Re-hanging the Candy refrigerator door: instructions with photos and nuances

Re-hanging the refrigerator door Candy is a task that many owners face when moving, kitchen renovation or just for convenience. Despite the apparent complexity, the procedure can be performed independently, without resorting to the services of a specialist. The main thing is to understand the design of a particular model, have the necessary tools at hand and follow a clear algorithm.

In this article we will analyze the process of hanging the door for refrigerators of Candy different series (including popular ones Candy CRU 1662, Candy CSB 1752 and others), pay attention to typical mistakes and give recommendations for setting up after installation. Let us separately dwell on the nuances that the manufacturer often keeps silent in official instructions - for example, how to avoid misalignment of the door or what to do if the fasteners do not coincide with the holes.

If your refrigerator Candy belongs to a series with electronic control (for example Candy Smart), check whether the overhang is blocked by software - some models require resetting settings after changing the door position. Read about this and other pitfalls below.

Preparation: tools and safety

Before you start work, make sure you have everything you need. Most tools can be found in a standard home craftsman's kit, but some items (for example, hex keys) may require purchase.

• 🔧 Screwdrivers: Phillips (PH2) and flat (3-5 mm) - for unscrewing screws and plastic plugs.
• 🔩 Wrenches: open-end or 10 mm socket (for attaching hinges).
• 🔧 Hex wrench (if your model Candy uses internal hex bolts).
• 🧲 Magnet or telescopic grip —for convenient removing fallen screws.
• 📏 Level (bubble or laser) - to check the evenness of the door installation.
• 🧴 Lubrication (for example, WD-40 or silicone) - for processing the hinges after rehanging.

Important: if your refrigerator is Candy equipped with water dispenser or electronic display on the door, additional care will be required when working with wires. In some models (for example Candy CBCS 1852), the display power cables run inside the door panel - they should not be kinked or pulled.

⚠️ Attention: before starting work unplug the refrigerator and wait until the internal temperature is equal to room temperature (about 1-2 hours). A sudden change in the position of the door on a hot compressor can lead to a malfunction of the system. data-i="83">With dispenser No Frost.

Determine the type of door fastening in your model

Refrigerators Candy use three main types of hinges, on which the hanging process depends:

1. Standard hinges with screws (the most common option, for example, in Candy CRU 1662).
2. Hinges with a lower hinge (found in models with No Frost, for example, Candy CSB 1752).
3. Hidden hinges (used in premium series, for example Candy Grand).

To determine the type, inspect the top and bottom of the door:

• 🔍 If you can see plastic plugs on the side walls of the refrigerator - you have standard hinges.
• 🔍 If there is a metal pingoing into the body, this is a hinge system.
• 🔍 If the fasteners are not visible Completely hidden hinges (you will need to remove the decorative panel).

For models with hidden hinges a special tool may be required - plastic spatula to remove decorative panels. If you do not have one, use a flat screwdriver, wrapping its end with electrical tape to avoid scratching the coating.

Step-by-step instructions: hanging the door on standard hinges

Let's look at the process using the model as an example Candy CRU 1662 (similar for CSB 1752, CBCS 1852 and others with screws).

Step 1: Remove the door

1. Open the door 90 degrees and place a support under it (for example, a chair or a wooden block) so that it does not fall when unscrewing.
2. Remove plastic plugs from the side walls of the refrigerator (pry them off with a flat screwdriver).
3. Unscrew top hinge (usually 2-3 screws). Hold the door so that it does not move.
4. Carefully lift the door up and remove it from the bottom pin.

Step 2: Transfer the loops to the other side

• 🔧 Unscrew bottom loop and transfer it to the opposite side (the holes are already provided by the manufacturer and closed with plugs).
• 🔧 Install upper loop mirror relative to the original position.
• 🔧 If there are no holes for screws, use drill with a 3-4 mm drill, but be careful not to damage the internal ones refrigerant tubes.

Step 3: Install the door in a new position

1. Put the door on bottom pin and level it.
2. Secure upper hingebut do not tighten the screws all the way.
3. Check that the door opens and closes smoothly, without distortions.
4. Tighten all the fasteners and install the plugs in place.

Step 4: Checking and setting

After installation:

• 🔍 Check tightness of the seal —there should be no gaps of more than 1-2 mm between the door and the body.
• 🔍 Make sure that the door does not open spontaneously when tilting the refrigerator to 30–45 degrees.
• 🔍 If the refrigerator is with No Frost, run the test mode (if available) or let it run for 2-3 hours to check the tightness.

What to do if the door does not close tightly?

If after rehanging the door does not fit tightly, check:

- whether the hinge is skewed (use a level);

- whether the seal is caught between the door and body;

- are the screws loose (tighten them).

If the problem remains, you may need to adjust the hinges using a hex key (the instructions for the model indicate adjustment points).

