How to hang the door of an LG refrigerator with a display: complete instructions

Modern refrigerators LG with displays on the door are complex engineering structures that require a delicate approach when reinstalling. Unlike classic models, where the process takes 15 minutes, here it is necessary to take into account the presence of electronic loops, magnetic locks and specific loop geometry. An error in the sequence of actions can lead to damage display panel or failure of the seal of the chamber.

Before starting work, it is critically important to determine the type of your unit, since the algorithm of actions for models with the system Door-in-Door and standard two-chamber refrigerators differs significantly. You'll need an assortment of tools, including Phillips screwdrivers, socket wrenches, and perhaps the help of a second person to hold the heavy blade. Carefully study the design of the hinges before you begin dismantling.

In this article we will analyze each stage in detail, paying special attention to the safety of electronics and the correct adjustment of gaps. Incorrect installation may result in the door not fitting tightly, causing ice to freeze, or damage to the control cable control cable.

⚠️ Attention: All work on dismantling the doors should be carried out only after the device has been completely disconnected from the power supply. Otherwise, there is a risk of a short circuit when disconnecting the cables.

Preparation of the workplace and the necessary tools

The success of the operation is 80% dependent on the correct preparation of the space around the refrigerator. You will need a clear area at least a meter wide on each side to be able to lay the removed door on a flat surface covered with soft material. Make sure the floor is stable and the lighting is bright enough to see small parts of the fasteners.

To complete the task you will need the following set of tools:

• 🔧 Phillips screwdriver (preferably with a magnetic tip).
• 🔩 Set of sockets (usually 8, 10 or 13 mm).
• 🧤 Work gloves to protect your hands from sharp metal edges.
• 📦 Plastic container for folding screws.
• 📄 Manufacturer's instructions (for your specific model).

Pay special attention the presence of a soft backing. The door leaf with a display LG has significant weight, and it is strictly forbidden to place it on a hard floor or tile. Use a blanket, blanket, or cardboard box laid out on the floor. This will prevent the appearance of dents on the case and cracks on display.

Removing the top panel and disconnecting the electronics

The first step is always to remove the top cover of the refrigerator, which hides the main fasteners of the top hinge. In models LG it is usually fixed with two screws at the front and latches at the back. Carefully unscrew the screws and slide the cover back until it disengages.

After removing the cover, you will see the top hinge and the wires that go to it. Here is display cablewhich connects the control panel on the door to the main control unit inside the case.

• 🔌 Find the cable connector (usually a white or blue connector).
• 👆 Gently press the connector latch if it yes.
• 🔄 Smoothly pull the connector up, avoiding tugging on the wires themselves.

Do not try to disconnect the cable by pulling the wires - this is guaranteed to lead to broken contacts. If the connector does not budge, check for an additional stopper. After disconnecting, remove the wires inside the housing or secure them so that they do not interfere with further work. Now access to the top hinge bolts is open.

What to do if the cable does not turn off?

If the connector cannot be removed with light force, do not use force. Inspect it with a flashlight: perhaps the plastic antennae are in the way or you need to press the latch on both sides at the same time. In rare cases, the connector may be glued with heat shrink, which must be carefully cut with a scalpel.

⚠️ Attention: The cables in refrigerators LG are very thin and sensitive. Do not bend them at an acute angle and do not allow moisture to get on the contacts.

Removing door handles and dismantling the top panel

On many models of refrigerators LG the handles are attached not only from the outside, but also have internal screws hidden under decorative plugs. To remove the handle, find these plugs (often they are located on the bottom or side of the handle), pry them off with a thin screwdriver and unscrew the mounting bolts.

Now you can proceed to removing the top door. Since we are working with a model that has display, the weight of this section can reach 20-25 kg. It is difficult and dangerous for one person to cope. Ask an assistant to hold the door while you unscrew the top hinge bolts.

Removal sequence:

• 🙌 The assistant holds the door firmly so that it does not fall after removing the bolts.
• 🔩 You unscrew all the bolts holding the upper hinge.
• 🚪 Carefully remove the hinge and set it aside.
• 📉 With the help of an assistant, remove the door from the lower hinge and lay it on the prepared substrate.

