Reversing the door of a Samsung refrigerator with a display: instructions with video and nuances

1. Preparation: tools and safety

⚠️ Attention: If the refrigerator is under warranty, re-hanging the door yourself may invalidate it. Check the conditions in the documents or with the official dealer. Samsung.

2. Dismantling the old door: step by step with photo

Start by disconnecting the refrigerator from the network. Even if the display is turned off, there may be voltage in the control circuits. Then free the door from all removable elements: shelves, containers and magnetic seals (they can not be removed, but they will interfere with the process). maneuvers).

Procedure:

1. Remove the top cover of the refrigerator (if there is one) - it is usually secured with latches or two screws under decorative plugs.
2. Unscrew the bolts of the top hinge (they may be hidden under plastic covers B). models Samsung RF26** the hinge is fixed with an additional locking screw on the side.
3. Carefully lift the door up to remove it from the lower hinge. Do not pull the door towards yourself - this may damage the cable display! It is better to work with an assistant.
4. Place the door on a soft surface (for example, a blanket) with the display facing up so as not to damage the glass.

At this stage, many people encounter a problem: the door “jams” when trying to remove it. Reason - incomplete unscrewing of the bolts or dirty hingesIf the door does not budge, check:

• 🔩 Are all the bolts unscrewed (sometimes the bottom hinge has a hidden screw under the plug)
• 🧴 Are there any hinges of dried grease or rust (clean with WD-40)
• 🔄 Are you lifting the door correctly - strictly vertically, without distortions

3. Working with the display: disconnecting and connecting wires

The most important stage is working with the electronic module. In models Samsung with a display (series Family Hub, RF28** etc.) the door contains:

• 🔌 Main power cable (powering the display and sensors)
• 📶 Antenna cable (for models with Wi-Fi and SmartThings)
• 🔄 Control cable (connects the display to the main board)

To get to connectors:

1. Remove the decorative display panel. It is secured with latches - pry it off from the side with a plastic spatula (starting from the bottom corner).
2. Disconnect all connectors, having first photographed their location. Pay attention to color marking and the direction of the plugs (usually there is a white one). marker).
3. If the model has NFC module (for contactless control), its cable also needs to be disconnected, but do not pull it out completely - just loosen the latch.

Attention to detail:

• 🔹 The connectors can be secured with plastic latches - press them carefully so as not to break them.
• 🔹 In some models (Samsung RS68A**) the display cable goes through a loop - it needs to be pulled out of the groove before rehanging.
• 🔹 If there is oxidation on the contacts, clean them with alcohol and dry them.

After rehanging the door, connect the connectors in the reverse order. Do not turn on the refrigerator right away! Check first:

• 🔌 Are all cables connected tightly (without play)
• 📱 Are there any kinks in the cables (especially at the loops)
• 🔄 Does the orientation of the connectors coincide with the original (check the photo)

⚠️ Attention: If after connection the display does not turn on or blinks, do not panic. In 80% of cases, the problem is solved by rebooting again (unplug the refrigerator for 5 minutes). If this does not help, check the antenna cable contact (a common mistake when re-wiring).

4. models

Hinges in refrigerators Samsung may vary depending on the series. Below is a comparison table for popular models with a display:

General rehanging algorithm:

1. Move the hinges to the opposite side (the holes for them are usually closed with plugs).
2. Install the door on the new lower hinge, then fix the top one.
3. Adjust the position of the door vertically and horizontally (there are special grooves in the hinges for this).
4. Check the tightness of the seal - if there are gaps, tighten the bolts.

Tip: If after rehanging the door sag, do not rush to tighten it bolts. First check if the seal is in the way - sometimes it needs to be slightly bent. In models Samsung RF** a hexagon is used for adjustment (the hole is hidden under a plug on the hinge).

5. Setting up the display after rehanging

After the mechanical part of the work, the refrigerator needs to be “trained” to the new configuration. In models with a display (Family Hub, RF28** etc.), this is done through the service menu. Instructions:

1. Plug in the refrigerator. A message may appear on the display "Door Position Error" —this is normal.
2. Press the "Power Cool" and "Fridge" buttons simultaneously for 5 seconds to enter the service mode.
3. In the menu, select an item "Door Setting" (or "Door Reverse" depending on the model).
4. Confirm changing the door position (usually with the "OK" or "Select").
5. Wait for reboot (may take up to 2 minutes).