Features of hanging the door in Candy refrigerators with No Frost

Models with the system No Frost (for example, Candy CSB 1752 or Candy CBCS 1852) have additional nuances:

1. Ventilation ducts: when hanging the door, do not block the holes for air circulation (usually located in the upper part of the refrigerator compartment).
2. Electronic control unit: in some models, when changing the door position, reset settings (hold the button Super Cool for 5 seconds).
3. Closing sensor: if the door does not close completely, check the position of the magnetic sensor (it may move when repositioned).

In refrigerators Candy No Frost 2020+ series lower The loop is often attached not to screws, but to latches. To remove it, you need to press the lock inside the hinge (use a screwdriver).

⚠️ Attention: if after rehanging the refrigerator Candy s No Frost began to make more noise or frost appeared on the back wall, the tightness of the system is most likely broken. In this case you need to return the door to its original position and contact the service center.

Typical mistakes and how to avoid them

Even if you strictly follow the instructions, you can make mistakes that will lead to problems. Here are the most common:

• 🚫 Door skew: occurs if the loops are tightened unevenly. Use a level and tighten the screws crosswise.
• 🚫 Damage to the seal: do not pull the door by the rubber gasket - it may tear or deform.
• 🚫 Forgotten plugs: if you do not transfer the plastic plugs to the new side, dust and moisture will get into the holes.
• 🚫 Ignoring wires: in models with a display (Candy Smart), the cables can be damaged if you do not disconnect them before removing the door.

Another common problem is the door does not close completely. Reasons:

• 🔧 The hinges are installed too deep (you need to unscrew the screws 1-2 turns).
• 🔧 The seal is dirty or deformed (wipe it with soapy water and lubricate silicone).
• 🔧 The refrigerator is not level (adjust the legs).

Adjusting the door after rehanging

Even if the door is visually level, it may need to be adjusted for a perfect fit. Here's how to do it:

1. Vertical adjustment (if the door sag)

To do this:

1. Loosen lower hinge (do not remove completely!).
2. Raise or lower the door to the desired level.
3. Tighten the loop back.

2. Horizontal adjustment (if the door touches the body)

Use hex key to tighten the eccentrics on the hinges (if they are provided in the model). Turn them clockwise to move the door away from the body, and counterclockwise to bring them closer.

3. Adjusting the seal

If the seal does not fit tightly:

• 🧼 Wipe it warm soapy solution and dry.
• 🔥 Warm up the rubber hairdryer (temperature 50–60°C) - this will restore its elasticity.
• 🛠 If the seal is deformed, replace it (the part number is indicated in the instructions for model).

To check the tightness, use test with a sheet of paper:

1. Insert a sheet between the seal and the body.
2. Close the door and try to pull out the paper.
3. If the sheet comes out easily - the seal needs to be adjusted or replaced.

Reversing the door in Candy Side-by-Side refrigerators

Models Candy Side-by-Side (for example, Candy CBCS 2052) have two doors, and the process of rehanging them is more complicated. Here are the key points:

• 🔧 Doors cannot be hung separately —only at the same time, otherwise the balance will be disrupted.
• 🔧 In the upper part of the body there is connecting strip, which also needs to be move.
• 🔧 The hinges in these models are often attached to hexagon socket bolts (a 5 mm wrench is required).

Algorithm steps:

1. Remove decorative top panel (it hides the fastenings of the connecting strip).
2. Unscrew the strip and move it to the other side.
3. Remove both doors, starting with refrigerator compartment.
4. Move the hinges and install the doors in a new position.
5. Adjust the position of the doors relative to each other (the gap between them should be 2-3 mm).

⚠️ Attention: in models Candy Side-by-Side with ice generator before re-hanging, you must turn off the water supply and drain the residue from the system (otherwise a leak may occur when removing the door).

FAQ: Frequently asked questions about re-hanging the Candy refrigerator door

Is it possible to hang the door on the Candy refrigerator yourself if you have no experience?

Yes, but start with simple models (for example, Candy CRU 1662). The main thing is to take your time and follow the instructions. If you have a model with hidden hinges or an electronic display, it is better to invite a specialist.

What to do if the door does not close after rehanging?

Check:

• The levelness of the hinges (use a level).
• Condition seal (it may be dirty or deformed).
• Tightening the screws (they may be loosened).

If the problem persists, return the door to its original position and contact service.

Is it necessary to defrost the refrigerator before re-hanging the door?

No, but unplug it required. If the refrigerator is equipped with No Frost, wait until the temperature inside is equal to room temperature (1-2 hours).

Is it possible to hang the door on a Candy refrigerator with a water dispenser?

Yes, but you will need to carefully disconnect the hoses water supply and transfer them to the other side. In some models (Candy Smart), to do this you need to remove the back cover of the case.

How much does it cost to rehang the door of a Candy refrigerator in the service?

The cost depends on the model and region, but on average:

• Standard hinges: 1500–2500 rubles.
• Hidden hinges or Side-by-Side: 3000–5000 rubles.

Independent re-hanging will only cost the cost of the tools (if they are not at hand).