Changing the door opening side A refrigerator is a common necessity when remodeling a kitchen or purchasing new furniture. Equipment owners Beko often face the question of whether it is possible to change the attachment on their own without damaging the complex electronics and display. The answer is clear: yes, it’s quite possible to do it yourself if you follow the sequence of actions and safety precautions.
The process requires care, especially when it comes to models with electronic control modulelocated on the facade. Incorrect actions can lead to broken cables or damage to contacts, so before starting work it is important to prepare the necessary tools and free up space around the unit.
In this article we will analyze in detail the algorithm of actions for rehanging doors on refrigerators Beko various series. You will learn about the nuances of dismantling panels, moving hinges and, most importantly, the correct connection of the display wires so that the equipment continues to delight you with stable operation.
⚠️ Attention: Before starting any dismantling work, be sure to disconnect the refrigerator from the electrical network. Working with live electrical wiring is strictly prohibited and is life-threatening.
Necessary tools and workplace preparation
The success of the operation directly depends on the quality of preparation. You do not need a specialized professional tool, but the set should be complete so as not to be interrupted in the process. The main tool will be screwdriver or a set of screwdrivers with different attachments, since fasteners may differ in the type of slots.
In addition to the main tool, prepare a container for folding screws. Small parts tend to get lost at the most inopportune moment, and finding a specific bolt for a hinge Beko in a store can be difficult. A soft cloth or cardboard will also be useful to protect the floor and the coating of the door itself from scratches during dismantling.
The list of required equipment includes:
- 🛠️ Phillips screwdriver (PH2) and a flat-head screwdriver for removing the plugs.
- 🔧 Socket head 8 mm wrench or socket (often used for hinges).
- 🧤 Construction gloves to protect hands from sharp metal edges.
- 📦 Container or magnetic tray for fastening.
Pay special attention to organizing the space. The refrigerator must be moved at least a meter away from the wall to ensure access from all sides. If the model provides the ability to adjust the height of the legs, it is better to check their condition in advance, since after rehanging it may be necessary level adjustment tilting the body.
Removing the top panel and working with electronics
The most critical step for models with a display is removing the top cover. It is under it that the control unit connection point of the cables going to the screen is hidden. In refrigerators Beko the cover is usually fixed with several screws at the back and plastic latches at the front.
First, carefully pry up the decorative plugs if they cover the fasteners. After unscrewing the visible bolts, do not pull the cover sharply upward. First check to see if anything is blocking its movement. The plastic on older models can be fragile, so movements must be smooth and confident.
After removing the cover, you will have access to the electronic filling. It is important to remember or photograph the location of the connectors. The display cable is usually connected to the main board via a snap-on connector. To disconnect it, you need to carefully bend the latch and pull out the connector, holding on to its plastic part, and not to the wires.
⚠️ Attention: The display cables are very thin and sensitive to creases. When disconnecting them and then moving them, make sure that the bending angle is not too sharp, otherwise the conductive tracks inside may burst.
If your model is equipped with a camera inside or temperature sensors in the upper part, wires may also come from them. They must be disconnected in the same way. Some users prefer not to disconnect the wires, but simply carefully move the harness over the top, but when completely reversing the door, it is safer to completely release the structure.
What to do if the connector cannot be removed?
Do not use force. Carefully inspect the connector: there may be an additional tab that needs to be pressed, or a screw that holds the block.
Removing the refrigerator and freezer doors
After the upper part is freed from the electronics, you can begin to remove the doors themselves. The process begins at the top hinge of the main refrigerator door. In two-chamber models, first remove the top door, then the middle door (if any), and lastly the bottom freezer.
Unscrew the top hinge mounting bolts. Since the door is heavy, have a helper hold it to prevent it from falling and distorting the remaining fasteners. After removing the hinge, carefully lift the door and remove it from the bottom bushing. Place the door on a prepared soft surface with the outer side facing up.
Similar actions are carried out with the bottom door of the freezer. It is important here not to lose bushings washers, which may fall out during dismantling. On some models Beko hinge axes may be pressed into the door or body, which requires additional attention when removing.
- 🚪 Remove the handle from the door if it interferes with access to the fasteners (on some models).
- 🔩 Save all the removed bolts, even if they seem redundant.
- 🧹 Wipe the hinge installation areas from dust and old grease before reinstalling.
Now that the doors have been removed, you need to dismantle the mating parts of the hinges on the opposite side of the body. Unscrew the lower and upper fasteners on the side where you plan to hang the door. These holes will subsequently be closed with plugs.
☑️ Removing the doors
Transfer of fastening elements and fittings
At this stage, the physical transfer of structural elements occurs. Hinges that were removed from one side of the housing must be installed on the opposite side. The refrigerator often comes with special plugs for holes that become redundant after rehanging. Beko Often there are special plugs for holes that become redundant after rehanging.
Carefully inspect the removed door. It may also have holes for a handle or additional fasteners. If the door design is symmetrical, you may need to move the handle to the other side. To do this, unscrew the handle fasteners from inside the door and install it in the prepared holes from the opposite end.
