The need to change the direction of opening the door often arises when moving or remodeling a kitchen space, when the standard configuration interferes with comfortable access to products. The equipment of the Russian brand Pozis was initially designed taking into account the possibility of such modernization, which greatly simplifies the task for the owner who does not have deep engineering knowledge. In most models, the designs of hinges and fasteners allow you to perform the procedure yourself, using only a basic set of home tools.
The process requires care and accuracy, since incorrect assembly can lead to skew of the canvas and disruption of the tightness of the seal. Re-hanging the door Pozis refrigerator usually takes no more than an hour, if you act strictly according to the algorithm and do not apply excessive physical effort where there is no need for it. It is important to prepare the workplace in advance, freeing up the space in front of the unit in order to have free access to all fastening points.
Before starting work, you must make sure that the refrigerator is disconnected from the power supply and completely defrosted, since the presence of ice or water inside can complicate manipulations. It is also worth enlisting the help of a second person, especially if we are talking about large two-chamber models, since the weight of the sash with shelves can be significant. Compliance with safety precautions and sequence of actions guarantees that your Pozis refrigerator after the alteration will function flawlessly.
Preparation of tools and workplace
The quality of work directly depends on the availability of a suitable tool, which must be in good working order and easy to use. To dismantle and subsequently install the elements, you will need a set horn keys or heads, since the hinge fastening bolts often have a specific head geometry. In some cases, you may need a flat or Phillips screwdriver to remove decorative plugs and plastic controls.
It would be a good idea to prepare a container for storing small parts such as screws, washers and bushings, so as not to lose a single element during the assembly process. Tools it is better to lay it out on a clean surfaces next to the refrigerator in order to have instant access to them and not be distracted by searching in the midst of the process. If the hinges are rusty or stuck, stock up on penetrating lubricant in advance, which will help loosen the connection without the risk of stripping the thread.
⚠️ Attention: Make sure that the floor under the refrigerator is dry and clean, as a fallen part or tool can scratch the floor covering or damage the legs of the unit when careless movement.
Organizing the space around equipment is critical to prevent injuries and damage to the device itself. Remove all foreign objects, rugs and furniture to ensure a clear all-round view and the ability to approach the refrigerator from any side. This is especially true when working with heavy doors that require space for maneuver when removing.
☑️ Checking readiness for work
Dismantling the top hinge and removing the door
The process should always start from the top of the structure, since that is where the main support unit is located, supporting the weight of the door leaf. First you need to remove the decorative cover that hides the fasteners; it is usually secured with latches or a small screw that requires careful handling. After gaining access to the mechanism, you need to loosen, but not yet completely unscrew the bolts of the upper hinge, so that the door does not fall sharply.
The next step is to carefully remove the door from the lower support, which will require reliable fixation of the door leaf in a vertical position while unscrewing the upper bolts. Upper hinge removed together with the fasteners and set aside, and the door itself is set aside the door is carefully removed onto a prepared soft surface so as not to damage the seal or internal coating. If the model is equipped with an opening sensor, you must first disconnect the electrical connector, being careful.
- 🔧 Remove the decorative plug from the upper end of the case.
- 🔩 Loosen the mounting bolts of the upper support hinge.
- 🚪 Remove the door from the lower axis and put it in a safe place.
- ⚡ Disconnect the door opening sensor connector, if provided by the design.
When working with two-chamber models, the sequence of actions may be slightly different, since it is often necessary to remove both leaves. In such cases, first the upper door of the freezer compartment is dismantled, then the lower door of the refrigerator compartment, which allows access to the intermediate partition and re-hanging mechanisms. Dismantling It should be done smoothly, without jerking, so as not to deform the metal elements of the case.
What to do if the bolts do not unscrew?
If the fasteners are rusty and cannot be wrenched, do not use excessive force, which could break the bolt. Treat the connection with penetrating lubricant, wait 10-15 minutes and try again, lightly tapping the key to destroy the oxides.
