Changing the layout of the kitchen or buying a new set often poses the task of rearranging large items to the owner of household appliances. The refrigerator Beko is no exception, and its door may interfere with easy access to shelves or work surfaces. Fortunately, the design of most modern models provides the ability to reinstall the blade from the right side to the left and vice versa.
This procedure does not require calling a specialist and can be done independently if you have a basic set of tools. Proper completion of all steps will preserve the product warranty and ensure that the chamber is sealed tightly. The main thing is to act consistently, without skipping the stages of preparing and dismantling the fittings.
During the work process, it is important to be careful, since the doors have significant weight and can be damaged if handled carelessly. Below we will look in detail at how to rehang the door of the refrigerator Beko, what nuances to take into account for different series and how to avoid common mistakes.
Necessary tools and preparation of the workplace
Before starting any manipulations with the design of the refrigeration unit, it is necessary to prepare the workspace. You will need a free area next to the equipment where you can temporarily put the removed parts. It is better to cover the floor with a soft material, for example, a blanket or cardboard, so that the enamel is not scratched when in contact with hard objects.
The set of tools should be selected in advance so as not to interrupt the process of searching for a screwdriver. Models Beko most often require Phillips screwdrivers of different sizes and a socket wrench, usually 8 mm. In some cases, you may need a flat-head screwdriver or a special hex wrench included in the kit.
- 🛠️ Set of Phillips screwdrivers (PH1, PH2) for case screws.
- 🔧 Socket wrench or 8 mm socket for hinge bolts.
- 🧤 Work gloves to protect hands from sharp edges.
- 📦 Container for folding small fasteners.
⚠️ Attention: Before starting work, be sure to disconnect the refrigerator from the power supply! This will protect you from accidental electric shock and prevent damage to the electronics in case of an accidental short circuit.
Make sure that there is an assistant nearby, since the refrigerator door Beko weighs quite a lot, and holding it with one hand when unscrewing the hinges is extremely difficult and dangerous. Also check for loose plugs for holes that will remain open after transfer.
Removing the top panel and handle
The reinstallation process begins from the top of the refrigerator compartment. Depending on the model Beko, the top cover can be secured with latches or screws. If the model is equipped with a top handle, it usually needs to be removed first to gain access to the fasteners.
Remove the decorative caps if they cover the bolt heads. Carefully unscrew the fasteners holding the top panel in place. After this, the panel can be removed, allowing access to the top hinge of the door. Be careful: there may be backlight or control wires running under the panel.
⚠️ Attention: If you find wires going to the top loop, do not pull them by force under any circumstances! Carefully disconnect the connectors, having previously photographed their position for proper assembly.
Now you need to remove the top hinge itself. Unscrew the bolts that secure it to the refrigerator body, but do not remove it from the door yet if the design requires support from the canvas. In some models Beko the upper hinge is removed along with the door.
Removing the door and rearranging the bottom hinge
After freeing the upper part of the structure, the most crucial moment comes - removing the door leaf. A second person is definitely needed here. One holds the door, the second unscrews the bolts of the middle hinge (if there is one) or completely releases the leaf.
Carefully set the removed door aside in a prepared place. Now attention turns to the bottom loop. It must be removed from the right side and moved to the left. To do this, unscrew the fastening bolts from the bottom of the refrigerator body.
Install the bottom hinge to a new location using the holes provided by the manufacturer. Secure it with bolts, but do not tighten them all the way yet, so that the position is possible. Make sure that the thread goes in smoothly and does not break.
☑️ Checklist before installing the door
If your refrigerator is Beko two-chamber, a similar procedure must be carried out with the middle loop, which separates the freezer and refrigerator compartments. It is also transferred to the opposite side, changing the orientation of the pin, if this is structurally provided for.
Installing the door on the new side
When all the hinges are moved to the left side (or right, depending on the task), you can begin hanging the door. Carefully lift the fabric and place it on the pins of the bottom and middle loops. Make sure the holes line up perfectly.
Now you need to put the top hinge in place. Insert it into the grooves on the door and screw it to the refrigerator body. At this stage, the bolts are also not yet fully tightened. This is necessary for subsequent adjustment of the gaps.
