Changing the layout on kitchen or the inconvenient location of the outlet often dictate their conditions, forcing you to think about rearranging large household appliances. Unit owners Beko may encounter a situation where the standard door opening on the right becomes an obstacle to the ergonomic use of space. Fortunately, the design of most modern models allows for the possibility of changing the opening side, which allows you to adapt the device to the individual requirements of the room.
This process does not require calling a specialist and can be done independently if you have a basic set of tools and attention to detail. Reversing the doors is a responsible procedure, as it requires careful handling of fragile fittings and heavy panels. Incorrect actions can lead to damage to the case or loss of tightness, so it is important to strictly follow the algorithm of actions.
Before starting work, you must clear the space around the refrigerator, ensuring access from all sides. Make sure you have someone to help you, as removing heavy door panels alone can be dangerous and could damage the floor or the unit itself. Below we will analyze in detail all the stages necessary for the successful modernization of your Beko.
Necessary tools and preparation of the workplace
High-quality preparation is the key to successful completion of the job without scratches on the floor and lost screws. You will need a standard home craftsman's kit, which can be found in any man's arsenal. The main tool will be screwdriver or a set of screwdrivers with different attachments, since fasteners may differ in the type of slot.
In addition to the main tool, do not forget about a soft rag or cardboard, which needs to be laid on the floor in front of the refrigerator. This will protect the decorative coating of the door from chipping if it accidentally falls, and will also protect the floor covering from scratches. Some models may require hex key (usually 4 mm or 5 mm), which is often included with the appliance.
⚠️ Attention: Before starting any work, be sure to disconnect the refrigerator from the power supply! Unplug the plug from the socket to eliminate the risk of electric shock when dismantling controls or lighting.
It is better to prepare a list of required equipment in advance so as not to interrupt the process of searching for the required part. The absence of even one small element can delay the work indefinitely.
- 🛠️ A set of screwdrivers (phillips and flat) or a screwdriver with a bit.
- 🔧 Hex keys (often required for hinges).
- 🧤 Work gloves to protect your hands from sharp edges.
- 📦 Container for folding screws so as not to lose them.
- 🧼 Soft cloth for wiping the surface and protecting the floor.
Design features of doors of Beko models
Refrigerators Beko are produced in various modifications, and the design of their door systems can vary significantly. In budget and mid-range models, the classic design is often found, where the upper and lower hinges are removable, and the axis is built into the canvas. In more expensive series with technology NoFrost the system may be complicated by the presence of additional fastenings for air ducts.
It is important to understand that not all models allow you to hang both doors. Often the bottom door (of the freezer) has a fixed hinge or design features that do not allow the handle to be moved. In such cases, it is allowed to rehang only the upper door of the refrigerator compartment, which already solves the problem of access.
Is it possible to rehang the door if the handle is built-in?
In models with hidden handles (recesses in the body), problems with transfer usually do not arise. If the handle is overhead and asymmetrical, you will need to find a set of mirror caps or handles, since the old ones may not fit on the new side.
Particular attention should be paid to the sealing system. Rubber seal on doors Beko often has a specific profile, which, when hung, may require heating to restore its shape. It is also worth checking for decorative plugs on the opposite side, which will need to be rearranged.
| Model type | Possibility of overweight | Nuances |
|---|---|---|
| Single-chamber | Full (top and bottom) | Simple hinge design |
| NoFrost (double-chamber) | Partial or full | Need disconnect the wires |
| Side-by-Side | Not recommended | Complex system, risk of deformation |
| Built-in | Depends on the facade | Requires overweight of the furniture door |
Removing the top refrigerator doors
You should always start work from the top of the unit. The first step is to remove the top decorative panel, if it is present on your model Beko. It can be attached with latches or small screws that need to be carefully unscrewed. The upper hinge, which holds the bulk of the door, is hidden under the panel.
After gaining access to the fasteners, it is necessary to fix the door in the open position so that it does not slam shut. Use stops or have an assistant hold the blade. Unscrew the screws securing the top hinge to the refrigerator body and carefully remove the hinge itself.
⚠️ Warning: The top hinge may be heavy and have sharp edges. Be careful not to injure yourself or drop the metal element on your foot.
Now that the top fastening is freed, you can lift the door and remove it from the bottom axis. This should be done with a sharp but controlled upward movement. If the door is tight, rock it slightly from side to side, but do not use excessive force so as not to tear out the lower pin.
- 🔩 Remove the top decorative cover.
- 🔧 Unscrew the upper hinge bolts.
- 🚪 Remove hinge and carefully lift the door up.
- 🧱 Place the door on a prepared soft surface.