Transferring hardware elements and plugs
After removing the door, it is necessary to transfer all functional elements to the opposite side, including handles, stops and mating parts of locks. On the free side, the holes are closed with special plastic plugss, which usually come with the refrigerator or are already installed on the back side and require rearrangement. It is important to preserve the aesthetics of the product, so all screws must be tightened tightly, but without overtightening, so as not to damage the plastic.
Door handles can have different fastening designs: in some models they are fixed with screws from the bottom or top, in others they require partial disassembly of the inner panel. Fittings must be installed symmetrically relative to the factory position to ensure ergonomic use and visual harmony. If there is no threaded hole at the site where the handle will be installed, you may need to use spare holes closed with plugs.
Particular attention should be paid to the pins and bushings that ensure correct positioning of the door relative to the body. They must be moved to the new side, observing the orientation, since incorrect installation can lead to the door opening spontaneously or, conversely, too tightly. Installation symmetry guarantees a long service life of the seal and correct fit of the sash.
The process of transferring elements requires attention to detail, since the loss of even a small washer can disrupt the balancing. All removed decorative elements must be carefully moved to new places, checking their tightness. Some models Pozis may require additional adapters, which are stored in a technical niche or in the packaging of the device.
Installation of the lower hinge and installation of the sash
Installation begins with installing the lower support unit on the new side, which must be secured as securely as possible, since it takes on the main load. Bottom hinge fixed with standard bolts, it is important to ensure that it is not skewed relative to the horizontal, otherwise the door will be crooked. After securing the support, you can begin to place the door leaf in its place.
The door is carefully placed on the lower axis, after which it is aligned vertically for subsequent fixation of the upper part. At this stage, the participation of an assistant is critically important, who will hold the door in the desired position while you are fastening the upper elements. Installation should be done without haste, with constant checking of the gaps between the door and the refrigerator body.
| Work stage | Required tool | Key action |
|---|---|---|
| Installing the bottom | Open-end wrench, screwdriver | Fixing the support sleeve |
| Door hinge | Assistant, rags | Hit the lower axis |
| Fastening the top | Set of keys | Tightening the hinge bolts |
| Final adjustment | Level, key | Alignment of gaps |
After the door is installed in place, it is necessary to tighten the bolts of the upper hinge, but not yet all the way, so that there is a possibility for final adjustment of the position. Fastening elements tighten evenly, crosswise, to avoid distortion of the metal plate of the hinge. Only after making sure that the door is level and nothing interferes with its movement can you make the final tightening.
Adjusting the position and checking the tightness
The final and, perhaps, the most important stage is adjusting the position of the door, which ensures a tight fit of the seal around the entire perimeter. If the door is skewed, cracks may form in the corners through which cold will escape, causing the compressor to work harder. To correct the position, adjusting screws or spacers are used, as well as changing the height of the legs of the refrigerator itself.
Checking the tightness is carried out using a simple but effective method: clamp a sheet of paper between the door and the body at different points of the perimeter and try to pull it out. If the paper comes out too easily or, conversely, breaks, it means additional adjusting the hingesis required. In some cases, a slight tilt of the refrigerator body back helps, which facilitates the automatic closing of the door under the influence of gravity.
⚠️ Attention: If small gaps remain after adjustment, do not rush to bend the metal. Give the seal a few hours to straighten out - perhaps it was simply deformed during transportation and will take the desired shape.
Make sure that the door opens and closes smoothly, without creaking or jamming, and that the magnetic tape sticks to the body with a characteristic sound along its entire length. Tightness is the key to the correct temperature inside the chambers and saving energy, Therefore, this aspect should be given maximum attention. If leaks are detected, you can heat the seal with a hairdryer at a low temperature to make it more elastic.
Features of models with a display and No Frost
Owners and owners of modern models Pozis with a system No Frost and an electronic display should be especially careful when moving the door. The presence of air channels in the door leaf requires caution during dismantling so as not to damage the internal partitions and insulation. In addition, the power cables for the display and control buttons can be quite short, which limits the range of action when removing the shutter.
