Re-hanging the doors of the Candy refrigerator: instructions with photos and expert advice

Hanging refrigerator doors Candy is a task that almost every owner faces sooner or later. The reasons can be different: moving to a new kitchen with a different layout, the desire to optimize the space, or a banal inconvenience when opening. Fortunately, most models Candy (including popular series CCBN, CDBN, CSW) structurally provide for this possibility. But without preparation, the process can result in a chipped coating, skewed hinges, or even damage to the seal.

In this article you will find not just the “unscrew and screw” steps, but detailed analysis taking into account typical errorsthat beginners make. We will look at what tools are really needed (spoiler: the included screwdriver is not always enough), how to properly remove the door so as not to damage the hinges, and what to do if, after rehanging, the refrigerator begins to close poorly. We will separately dwell on the nuances for models with water dispenser and two-chamber units, where reconfiguration of the hinges of the upper and lower chambers is required.

If you have never done such work, do not worry. The process is easier than it seems if you know the key points. For example, in 90% of cases, the problem "the door does not close after hanging" is associated with incorrect adjustment of the top hinge or a forgotten seal retainer. And now - to the point!

Preparation: tools and conditions

Before taking a screwdriver, make sure that you have everything you need. The specificity of refrigerators Candy is that some models (for example, Candy CCBN 6185 or CDBN 6205) may require non-standard bits or hexagons. Here is the complete checklist:

• ✅ Screwdrivers: cross (PH2) and flat (3-4 mm) - a must! Some models use child-proof screws (with a central pin), so you may need a specialized bit TR10 or TR15.
• ✅ Hex wrench 4-5 mm - to adjust the hinges in models with the system EasyDoor.
• ✅ Wrench 10–13 mm - if the hinges are fastened with nuts (valid for older series Candy until 2018).
• ✅ Making tape - to secure the door when removing and avoid scratches on the body.
• ✅ Level (bubble or laser) - for checking the vertical position after installation.
• ✅ Silicone lubricant - for processing hinges after rehanging (prevents squeaking).

Also prepare your workspace:

• 🔌 Unplug the refrigerator and defrost (if required). In models with No Frost it is enough to let it stand for 1-2 hours.
• 🧊 Remove all products and shelves from the door - they add weight and complicate manipulation.
• 📏 Measure the gaps: between the door and the body there should be at least 2-3 mm around the entire perimeter.

⚠️ Attention! If your refrigerator Candy is equipped with an electronic display (series Candy Smart Touch), you may need to reset the settings after rehanging. In the instructions for the model, look for the section Door Reversal Mode —activating it will prevent sensor errors.

Removing the door: step-by-step instructions

Let's start from the very beginning important stage - dismantling the door. The main rule here is: bottom to top. If you start from the top hinge, the door may fall and damage the hinges or seal.

Step 1. Fixing the door. Adhere masking tape to the refrigerator body and door in 2-3 places so that it does not move when unscrewed. In models with a dispenser (Candy CDBN 6205 W), first remove the water tray - it is secured with latches.

Step 2. Dismantling the lower hinge. Open the door 90° and find the protective hinge cover (usually it is plastic, removed by prying it off with a screwdriver). Under it you will see 2-3 screws - unscrew them not all the wayso that the door does not fall. In some models, the screws are hidden under a decorative trim - it must be carefully moved to the side.

Step 3. Removing the door. Holding the door with one hand, completely unscrew the screws of the lower hinge. Then lift the door up to remove it from the top hinge. If the door is “jammed”, do not pull by force - check whether you forgot to unscrew the fixing bolt on the back of the case (relevant for models Candy CSW).

Step 4. Dismantling the top hinge. After removing the door, unscrew the screws of the top hinge and remove it from the body. Please note: in some models, the top hinge is attached not only to the door, but also to the inner panel of the refrigerator (for example, in Candy CCBN 6185In this case, you will need to unscrew additional screws from the inside.

