Rearranging furniture in the kitchen or changing the layout of the room often dictates its own conditions, forcing you to think about how to rehang the door in the refrigerator Biryusa. This process seems complicated only at first glance, but if you have basic tools and attention to detail, it is quite doable at home. Reweighing allows you to change the direction of opening the doors from left to right or vice versa, which significantly increases the ergonomics of the kitchen space.
Many owners are afraid to start work because of the risk of damage seal or breaking the seal, but the design of these units provides for the possibility of modification. It is important to understand that the procedure requires a sequence of actions and careful handling of fasteners to avoid distortions in the future. In this article we will analyze in detail all the stages, from preparation to the final adjustment of the gaps.
Necessary tools and preparation of the workplace
Before you begin dismantling, you need to make sure that you have a complete set of tools at hand. The absence of even one key element can lead to thread failure or damage to the plastic. To work, you will need open-end wrenches, a set of screwdrivers (Phillips and flathead) and, possibly, hexagons, if the hinge model requires it.
Particular attention should be paid to the stability of the unit itself. If you plan to work alone, make sure that the floor is level and the refrigerator does not wobble. Fixation The position of the equipment is the key to safety and maintaining the integrity of the compressor, which can be damaged if the housing is sharply tilted.
⚠️ Attention: Before starting any work, be sure to disconnect the refrigerator from electrical networks. This will prevent the risk of a short circuit if the wiring in the doors is accidentally damaged and will ensure your safety.
Prepare a container for small parts in advance so as not to lose screws and plugs. It would also be a good idea to invite an assistant, since removing a heavy bottom door with a freezer alone can be traumatic and physically difficult.
Removing the top door of the refrigerator
The process begins with dismantling the top door, since it has less weight and is easier to handle. The first step is to remove the decorative plug from the top hinge, if it is present on your model Biryusa. Usually it is pryed off with a flat-head screwdriver or simply removed by hand, allowing access to the mounting bolts.
Using the appropriate wrench, loosen, but do not completely unscrew the upper mounting bolts. At this moment, you need to hold the door so that it does not fall. After the bolts are loosened, carefully lift the door, removing it from the lower hinge axis, and set it aside.
☑️ Preparation for dismantling
Now you can completely unscrew the fasteners of the top hinge and remove the hinge itself from the refrigerator body. Pay attention to the condition of the gasket: if it shows signs of deformation, it may need to be replaced or softened with a hairdryer before installing it in a new place.
Removing the bottom door of the freezer
Removing the bottom part is a more labor-intensive process that requires caution. In some models Biryusa the freezer door is attached directly to the body through the middle hinge, which will also have to be rearranged. First, remove the handle or decorative trim that hides the fastening bolts.
Unscrew the middle hinge bolts while holding the bottom door. Here it is critical to prevent the sash from falling sharply, since it is heavier than the top one. It is best to perform this operation together: one person holds the door, the second operates the key.
After removing the door, disconnect the middle hinge from the body. If your model has a system automatic closing or a magnetic lock, be careful when unscrewing so as not to lose the spring mechanism or balls.
What to do if the bolts are rusty?
If the fasteners do not give in, do not apply excessive force force so as not to break the thread. Treat them with a penetrating lubricant (such as WD-40) and leave for 10-15 minutes. After this, try carefully moving it with a key.
Rearranging hinges and fittings
The most important step is reinstalling the hinges on the opposite side. The design of refrigerators Biryusa is symmetrical, so on the opposite side of the case there are already the necessary threaded holes, closed with plastic plugs. You need to unscrew the plugs from the working side and screw them into the vacated holes.
Move the loops to the new side. The upper loop is installed in its new place, but is not yet tightened tightly. The middle hinge (if there is one) is also transferred, but here it is important to correctly orient its pin, on which the lower door will be placed.
| Hinge type | Location (Standard) | Location (After overweight) | Fasteners |
|---|---|---|---|
| Top | Top right | Top left | 2-3 bolts |
| Middle | Center right | Center left | 2 bolts + axle |
| Bottom (support) | Bottom right (often hidden) | Left below | 1-2 bolts |
Don't forget to rearrange the handle if the design of your model Biryusa implies its relocation. To do this, remove the plugs from the holes for the handle on the new side and secure the handle with bolts. Old holes are closed with complete plugs.
Installing doors in a new place
After all the hinges have taken their new places, you can begin hanging the doors. Start with the bottom door (freezer compartment). Place the door onto the middle hinge pin, making sure it is level.
Then install the top door. Insert it into the top hinge and line up the mounting holes. At this stage, there is no need to tighten the bolts to the end; it is enough to simply tighten them so that the door holds, but has a slight play for adjustment.
Check the operation of the magnets and latches. The door should close tightly, without gaps, but not too tightly. If you feel resistance, the hinges may be installed askew or the height needs to be adjusted.
Adjusting the gaps and checking the tightness
The final stage is fine tuning. Adjustment necessary to ensure that the door fits evenly around the body around the entire perimeter. If you notice that the door is moving away in one corner, loosen the hinge fasteners and slightly change its position, then tighten the bolts again.
Pay special attention to the sealing rubber. After rehanging, it may not fit snugly right away. To eliminate gaps, you can use a hair dryer: heat the problem area of the seal with warm (not hot!) air and press the door until it cools. The rubber will become elastic and take the desired shape.
⚠️ Attention: Do not use open fire or too hot air from a hair dryer to straighten the seal. This can lead to melting of the plastic or loss of the magnetic properties of the rubber.
Check the horizontal installation of the refrigerator using a building level. If the floor is uneven, adjust the height of the front support feet. The correct tilt of the body back (about 2 degrees) ensures spontaneous closing of the door if it is released.
Frequently asked questions (FAQ)
Is it possible rehang the door if the refrigerator is built into the kitchen unit?
Technically this is possible, but extremely difficult. You will have to completely remove the refrigerator from the niche, remove the top panel of the cabinet (if there is one) and ensure easy access from all sides. In most cases, it is easier to call a technician or leave the door as is.
What to do if, after rehanging, the door does not stay closed?
Most likely, the angle of the refrigerator itself is broken. Make sure the front legs are turned out so that the body leans back. Also check if anything is preventing a tight fit (products on the shelves, packaging).
Do you need to defrost the refrigerator before rehanging?
Complete defrosting is not necessary, but it is recommended to remove all heavy products and shelves. This will reduce the weight of the structure and prevent the contents from falling out when tilted or vibrating during operation.
Where can I get plugs for the holes if they are lost?
A set of plugs usually comes in a bag with documents or is attached with tape to the inner surface of the refrigerator. If they are lost, you can order them at the service center Turkish or make them yourself from plastic of a suitable color.
Will the warranty remain valid after re-hanging yourself?
The re-hanging procedure itself is not a reason for refusal guarantees as long as you don't damage any parts in the process. However, if during dismantling the hinge is broken or the thread is torn off, this case will not be recognized as a warranty case. Proceed carefully.