The table below will help you navigate the transfer of the main elements:
| Element | Action | Where to install |
|---|---|---|
| Upper hinge | Dismantling | Opposite upper corner |
| Lower bushing | Rearrangement | Opposite lower corner of the door |
| Plugs | Replacement | Closing the old holes |
| Door stopper | Rearrangement | Into the hole on the new side |
Do not forget about door stop (magnet or mechanical lock), which is often located in the lower or middle part of the case. It must be unscrewed and screwed into a symmetrical hole on the other side. If this is not done, the door will not close tightly in the new position.
When installing the hinges in a new location, do not immediately tighten the bolts until they stop. First, attach them so that it remains possible to (adjust) the position of the door in height and plane. Full tightening is done at the very end, after checking the operation of the mechanism.
Installing the doors in a new location
The installation process is in reverse order: first, the lower door (freezer) is hung, then the upper one. Lift the lower door and slide its lower bushing onto the hinge pin attached to the frame. Make sure that the door sits evenly and nothing prevents it from closing.
Then install the middle hinge (if the model is three-chamber or two-chamber with a common partition) and hang the upper door of the refrigerator compartment. Align the holes in the end of the door with the fasteners of the top hinge. Insert the bolts and carefully tighten them, securing the door in a vertical position.
It is critical to check the geometry at this stage. The doors must fit tightly to the body around the entire perimeter. If you see gaps at the top or bottom, you may need height adjustment by tightening the refrigerator support legs or loosening the hinges to move them.
⚠️ Attention: If after installation the door does not fit tightly and there is misalignment, do not try to fix it by force. Loosen the hinge fasteners, level the door and tighten the bolts again.
Check the operation of the magnetic seals. They must ensure tightness throughout the entire circuit. A sheet of paper sandwiched between the door and the body must be removed with noticeable force. If the paper falls out freely, it means that the seal does not fit in this place.
Connecting the display and assembling the structure
Let's return to the electronics. Now that the doors are in their new location, you need to connect the display cable. The wires must be carefully routed through the top of the housing. Depending on the design Beko, the cable can pass inside a metal tube or through a special groove in the door body.
Be extremely careful with the length of the wire. When moving the door to the other side, the cable path may change. Make sure that the cable is not stretched into a string, but also does not dangle too much so as not to get caught between the rubbing parts when opening.
Connect the connectors to the control board, observing the keys and orientation. The connector should go in until it clicks or makes firm contact. After connecting, check the functionality of the display by turning on the refrigerator. If the screen lights up and shows the temperature, you have completed the most difficult part.
Put the top decorative cover in place. Secure it with screws and latches. Make sure that no wires are left pinched by the plastic, which could lead to future damage.
The final touch is to install plugs on the free holes from the hinges. They can be rubber or plastic. Carefully insert them into the holes to give the refrigerator an aesthetic appearance and protect the insides from dust.
Adjustment and checking the result
After complete assembly, you need to give the refrigerator time to stabilization if it has been defrosted, or simply wait 2-3 hours before loading with food. During this time, listen to the operation of the compressor and check if the door does not open spontaneously. Pay attention to the operation of the closer (if your model has one). When the opening angle is less than a certain degree, the door should close itself. If this does not happen, check the tilt of the body. Often the refrigerator needs to be tilted back a little so that gravity helps close it.
Pay attention to the work door closer (if your model has one). When the opening angle is less than a certain degree, the door should close itself. If this does not happen, check the tilt of the body. Often the refrigerator needs to be tilted back a little to allow gravity to assist in closing.
If you notice that after rehanging the door began to touch the shelves or containers inside, check their installation. Perhaps, when installing the hinges, the door sat a little deeper or higher, and the internal space shifted relative to the shelves.
If you find problems with tightness, try heating the seal with a hairdryer (at low temperature) or boiling water to restore its elasticity after deformation during installation. This often helps eliminate minor leaks.
Do you need to call a technician after rehanging the door?
If you have successfully completed all the steps, connected the cables and the refrigerator is operating normally, calling a technician is not required. However, if the display does not light up, errors are on or the door does not close tightly despite the adjustments, it is better to contact an authorized service. Beko.
Is it possible to rehang the door without disconnecting the display wires?
Theoretically, this is possible if the length of the cable is enough to carefully transfer the harness over the top. However, the risk of damaging thin wires during such manipulations is very high. Professionals recommend always disconnecting the connectors for the safety of electronics.
Why does the door slam after rehanging?
The slam may be caused by too strong a magnetic pull or a violation of the vacuum inside the chamber. Also check to see if the door is touching any protrusions on the floor or plinth. Sometimes adjusting the height of the front legs helps.
Where can I get plugs for the holes if they are lost?
Plugs usually come with the refrigerator, often attached to the instructions or packed in a bag with documents. If they are lost, you can order them at the service center or select universal furniture plugs of a suitable diameter and color.
Does re-hanging the door affect the warranty?
Re-hanging the door yourself does not void the warranty on the compressor and main components, unless the electronic components are damaged in the process or the integrity of the case is not compromised. However, if you damage the display cable, this case will not be considered under warranty.