When working with electronics, be sure to disconnect the refrigerator from the network in advance to avoid short circuits in the control circuits. Cables you need to disconnect them by holding them by the plastic connectors, and not by the wires themselves, since The contacts are very fragile. If the control cable passes through the loop, it must be carefully removed from the channel before completely removing the door.
- ❄️ The No Frost system requires careful handling of the cold air supply channel.
- 🔌 Electronic modules are sensitive to static electricity and surges voltage.
- 🧵 Display cables often pass inside the loop and require careful removal.
- 🛡️ Protective shields on the wires must be installed in place after assembly.
After assembly, check the operation of the display and buttons, making sure all functions work correct. If the screen does not light up, check the tightness of the connectors that may have come loose during the installation process. Complex models may require resetting the settings after a power failure, so check the instructions for your specific device.
Is it possible to damage freon tubes when re-hanging?
During the standard procedure for re-hanging doors, there is no access to the copper pipes of the refrigerant circuit, since they are laid inside the body or in the rear part. The risk arises only from rough mechanical impact with sharp tools in the hinge area, so work carefully.
Frequent errors and ways to eliminate them
Even with instructions, inexperienced users often make common mistakes that can negate all efforts. One of the most common problems is overtightening of bolts, which leads to thread deformation or breakage of plastic bushings. Excessive force When tightening, it does not add reliability, but only creates stress in the metal, which over time can lead to cracks.
Another common mistake is ignoring the level tilting the refrigerator, which leads to the door not closing tightly. If the unit stands strictly vertically or tilted forward, the door will open on its own, disturbing the temperature regime. It is necessary to make sure that the front legs are twisted a little more than the rear ones, creating the necessary slope back.
Also, users often forget to rearrange the stops or install the plugs incorrectly, leaving the holes open. This not only spoils the appearance, but also breaks the thermal insulation, allowing warm air to penetrate inside. Carefully checking all stages of assembly helps avoid the need to disassemble the structure again.
⚠️ Attention: The design of the hinges and the location of the holes may vary slightly depending on the year of manufacture of the model. Always check the visual inspection of a specific unit, and not just the text description.
If after all the manipulations the door still does not fit tightly, try replacing the seal or checking the geometry of the door itself for manufacturing defects. Sometimes it helps to lubricate the rubbing surfaces of the hinges with graphite grease, which does not attract dust. Error elimination at an early stage it will save you time and products that could be spoiled due to poor sealing.
Questions and answers about rehanging doors
Do you need to completely defrost the refrigerator before rehanging?
Yes, this is a prerequisite. The presence of ice or water inside the chambers can lead to a leak on the floor when tilting or removing the door, and will also complicate the process due to a shift in the center of gravity of the products and shelves.
Is it possible to rehang the door of a Pozis refrigerator alone?
Technically, this is possible for small-sized single-chamber models, but for double-chamber refrigerators it is strongly recommended to involve an assistant. The weight of the door, along with the shelves and glass inserts, is significant, and holding it straight with one hand while working with the key is extremely difficult and dangerous.
What to do if the plugs for old holes are lost?
The plugs are usually symmetrical and are already installed on the opposite side of the door and body. You just need to remove them from there and move them to the free places. If they are lost, they can be ordered at the service center or selected universal analogues of a suitable diameter.
Does re-hanging the door affect warranty service?
Independent re-hanging of the door, provided for by the design and carried out without damaging the components, is not grounds for denial of the warranty. However, if in the process the hinges are broken, the glass is broken or the body is damaged, the warranty case for these damages will not be considered.
How can you tell that the door is adjusted correctly?
A correctly adjusted door, when opened 90 degrees, should not tend to slam shut or open further. With a slight push, it should be smoothly brought to a close with a magnet, and a sheet of paper, clamped around the perimeter, should be removed with a noticeable, uniform force.