⚠️ Attention! If your refrigerator Candy is equipped with a system EasyDoor (soft closing), when removing the door, do not pull it towards you - first press the latch in the top hinge (usually it is marked in red or blue). Otherwise, you can damage the shock absorption mechanism.

Moving the hinges to the other side

Now you need to move the hinges to the opposite side. There is an important nuance here: in most models Candy holes for the hinges are already provided. factory, but they are closed with plugs. Do not try to drill new ones - this will lead to corrosion and loss of warranty (if it is still valid).

Step. 1. Removing the plugs. On the opposite side of the body and door you will see plastic or rubber plugs. Pry them off with a flat screwdriver and remove them. There may be factory grease inside the holes - do not remove it!

Step 2. Installing the hinges. Move the upper and lower hinges to the new side, aligning the holes. Tighten the screws not all the way —first you need to adjust the position of the door. In models with a dispenser (Candy CDBN), first install the bracket for the water tray, then the hinge.

Step 3. Check symmetry. Attach the door to the hinges and check if the holes match. If the door “sticks”, you may need to sharpen the plastic protrusions on the body (valid for models up to 2020), use a file or sandpaper, but not. overdo it - just remove 1-2 mm.

If your model has asymmetrical hinges (for example, in Candy CCBN 6185 the left and right hinges differ in shape), do not try to swap them - this will lead to a loose fit of the door. In this case, you need to purchase a set of hinges for the opposite side (the article number is usually indicated in the instructions).

Door installation and adjustment

Now the most crucial moment is installing the door on new hinges. This is where many people make the mistake of tightening the screws all the way right away. In fact, you first need to adjust the position of the door along three axes:

1. Vertical —the door should hang evenly, without distortions. Check with a level.
2. Horizontal —the upper edge of the door must be parallel to the body.
3. Fit —the seal must fit evenly around the entire perimeter.

Step 1. Hanging the door. Carefully slide the door onto the top hinge, then align it with the bottom. Tighten the bottom hinge screws 70–80% - they will be used for adjustment.

Step 2. Preliminary adjustment. Close the door and check the gaps:

• ✅ Top and bottom - 2-3 mm.
• ✅ On the sides - 1-2 mm.
• ✅ The seal should be compressed evenly (you can check it with a sheet of paper - it should hold if pressed with a door).

If there are gaps uneven, loosen the screws and adjust the position.

Step 3. Final fixation. After adjustment, tighten all screws until they stop. In models with EasyDoor additionally check the operation of the shock absorber - the door should close smoothly, without jerking.

What to do if the door does not close after rehanging?

Most likely there is a problem in the top loop. Loosen its screws and slightly lift the door up (by 1–2 mm), then fix it. If this does not help, check the seal - it may have moved or bent. In extreme cases, you may need to replace the seal (the article for Candy usually begins with C00...).

Nuances for two-chamber refrigerators

If you have a two-chamber refrigerator Candy (for example, CDBN 6205 or CCBN 6185), the process is complicated by the need to reconfigure both doors the refrigerator and freezer compartments. There are several key points here:

1. Procedure. Always start with the top door (refrigerator compartment), then move on. to the bottom (freezer). If done the other way around, the upper door may block access to the fastenings of the lower one.

2. Middle hinge. In two-chamber models there is an additional middle hinge that secures both doors to each other. It must be removed last of all during dismantling and installed first of all during assembly. Otherwise the doors will hang loose.

3. Adjusting the gaps. There should be a gap of 3-4 mm between the doors. If the doors rub against each other, loosen the middle hinge screws and adjust the position.

⚠️ Attention! B models Candy with the system Twin Cooling (separate cooling of the chambers) after rehanging, an error may occur E1 or E2. To reset the error, unplug the refrigerator for 5 minutes, then turn it on again.