After removing the door, inspect the fastening points. There may be bushings or plugs that will need to be moved to the opposite side. Keep all removed parts in one place so as not to lose them during the process.

Rehanging the lower panel and working with hinges

After removing the top door, access to the middle hinge (if the refrigerator is three-chamber) or directly to the bottom door opens. The principle of operation is similar: unscrew the bolts, hold the door, remove it. However, there is a nuance here: it is often necessary to rearrange the axes or bushings inside the hinge itself.

Carefully inspect the design of the hinge. In some models LG the rotation axis is asymmetrical, and to rehang it you need to turn it over or move it to another hole. If this is not done, the door will be warped and Tightness break. Use the table below to check the configuration of your model.

After removing all the panels, it is necessary to remove the lower hinges from the refrigerator body. They are attached to the floor of the device. Clean the holes from dust and metal shavings that may have accumulated during operation. This is important so that the new bolts lie flat.

Installing the hinges on the new side and installing the doors

Now we begin assembly in a mirror image. Install the bottom hinge onto the new side using the holes that were previously covered with plugs. Screw in the bolts, but do not tighten them all the way yet - this will allow you to adjust the position of the door when hanging.

Place the bottom door onto the hinge axis. Make sure she sits up straight. Then install the middle hinge (if there is one) and hang the top door. At this stage, it is important to correctly pass display cable through the holes in the hinges and the case so that it does not twist or be pinched by the metal.

Secure the top loop. Before final tightening, check the vertical installation of the doors using a building level. If the doors are skewed, loosen the fasteners and straighten the position. After this, you can finally tighten all the bolts and install the top cover of the refrigerator.

⚠️ Attention: When installing doors, watch the cable. If it is tense or twisted, it may tear when opening the door, which will lead to the display not working.

Rearranging the plugs and final adjustment

After installing the doors in place, holes from the hinges will remain on the free side. They must be closed with decorative plugs that came with the refrigerator (usually they are in the bag with the documents or were originally installed on the non-working side). If the plugs are lost, they can be ordered from the service center LG.

The final stage is adjusting the gaps. The doors must fit tightly to the body around the entire perimeter. If you notice that the door is moving away in one of the corners, use the adjusting screws on the hinges (if provided by the design) or pads. Also check the operation of the magnetic lock (if any) - it should latch with a characteristic sound.

Plug in the refrigerator. Check the operation of the display: are all indicators lit, is the sensor responsive. If the display does not turn on, check the tightness of the cable connection. You may need to remove the top cover again and reconnect the connector until it clicks.

Common mistakes and precautions

One of the most common mistakes is ignoring the weight of the door with a display. Trying to remove it alone, craftsmen often drop the structure, which leads to breaking display glass or deformation of the body. Always involve an assistant.

Another mistake is the loss of specific screws. Refrigerators LG often use bolts of different lengths for different components. If they are mixed up, the long bolt may rest against the plastic and split the hinge body, while the short bolt may not provide the required strength. Sort the fasteners immediately.

Also, do not forget about the floor level. If the refrigerator is positioned crookedly, even perfectly hung doors will open or close loosely on their own. Before starting work, align the legs of the refrigerator.

Is it necessary to change the opening side of the freezer separately?

In most two-compartment refrigerators LG the doors of the freezer and refrigerator compartments are hung together as a single unit or in series. Separate re-hanging of only one door is not possible on all models and requires removal of the intermediate partition, which is a complex procedure.

What to do if the display does not work after re-hanging?

First of all, check the cable connection. Make sure it is inserted all the way and locked. If everything is visually normal, try resetting the refrigerator by unplugging it for 10-15 minutes. If this does not help, the cable may have been damaged during installation.

Is it possible to rehang the door if the refrigerator is built into the kitchen?

For built-in models, the procedure is much more complicated, since it requires dismantling the facades and the appliances themselves from the niche. Often, re-hanging built-in refrigerators LG without completely removing them from the furniture is impossible due to limited access to the hinges.

Will the warranty remain valid after re-hanging the doors yourself?

According to the rules of many service centers, if during the process of re-hanging yourself you did not damage the components (did not tear off threads, the cable was not broken, the glass was not broken), the warranty on the compressor and main components is maintained. However, any damage that occurs during the work will not be covered under warranty.