If after these steps the display does not work correctly (does not respond to touches, shows errors), reset the settings:

Press and hold "Ice Type" + "Water" for 10 seconds → select "Reset" → confirm.

In models with Wi-Fi (Samsung Family Hub) after re-hanging, you may need to reconnect to the network. To do this:

• 📶 Go to Settings → Network → Wi-Fi connection.
• 🔄 Select your network and enter the password again.
• 📱 Check the application. SmartThings (sometimes a restart is required).

⚠️ Attention: In refrigerators Samsung 2020–2023, after re-hanging the door, the calibration of temperature sensors may be reset. During the first day, monitor the indicators on the display - if they differ from the real ones (check with a thermometer), recalibrate in the menu "Temperature Control".

6. Checking and troubleshooting

After completing the work, carry out testing:

• 🔹 Closing tightness: place a sheet of paper between the door and the body. If it falls out, the hinges need to be adjusted.
• 🔹 Display operation: check all functions - temperature display, response to touch, operation of the ice maker (if equipped).
• 🔹 Noise when opening/closing: creaking or knocking indicates improper installation of hinges or misalignment of the door.
• 🔹 Condensation on the seal: if it appears in the first hours, this is normal. If it lasts longer than a day, check the tightness.

Typical problems and solutions:

If after all manipulations the door still does not close tightly, use tightness test:

1. Turn on the flashlight and place it inside the refrigerator (on the shelf).
2. Close the door and turn off the light in the room.
3. If light leaks through the seal - adjustment is needed.

7. Video instructions for popular models

For clarity, we recommend that you familiarize yourself with the video tutorials. Below is a selection of proven videos with explanations:

• 📺 Samsung RB37J5*** (Side-by-Side):

  The video shows the nuances of working with a double door and reconnecting the freezer display. Pay attention to the moment of removing the middle partition (at 5:20).

• 📺 Samsung RF263*** (French Door):

  The author explains in detail how to move the hinges to the opposite side without damaging the display cable. A useful life hack is using electrical tape to secure cables when turning the door over (8:45).

• 📺 Samsung RS68A8*** (Family Hub):

  The most difficult case due to the large number of electronics. The video shows how to properly disconnect the antenna cable so as not to damage the Wi-Fi module (see 12:10).

Search tip: if your model is not in the list, look for the video by series code (for example, "Samsung RF28 rehang the door"). Pay attention to the publication date - in new models (2022 and later), the fastening of the hinges may differ.

Before repeating the steps from the video, check our instructions - some authors omit important details (for example, they do not show how to properly fix the display cable after rehanging).

8. When is it better to contact a specialist

Although re-hanging a door Samsung with a display is a completely doable task, there are situations when it is better to trust the professionals:

• 🔧 If during dismantling you damaged the display cable or connectors (exposed wires or cracks are visible on board).
• ⚡ After re-hanging, the refrigerator displays errors "11E", "21E" or "33E" —this indicates problems with the electronic module.
• 🔊 If an uncharacteristic noise appears (hum, grinding) - the compressor may have shifted when adjusting the loops or a fan.
• 💧 In the first day after re-hanging, ice forms on the back wall of the refrigerator - this is a sign of a violation of the system's tightness No Frost.

The cost of professional door re-hanging in service centers Samsung varies from 2,500 to 5,000 rubles (depending on the model and region). If you are not confident in your abilities, compare these numbers with the risk of damaging the electronics - sometimes savings turn into more expensive repairs.

How to choose a specialist:

• 🔍 Check reviews on Yandex.Services or Profi.ru (look for specialists with experience specifically c Samsung).
• 📄 Check if the work is guaranteed (minimum 3 months).
• 💰 Compare prices: the cost is too low (below 2,000 rubles) may indicate low qualifications.

⚠️ Attention: If your refrigerator is under warranty, and reversing the door is not provided for in the instructions as a user operation (check the section "Warranty" in the manual), self-repair will void the warranty. In this case, contacting the official service Samsung is the only option.

FAQ: Frequently asked questions