Working with electrics and the lower hinge
If your refrigerator is equipped with a display on the door or an open door alarm system, electrical wires run inside the panel. In models Beko the connectors are usually located at the top of the door or in the top hinge area. It is necessary to carefully disconnect contact groupwithout pulling the wires themselves.
After removing the upper door, we move on to the lower one. An intermediate hinge is located here, which is often a common fastening element for both doors. Removing it requires special attention as it supports the weight of the bottom freezer door. Unscrew the mounting bolts and remove the loop.
The lower door is removed in the same way as the upper one: it needs to be lifted up to free it from the lower pin. Be prepared for the fact that it may be heavy, especially if there are shelves or drawers left inside (although it is better to remove them in advance). After removing the door, only the lower mating part of the hinge will remain on the body, which also needs to be dismantled or rearranged.
In some models axial bushing it may become sour or rusty. In this case, do not try to knock it out with a hammer. Treat the connection with a penetrating lubricant (for example, WD-40) and give it time to act, otherwise you can damage the threads in the refrigerator body.
Transfer of fittings and handles
The most labor-intensive stage is the transfer of the handle and plugs. At the end of the removed door you will find holes closed with plastic plugs. They need to be carefully pryed off with a thin screwdriver and removed. On the opposite side, where the handle will be moved, these holes can be closed with decorative inserts to match the color of the body.
Handle in refrigerators Beko often attached to screws, accessible from inside the door or through special holes. Unscrew the fasteners and remove the handle. Then install it in a new place using the prepared holes. Make sure that the screws are tightened tightly, but not fanatically, so as not to damage the plastic body of the handle.
☑️ Transferring accessories
Do not forget to rearrange the stops or clamps, if they are provided for by the design. Some models require the latch mechanism itself to be reversed inside the door so that the magnet or lock tab is in the correct position. To do this, you may need to remove the inner panel of the door, which is done by unscrewing the screws around the perimeter.
Assembling the structure on the new side
Assembly is carried out in the reverse order of disassembly. Start by installing the bottom support sleeve or hinge onto the new side of the housing. Make sure it sits perfectly horizontal, otherwise the door will warp. Tighten the mounting bolts until they stop.
Then hang the bottom door of the freezer. Align the hole in the bottom of the door with the installed bushing and lower the leaf down until it clicks or makes a tight fit. After this, an intermediate hinge is installed, which secures the lower door and serves as a support for the upper one.
The upper door is installed last. First, connect the electrical connectors (if any), carefully placing the wires in the designated channels so that they are not pinched. Then put the door on the intermediate hinge axis and secure the upper hinge to the body.
⚠️ Attention: When tightening the hinge bolts, maintain uniform force. Overtightening one bolt can lead to distortion of the entire system and a loose fit of the seal.
The final touch is the installation of decorative panels and plugs in place of the old holes. Check that all plastic elements fit into their grooves without gaps. If you see gaps, it means that some element did not fit correctly or the fixing tab is lost.
Adjustment and checking tightness
After assembly, you need to check the quality of work. The door should open freely, but at an opening angle of more than 30-40 degrees, it should be closed independently thanks to magnets. If the door opens too tightly or, on the contrary, slams, adjustment of the hinges is required hinge adjustment.
To check the tightness, use a simple test with a sheet of paper. Clamp the sheet between the door and the body in different places around the perimeter. The sheet should be removed with noticeable effort. If the paper falls out freely or is removed too easily, the seal is broken in this place.
If distortions are detected, slightly loosen the mounting bolts of the problematic hinge, align the door and again tighten the bolts. Models Beko often provide the ability to adjust the height of the legs of the refrigerator, which also affects the angle of inclination and self-closing of the doors.
What to do if, after rehanging, the door does not close tightly?
Check whether the products on the shelves are interfering with closing. Make sure the seal is not twisted and lies flat. If the problem is with the hinges, try loosening them and re-centering the door. Also check whether the plugs are installed correctly in place of the old handle - they should not protrude and interfere with the fit.
Do you need to wait before turning on the refrigerator after hanging it?
If you did not tilt the refrigerator more than 45 degrees during work, you can turn it on immediately. If the unit tumbled heavily or lay on its side, let it stand upright for 2-4 hours to allow the oil to drain into the compressor.
Is it possible to hang the door if it has a display?
Yes, it is possible, but this requires more care. The main thing is not to damage the wire loop when rearranging. The length of the wire in Beko models usually allows you to move the connector to the other side, but in rare cases extension may be required, which is best left to a specialist.
Where should the old holes from the handle be put?
Plastic plugs that match the color of the case are often included with the refrigerator or in a bag with documents. If they are not there, you can use decorative stickers or carefully paint over the hole if it is deep and not through, although this is less aesthetically pleasing.