is important to correctly insert the pins into the holes of the middle hinge. If the holes do not match, the hinges may be skewed - loosen the fasteners and align the position.
Adjusting the position of the doors and the tightness of the fit
After assembly, it may turn out that the doors hang crookedly or do not fit tightly to the body. This is normal, since during dismantling the factory adjustment is lost. Adjustment This is done by loosening the fastening bolts of the hinges and aligning the leaf vertically. plane.
Use a building level, applying it to the end of the door. The gap between the upper and lower doors (if they are butted) should be minimal and uniform across the entire width of refrigerators. Hisense It is often possible to (fine-tune) the height of the legs of the refrigerator itself, which also affects the angle of the doors.
Check the tightness of the magnetic seal around the entire perimeter. The sheet of paper should be clamped by the door with the same force at any point. If the paper flies out freely in an area, it means there is a leak there. This can be corrected by heating the seal with a hairdryer (carefully!) or by adjusting the hinge.
⚠️ Attention: Do not overtighten the hinge bolts. This can lead to deformation of the metal body or breakage of the thread, which will make further adjustment impossible.
Checking operation and common errors
The final stage is testing. Plug in the refrigerator and let it work. Pay attention to the operation of the compressor: if the door is skewed, the motor may work longer than usual, trying to gain temperature due to loss of cold. Listen to the sounds of closing - there should be no impacts of metal on metal or creaks.
Common mistakes that beginners make:
- 🚫 Forgot to connect the wire connectors (the light does not light up, the display does not work).
- 🚫 Lost the pins or mixed them up in places.
- 🚫 The transport locks were not removed (if they were inside).
- 🚫 The seal was pinched during installation, and it turned outward.
If you notice that after a few days of operation there is water on the floor or ice on the walls of the chamber, it means there is a tightness broken. You will have to repeat the adjustment procedure. In most cases, the problem is resolved by re-aligning the top hinge.
FAQ: Frequently Asked Questions
Is it difficult to re-hang the door on a Hisense display refrigerator?
It is more difficult than on a regular model. You need to carefully disconnect the cables going to the display. It is important to remember or photograph the order in which the connectors are connected. If you are not confident in your skills in working with electronics, it is better to invite a specialist.
Are special tools required for NoFrost models?
No special tools are needed, but more caution is required. With NoFrost systems, cold air ducts may pass through the door. If removed carefully, the air duct or insulation may be damaged. Proceed smoothly.
Is it possible to rehang the door if it is glass?
Yes, if the model Hisense includes such an option. However, glass doors are heavier and require more careful handling. Make sure that your hinges are designed to withstand the increased load, although usually the design is identical to their metal counterparts.
What to do if the holes for the hinges do not match?
In 99% of cases, the holes are symmetrical. If they don't match, check to see if you mixed up the left and right side of the loop, or if you forgot to turn the loop itself over. In rare cases (very old or specific models), a revolution may not be possible.