- 🚪 Align the door holes with the hinge mounting pins.
- 🔩 Screw in the upper fasteners, providing support for the leaf.
- ⚖️ Check the vertical installation using a level.
- 🔒 Tighten all bolts completely after checking the progress.
It is important to check the tightness of the seal around the entire perimeter. If the door is skewed, the magnetic tape will not provide a tight seal, which will lead to ice freezing and increased energy consumption.
Adjusting the position and closing tightness
After installing the door in a new location, adjustment is often required. The gaps between the door and the body must be uniform over the entire height. If you notice a skew, you can slightly loosen the fastenings of the middle or lower hinge and align the position of the blade.
Pay special attention to the installation height. The door should not cling to the floor when opening, but too much gap at the bottom is also undesirable. Height adjustment is usually carried out by unscrewing or tightening the support legs of the refrigerator itself or the adjusting bolts on the hinges.
| Problem | Possible cause | Solution |
|---|---|---|
| The door does not fit tightly | Hinges are distorted or the seal is dirty | Adjust the hinges, wash the seal |
| It is difficult to open the door | The pressure is too strong or the vacuum | Check the height adjustment, wait 2-3 min |
| A squeak is heard | Metal friction or lack of lubrication | Lubricate the hinges with silicone grease |
| The door opens itself | Tilting the body back or weak magnet | Unscrew the front legs to tilt back |
⚠️ Attention: Do not use vegetable oil or WD-40 to lubricate the hinges! These substances can damage the plastic and rubber seal. Use only special silicone grease.
Do I need to wait before turning it on?
After moving the door and transporting the refrigerator (if it was tilted more than 45 degrees), it is recommended to wait 2-4 hours before turning it on. This is necessary so that the oil in the compressor flows back into the crankcase, otherwise the compressor may fail.
Transfer of controls and plugs
Many models Beko equipped with an electronic display or mode switches located on the door. When changing the opening side, these elements also need to be moved. Usually the wires are of sufficient length, but they may need to be carefully transferred to another channel.
The holes left from the previous installation of hinges and handles must be closed with decorative plugs. They usually come with the refrigerator and are in a bag with instructions. If the plugs are lost, you can order them at the service center or select analogs that match the color.
For models with a mechanical temperature controller located inside the chamber, it is often necessary to rearrange the plastic plug on the opposite wall. Remove the plug from the current side and install it in a new place, and close the hole with a new plug.
Checking functionality and typical errors
The final stage is a comprehensive check. Open and close the door several times, making sure that the movement is smooth, without jamming or extraneous sounds. Check the operation of the magnetic lock: the door should fit tightly around the entire perimeter.
Plug in the refrigerator and leave it running without load for several hours. Check to see if condensation or ice appears at the joints. This will indicate leakage problems that need to be corrected by adjustment.
- ❌ Error: Tightening the bolts until the door is installed in the correct position.
- ❌ Error: Ignoring the backlight wires during dismantling.
- ❌ Error: Using inappropriate ones tools that lick the bolt heads.
If you notice that the door Beko has begun to close worse than before the rearrangement, repeat the procedure for adjusting the hinges. Often a minimal displacement is enough to achieve an ideal result.
FAQ: Frequently asked questions
Is it possible to hang the door on a Beko refrigerator with the No Frost system?
Yes, the No Frost cooling system does not affect the ability to hang it. The hinge mechanism and the design of the body allow this procedure to be performed similarly to models with a drip defrosting system.
What to do if the holes for a new installation are not suitable?
In original refrigerators Beko holes for hanging are already provided by the factory. If you don't see the threaded holes on the correct side, it may be that your particular model does not support re-hanging or requires the installation of additional bushings from the kit.
Do you need to defrost the refrigerator before re-hanging?
Full defrosting is not necessary if you work quickly. However, if you are planning long-term work or washing the seal, it is better to turn off the device in advance to avoid water leaks and damage to the electronics.
Where can I get new plugs if the old ones are lost?
Plugs can be purchased at authorized service centers Beko, ordering them according to the model of the refrigerator. They can also often be found in online stores of spare parts for household appliances.