Checking and finishing touches

After installing the door, you need to check its operation in several modes:

1. Tightness test. Close the door and try to stretch a sheet of paper around the perimeter of the seal. If the sheet falls out, the seal does not fit tightly. In this case, you need to tighten it. hinges or adjust the position of the door.
2. Checking the opening. The door should open smoothly, without jerking. If it “sticks”, lubricate the seal with silicone spray (do not use oils!).
3. Weight test. Hang shelves on the door and load them with food (for example, bottles). If the door sags, tighten the bottom hinge.

Also pay attention to the following points:

• 🔧 If the refrigerator is equipped water dispenser, after rehanging, check the connection of the tube. In models Candy CDBN it may bend - this will lead to leakage.
• 📱 In refrigerators with electronic control (Candy Smart Touch) after rehanging may be required sensor calibration. To do this, press the button Super Cool for 5 seconds - a message will appear on the display Calibration OK.
• 🔄 If the seal is deformed when removing the door, warm it up with a hairdryer (temperature 50–60°C) and shape with your hands. Do not use hot water - this will ruin the material!

Common mistakes and how to avoid them

Even if you carefully follow the instructions, you can make mistakes that will lead to problems in the future. Here are the most common ones:

1. Tightening the screws. If you tighten the hinge screws too much, this can deform the plastic bushings inside the door. As a result, over time the door will begin to open. sag. Solution: tighten the screws with a force of 1.5–2 Nm (use a torque wrench, if available).

2. Ignoring the plugs. If you do not remove the factory plugs before installation hinges, they will interfere with the door's tight fit. Worse, they may crack when tightening the screws. Solution: always check the holes for plugs.

3. Incorrect procedure. Many first remove the top hinge, and then the bottom. This can cause the door to fall and damage the hinges. Solution: always start with the bottom hinge!

4. They forget about the middle hinge. In two-chamber models, the middle hinge is often remains unadjusted, causing the doors to rub. Solution: after installation, check the gap between the doors (3-4 mm).

5. Do not check the seal. If the seal is bent or displaced during removing the door, the refrigerator will keep the temperature worse. Solution: after installation, warm the seal with a hairdryer and check the fit with a sheet of paper.

⚠️ Attention! If after rehanging the refrigerator Candy began to make noise louder than usual, most likely the door is pressing on the body and transmitting vibration. Check the gaps and, if necessary, loosen the hinges.

FAQ: Answers to frequently asked questions

Do I need to defrost the refrigerator before reversing the door?

For models with No Frost defrosting is not necessary, but it is recommended to unplug the refrigerator for 1-2 hours to avoid condensation on the seal. In refrigerators with a drip system (Candy CSW), defrosting is required - otherwise water may get on the electrical contacts. hinges.

Is it possible to hang the door on a Candy refrigerator yourself if you have no experience?

Yes, but only if you are confident in your abilities. The main thing is to take your time and follow the instructions. If the refrigerator is under warranty, it is better to contact a service center so as not to lose the warranty (Smart Touch) independent re-hanging can lead to failure of the settings.

How long does it take to re-hang the door?

On average - 1.5-2 hours for a single-chamber refrigerator and 2.5-3 hours for a two-chamber refrigerator. The most time is spent on adjusting the hinges and checking the tightness. If you have never done this, budget an additional 30-60. minutes.

What to do if the door does not close after rehanging?

Most likely, the problem is in the upper hinge. Loosen its screws and slightly lift the door up (by 1-2 mm), then fix it:

1. Check the seal - it could. bend.
2. Make sure that the middle hinge (in two-chamber models) does not interfere with closing.
3. Check if anything is blocking the door from the inside (for example, shelves or drawers).

In extreme cases, replacing the seal may be necessary.

Do you need to lubricate the hinges after rehanging?

Yes, but only with silicone grease! Oils or WD-40 cannot be used - they attract dust and thicken over time, which leads to squeaking. Apply 1-2 drops of lubricant to the hinge hinges and open/close the door several times to distribute. composition.